Simplicity 1691521 Operator's Manual
  1. Manuals
  2. Brands
  3. Simplicity Manuals
  4. Snow Blower
  5. 1691521
  6. Operator's manual

Simplicity 1691521 Operator's Manual

Snowthrower & hitch
Hide thumbs Also See for 1691521:
Table of Contents

Advertisement

Quick Links

How to use this file...(Operators Manuals)
————————————————————————————————————————————–––
Instructions for
Print Vendors (Paper Manuals)
Paper Size:
* 11 x 17
* Body—50 lbs brilliant white offset or equivalent.
* Cover—on pre-printed two-tone "Swash" stock.
P r e s s :
* Body—1-color, 2-sided
* Cover imprint —1-color, 1-sided
Bindery:
* Saddle Stitch, Face Trim
* Face Trim
C O V E R S :
* This file contains several manuals, which differ only in their covers.
* Covers are all present at the beginning of this file.
* Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover.
• Check the front cover for the individual part number (typically a 171xxxx number).
B O D Y :
• The body of the manual is identical, regardless of the cover used.
* REMEMBER: ODD number pages are ALWAYS right hand pages, and EVEN number are ALWAYS
left hand pages.
G e n e r a l :
* This instruction page is NOT part of the manual and must NOT be printed.
• Pages labeled with the text "THIS PAGE INTENTIONALLY BLANK" are placement pages ONLY,
and should NOT be printed.
————————————————————————————————————————————–––
If you have further questions on how to utilize this file, please contact
Simplicity Technical Publications Department at (262) 284-8647.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1691521 and is the answer not in the manual?

Questions and answers

Related Manuals for Simplicity 1691521

Summary of Contents for Simplicity 1691521

  • Page 1 • Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY, and should NOT be printed. ————————————————————————————————————————————––– If you have further questions on how to utilize this file, please contact Simplicity Technical Publications Department at (262) 284-8647.
  • Page 2 THIS PAGE INTENTIONALLY BLANK...
  • Page 3 Attachment OPERATOR’S MANUAL Snowthrower & Hitch 36” Snowthrower Mfg. No. Description 1691521 36” Snowthrower Attachment 42” Snowthrower Mfg. No. Description 1691522 42” Snowthrower Attachment Hitch Mfg. No. Description 1692040 Hitch, Electric Lift (for Landlord / 1700 / 2700 Series) 1692041...
  • Page 4 Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA © Copyright 1998, Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.

  • Page 5: Table Of Contents

    Main Operation Warning Decal WHEN OPERATING TRACTOR CAUTION WITHOUT SNOWTHROWER ATTACHED, FLUID IN FRONT TIRES IS REQUIRED. 1716887 Part No. 1716887 © Copyright 1997 Simplicity Manufacturing, Inc. Tire Fluid Caution Decal (Regent Series Only) All Rights Reserved. Printed in USA. TP 100-2014-05-AT-SMA...

  • Page 6: Safety Rules

    Safety Rules Read these safety rules, and the safety rules in your tractor Operator’s Manual, and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. The triangle in the text signifies important cau- tions or warnings which must be followed.

  • Page 7: Operation

    Operation Controls Read and understand the instructions in your tractor Operator’s Manual. See Figure 1 for location, name, and description of the snowthrower controls. Checks Before Starting 1. Refer to the Maintenance & Adjustments section of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service.

  • Page 8: Daily Storage

    Operation Starting & Stopping Snowthrower & Hitch Removal 1. Start the tractor engine. Set engine throttle at 1/2 Remove the snowthrower and hitch in the reverse order speed. of installation. Note the following: 2. Lower the snowthrower. • Always remove the 4-link chain from the spring assist bracket to prevent interference with front steering 3.

  • Page 9: Maintenance

    Maintenance Inspect, Adjust & Lubricate Drive Chain Schedule For Normal Care See Figure 2. Care Required Schedule 1. Remove the two nuts (F) and chain guard (E). Clean snow and ice from After each use. 2. Check the chain for wear or damage. Replace chain snowthrower.
  • Page 10 Maintenance Lubricate Snowthrower Figure 3. Lubricate Drive Shaft & Auger Shaft...

  • Page 11: Belt Replacement

    Belt Replacement / Adjustment BELT REPLACEMENT 1. Loosen the drive belt by turning the handle (C, Figure 2. Remove the belt from the pulley (D, Figure 4) inside the snowthrower and remove the snowthrower from the tractor. 3. Loosen the lockwashers and nuts securing two belt stops on idler pulleys (A and E, Figure 4).

  • Page 12: Lift Rod Adjustment

    Adjustment Lift Rod Adjustment MANUAL LIFT MODELS The lift lever can be placed in one of three notches and is held in position by the lever latch. (see Figure 8). When the lever latch is placed in notch 1 the lift lever should be applying downward pressure on the snowthrower.

  • Page 13: Troubleshooting

    Troubleshooting Locate the problem you’ve encountered in the chart below. Check the possible causes one at a time in the order list- ed. Correct any problems that are found and operate the snowthrower to see if you have eliminated the problem. WARNING To avoid serious injury, perform maintenance on the tractor or snowthrower only when the engine is stopped, parking brake is set, and all moving parts have stopped.

  • Page 14: Snowthrower Assembly

    Regent Snowthrower Assembly CAUTION Do not let the pivot bearing (D, Figure 9) support the weight of the control rod or the bearing could be damaged. SNOWTHROWER ASSEMBLY Assemble Support Arm and Control Rod 1. See Figure 9. Attach the support arm (E) to the frame with the 1"...
  • Page 15 Regent Snowthrower Assembly Up-stop Up-stop Hitch Bracket (Mounted On Inside) Figure 12. Hole Pattern - Left Side Figure 11. Up-stop Bracket Orientation Assemble Hitch Brackets and Up-Stops Up-stop Refer to Figure 11 for up-stop orientation. 1. Mount the hitch bracket to the inside of the snowthrower and the up-stop bracket to the outside Hitch Bracket of the snowthrower using capscrews and flange lock-...

  • Page 16: Hitch Installation

    Regent Hitch Installation Assemble the Deflector Refer to Figure 15. 1. Attach the deflector (C) to the discharge chute with two screws (H), washers (G), spacers (F), washers (A), lockwashers (E) and nuts (D). 2. Position the bolt (I) and washer (A), then thread the knob (B) onto the bolt (I).
  • Page 17 Regent-Hitch Installation A. Hitch Assembly B. Rear Hitch Bracket C. Washers (Qty. 2) D. Hairpin Clip (Qty. 2) E. Pin F. Spring Clip (Qty. 4) G. Clevis Pin, 3/8 (Qty. 2) H. Rod I. Reflectors (Qty. 2) J. Capscrew, 3/8-16 x 2 K.

  • Page 18: Snowthrower Installation

    Regent-Hitch Installation Figure 19. Snowthrower Installation A. Safety Clips D. Snowthrower Bracket B. Hitch Arms E. Up-Stop Brackets C. Clevis Pin Figure 20. Belt Routing A. V-pulley C. Electric Clutch Pulley (V-Pulley) B. Idler Pulley D. Snowthrower Pulley (V-Pulley) E. Backside Idler Pulley SNOWTHROWER INSTALLATION CAUTION After snowthrower installation if the tractor hood is...
  • Page 19 Regent-Snowthrower Installation Install lift rod to inside of bracket as shown. Figure 22. Installing Lift Rod to Manual Lift Lever A. Front Attachment Lift Rod C. Hair Pin Clip B. Manual Lift Lever Figure 23. Installing Lift Rod to Snowthrower A.

  • Page 20: Snowthrower Assembly

    Broadmoor-Snowthrower Assembly SNOWTHROWER ASSEMBLY Assemble Support Arm and Control Rod NOTICE Do not let the pivot bearing (D, Figure 26) support the weight of the control rod or the bearing could be damaged. 1. See Figure 26. Attach the support arm (E) to the frame with the 1"...
  • Page 21 Broadmoor Snowthrower Assembly Figure 29. Installing the Hitch Brackets and Spacers Figure 28. Discharge Chute A. Hitch Brackets E. Capscrew, 1-1/4" A. Washer, 5/16 F. Spacer B. Capscrew, 1" F. Lockwasher B. Knob G. Washer, 5/16 C. Locknut, Flange G. Nut C.

  • Page 22: Hitch Installation

    Broadmoor Hitch Installation Install the Heat Shield 1. Install the heat shield as shown in Figure 32. Position the shield 1/8” right of the “T” of “HOT”. CAUTION The heat shield shown in Figure 32, is supplied with the hitch assembly and must be installed before installing hitch assembly.
  • Page 23 Broadmoor-Hitch Installation A. Hitch Assembly B. Rear Hitch Bracket C. Washers (Qty. 2) D. Hairpin Clip (Qty. 2) E. Pin F. Spring Clip (Qty. 4) G. Clevis Pin, 3/8 (Qty. 2) Insert Pin “E” Through H. Rod the Top Hole I.

  • Page 24: Snowthrower Installation

    Broadmoor-Hitch Installation Figure 36. Attaching the Snowthrower A. Spacers D. Safety Clips Figure 37. Belt Routing B. Hitch Arms E. Snowthrower Bracket A. V-pulley C. Electric Clutch Pulley (V-Pulley) C. Clevis Pin B. Idler Pulley D. Snowthrower Pulley (V-Pulley) E. Backside Idler Pulley SNOWTHROWER INSTALLATION CAUTION After snowthrower installation if the tractor hood is...
  • Page 25 Broadmoor-Snowthrower Installation Install lift rod to inside of bracket as shown. Figure 40. Installing Lift Rod to Snowthrower Figure 39. Installing Lift Rod to Manual Lift Lever A. Rod Guide Assembly A. Front Attachment Lift Rod C. Spring Clip B. Hair Pin Clip B.

  • Page 26: Snowthrower Assembly

    Landlord-Snowthrower Assembly SNOWTHROWER ASSEMBLY Assemble the Support Arm and Control Rod CAUTION Do not let the pivot bearing (D, Figure 43) support the weight of the control rod or the bearing could be damaged. 1. See Figure 43. Attach the support arm (E) to the frame with the 1"...
  • Page 27 Landlord-Snowthrower Assembly Figure 45. Deflector Figure 46. Installing the Hitch Brackets A. Washer, 5/16 F. Spacer A. Hitch Brackets C. Flange Locknut B. Knob G. Washer, 5/16 B. Capscrew, 1" C. Deflector H. Screw, 5/16 D. Nut, 5/16 I. Carriage Bolt, 5/16 E.
  • Page 28 Landlord-Snowthrower Assembly CAUTION The heat shield shown in Figure 49, is supplied with the hitch assembly and must be installed before installing hitch assembly. Damage to snowthrower could occur if heat shield is not installed. Remove heat shield when removing snowthrower and hitch assembly.

  • Page 29: Hitch Installation

    Landlord-Hitch Installation Figure 53. Installing Hitch to Rear Bracket A. Rear Hitch Bracket D. Washer B. Lift Lever Rod E. Hitch C. Hair Pin Clip F. Clevis Pin Figure 52. Manual Lift Lever Assembly A. Lift Lever Assembly. C. Hair Pin Clip B Guide Bracket D.

  • Page 30: Snowthrower Installation

    Landlord-Snowthrower Installation A. Hitch Assembly.. B. Rear Support Assembly.. C. Washers (Qty. 2) D. Hairpin Clip (Qty. 2) E. Pin F. Spring Clip (Qty. 4) G. Clevis Pin, 3/8 (Qty. 2) Install Pin “E” Through H. Rod the Bottom Hole. I.
  • Page 31 Landlord -Snowthrower Installation Figure 58. Belt Routing A. V-pulley C. Electric Clutch Pulley (V-Pulley) B. Idler Pulley D. Snowthrower Pulley (V-Pulley) E. Backside Idler Install the Belt Figure 59. Belt Installation & Adjustment A. Trunion D. Capscrew 1. See Figure 59. To install the belt on the electric B.
  • Page 32 Landlord-Snowthrower Installation Install the Spring Assist Landlord/GT/2700/1700 Series Frame hole is located on front, left side; in front of engine NOTE: The spring assist is not required on models equipped with electric lift. However, if the snowthrower leans to one side the spring assist can be installed to correct this.

  • Page 33: Standard Torque Specifications

    Torque Specifications TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) SIZE SAE GRADE #2 SAE GRADE #5 SAE GRADE #8 in/lbs in/lbs in/lbs ft/lbs ft/lbs ft/lbs 8-32 8-36 10-24 10-32 1/4-20 10.9 16.3 1/4-28 13.6 19.0 5/16-18 15.0 23.1 34.0 5/16-24 16.3...

  • Page 34: Standard Fastener Identification

    Standard Hardware STANDARD FASTENER IDENTIFICATION CHART HEX CAPSCREW Hardware sizes given in the illustrations throughout this manual. If a washer or nut is identified as “washer, 1/2” or “nut, 1/2”, this means the inside diameter is 1/2 CARRIAGE BOLT inch If a screw is identified as “screw, 1/2 x 2”, this means the shaft diameter is 1/2 inch and the...

  • Page 35: Lift Lever Kit Installation Instructions

    Installation Lift Lever Kits Mfg. Nos. 1691832 & 1692623 Instructions BROADMOOR / 1600 / 2600 SERIES INSTALLATION - 1691832 Kit Contents: Ref. Qty. Part No. Description 1704712 Pivot Bracket 1923325 Capscrew, 5/16-18 x 7/8 1924433 Nut, 5/16-18 1704713 Lift Bracket 1704715 Guide 1665591...
  • Page 36 Rear Hitch Bracket Lift Lever Installation M A Simplicity Mfg. Inc. Form No. 1715019 500 N Spring Street / PO Box 997 Rev. 6/97 Port Washington, WI 53074-0997 USA © 1997 Simplicity Manufacturing, Inc. All Rights Reserved TP 200-2069-02-AT-SMA...

This manual is also suitable for:

1691522169204116926221692040

Table of Contents

Save PDF