Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for WTI Sidewinder SW720A
Summary of Contents for WTI Sidewinder SW720A
- Page 1 SIDEWINDER Series SW720A : 120VAC Installation Manual R0710...
-
Page 2: Table Of Contents
SIDEWINDER SERIES: SW720A …………………………………………… Page 6 SAFEGUARDS, TOOLS & INSTALLATION ………………………………… Page 7 MOUNTING …………………………………………………………………. Page 8 SIGNAL CONNECTIONS …………………………………………………… Page 10 SEALING & PRESSURIZATION ……………………………………………. Page 14 TECHNICAL SPECIFICATIONS ……………………………………………. Page 16 Page 2 of 17 ©WTI (Wireless Technology, Inc.) : Sidewinder... -
Page 3: Information
The software / firmware furnished with the Every effort has been made to insure that equipment is confidential to and is this WTI system is of the highest quality. copyrighted by Wireless Technology, Inc. (WTI) This product has been carefully inspected... -
Page 4: Product Warranty & Repair
In no event shall WTI or its Authorized Dealers be liable for special or consequential damage arising from the use of this product, or any delay in the performance of this warranty due to causes beyond its control. -
Page 5: Product Warranty And Repair
PRODUCT WARRANTY AND REPAIR REPAIR AUTHORIZATION Please contact Wireless Technology, Inc. (WTI), to obtain a repair authorization number (RA) and provide the following information: 1.) Product Model & Serial Numbers. 2.) Date of shipment, purchase order number, sales order number or WTI invoice number. -
Page 6: Sidewinder Series: Sw720A
Please examine the equipment carefully when unpacking the shipping container. If any damage is noted please be sure to file a claim with the carrier. WTI is not responsible for any damage that occurs during shipping. Please verify that all of the contents are present and carefully check the packing material for any loose items before recycling it. -
Page 7: Safeguards, Tools & Installation
2.) The Sidewinder SW720A camera draws up to 50 Watts maximum, which translates to about 0.59 Amps at the low line voltage limit of 85VAC. This will result in an AC Line voltage drop of no more than 6VAC over the maximum 750 foot umbilical cable run. -
Page 8: Mounting
The camera may NOT be mounted with the base facing horizontally. The base of the Sidewinder SW720A camera has four ¼-20 screw holes that are equally spaced, 90° apart, on a 4.75” diameter circle. If mounting screws other than those provided with the camera are used, the length of the mounting screws should be selected so that the screws penetrate no more than 0.75 inches into the base. - Page 9 MOUNTING Model #SWWM1 and #SWVPA: Wall Mount with Vertical Model #SWWM1: Wall Mount Pole Mount Adapter Model #SWPTM1: Post Top Mount Model #SWHPM1: Horizontal Pole Mount ©WTI (Wireless Technology, Inc.) Page 9 of 17...
-
Page 10: Signal Connections
SIGNAL CONNECTIONS The Sidewinder SW720A camera is supplied with a 36 inch umbilical cable to allow the cable to be routed through the camera mount before the actual physical installation of the camera. Signal Connections The Sidewinder SW720A is provided with a 36 inch umbilical cable and is available with either an AMP 16 pin circular plastic connector or an 18 pin MS Style connector at the end. - Page 11 Data Shield Green White Black ------ ------ ------ ------ 85-265 AC Line Input 18AWG Black (high/hot) AC Line Neutral 18AWG White (low) Cable Shield Overall Shield 115 VAC Ground 18AWG Green ------ ©WTI (Wireless Technology, Inc.) Page 11 of 17...
- Page 12 115 VAC Ground 18AWG Green Cable Shield Overall Shield ------ ------ Video RG-59 Center Black Data Ground Data Shield Green White AC Line Neutral 18AWG White (low) 85-265 AC Line Input 18AWG Black (high/hot) ©WTI (Wireless Technology, Inc.) Page 12 of 17...
- Page 13 In the case of units with a stripped and tinned umbilical cable, the video cable will be terminated with a male BNC connector. Data connections Communications with the Sidewinder SW720A are provided through the TX+, TX-, RX+ and RX- signals which are RS-485 compatible and support multiple cameras on the same communication segment.
-
Page 14: Sealing & Pressurization
There are internal 120Ω termination resistors for both the TX and RX signal pairs that may be enabled or disabled through the use of the WTI HHC-SW hand held controller unit. The factory shipped default state for the 120Ω terminations is for both the TX and RX terminations to be enabled. - Page 15 SEALING & PRESSURIZATION The Sidewinder SW720A camera is provided with a Schrader valve to allow periodic replenishment of the dry Nitrogen in the camera housing tube. Since no sealing system will remain 100% airtight indefinitely, it may be necessary to replenish the dry Nitrogen occasionally.
-
Page 16: Technical Specifications
5 PSI (34 Rating kPa) with dry nitrogen. IP67 pan/tilt Power Transients / Conforms to NEMA TS2, Interruptions paragraph 2.1.6 assembly. Conforms to NEMA TS2, paragraph Shock 2.2.10 ©WTI (Wireless Technology, Inc.) Page 16 of 17... - Page 17 Due to Wireless Technology, Inc. (WTI) continuing efforts to engineer the best product that is most responsive to our customer’s needs, the above specifications are subject to change without notice. ©WTI (Wireless Technology, Inc.) Page 17 of 17...
Need help?
Do you have a question about the Sidewinder SW720A and is the answer not in the manual?
Questions and answers