PetTronix RoamEO Quick Manual

PET MONITOR SYSTEM
THANK YOU
for purchasing the RoamEO Pet Monitor System. The
TM
RoamEO system consists of the hand-held receiver, the RoamEO
TM
GPS/Radio collar, and a battery charger for use with both receiver and
collar. The RoamEO system works by having the RoamEO
TM
Collar obtain a fix from several GPS satellites in orbit, and transmitting
those coordinates via radio to the display unit, which will provide a
bearing/direction to your dog and a range/distance to your pet.
If you need assistance anytime please call our toll free numer
1-855-834-5622 or visit us at www.PETTRONIX.com
To insert a RoamEO
Battery into the Receiver,
flip up the metal ring
on the back of the
Display unit, turn the
ring counter-clockwise,
and pull the battery
cover off the Receiver
from the top and tilting
off the bottom where it is
held in place with a
slotted clip. Align the
arrow on the battery as
shown. Close the battery
compartment by aligning
the slotted clip on the
battery cover with the
bottom of the Receiver,
and tilting the cover
closed. Secure the
battery cover by turning
the metal ring clockwise.
Locating your Dog with the Display
Once your RoamEO
Collars have estab-
lished contact, you
1 2
now should take your
RoamEO Collar and
Receiver outside to
obtain a GPS lock.
1 A series of dots
will strobe on the
Display S creen until
the Receiver obtains
a GPS lock.
2 The display screen
has 8 directional
segments to point like
a compass in the
direction of your dog.
The RoamEO Collar
and hand-held Receiver
PetTronix unit are powered by
rechargeable, remov-
TM
able Lithium-Ion (li-ion)
batteries. After
purchase, please place
the Li-ion batteries in
the RoamEO Battery
Charger for two hours
to fully charge the
TM
batteries. Align the
arrow on the Battery as
GPS
shown in the Battery
TM
Charger cradle. When
fully charged, the
Battery Charger will
display a green LED
(red LED while charging).
The batteries are
interchangeable
between the RoamEO
Collar and the Receiver.
1 Turn on your Receiver
by pressing the Top
button on the left side.
*** IMPORTANT NOTE***
Procedure 2 and 3 are
performed at the factory
and is only necessary by
the user when registering
a new or additional collar.
2 Press and hold the
Middle Button until the
number 1 circle is
blinking on the display.
3 Press and hold the
Middle Button again
until both the number 1
Circle is blinking AND
the Paw outline is
blinking.
To locate your dog using
the Receiver, look at the
Display Screen and see
which Directional Segment
is highlighted. Turn the
Receiver until the Directional
Segment on the top of the
Display Screen begins to
strobe; that is the bearing
and direction to your dog.
Segmented
The Range Readout will
Directional
tell you the distance. Move
Edges toward your dog, changing
directions if different
Directional Segments light
up. If you are closer than
the GPS accuracy of the
unit (within 20 feet, or that
day's GPS accuracy of the
satellite constellation), all
of the Directional Segments
are highlighted. And the
word NEAR will appear.
Powering up the RoamEO
Collar and Receiver
Charge for 2 HOURS
before using
Charging
Fully Charged
Registering the RoamEO
Collar to the Receiver
1
2 3
To insert a RoamEO
Battery into the
RoamEO Collar,
unlatch the Collar
battery compartment
and remove the
battery cover. Place
the battery with the
arrow on the battery
face as shown.
Now turn on the
RoamEO Collar by
clipping the collar
ends together; the
RoamEO Collar
and Receiver
will automatically
establish contact.
To register a
second collar, follow
the same procedure
until the number 2
circle is blinking on
the display, and clip
the second collar
ends together.
NEAR