Advertisement
4.
By pressing MIN/MAX button once more, the min data of the selected channel will be shown. Also the time of recording this temperature will be displayed.
Min temperature
Minimum icon
6.
By pressing the MIN/MAX button more more time, the date of recording this temperature will be shown.
7.
Press one more time the MIN/ MAX button to advance to the indoor Max/ Min display
RESETTING THE OUTDOOR MAXIMUM/ MINIMUM RECORDS
Note:
•
It is required to reset the outdoor max/ min records of different channels separately.
•
The outdoor minimum and maximum record is to be reset separately.
1.
In normal display mode, press the CH button to select a channel. The channel Identification No. (channel No.) will be displayed above the outdoor temperature reading.
Note: The transmitter number will only be displayed if more than one transmitter is applied.
2.
Press the MIN/ MAX button once. The "max" icon will be displayed.
3.
Press the SET button, this will reset the outdoor maximum temperature and humidity record to the current value.
4.
Press MIN/ MAX button twice more to show the minimum data. The "min" icon will be displayed.
5.
Press the SET button, this will reset the outdoor minimum temperature and humidity record to the current value.
6.
Press six more times the MIN/MAX key to return to the normal display.
TEMPERATURE TRANSMITTER:
The range of the Thermo-hygro Transmitter may be affected by the temperature. At cold temperatures the transmitting distance may be decreased. Please bear this in mind when placing the
transmitter.
868 MHz RECEPTION
The Weather station should receive the temperature data within 5 minutes after set-up. If the temperature data is not received 5 minutes after setting up (not successfully continuously, the
outdoor display shows "- - -" ), please check the following points:
1.
The distance of the weather station or transmitter should be at least 1.5 to 2 meters away from any interfering sources such as computer monitors or TV sets.
2.
Avoid positioning the Weather station onto or in the immediate proximity of metal window frames.
3.
Using other electrical products such as headphones or speakers operating on the same signal frequency (868MHz) may prevent correct signal transmission and reception.
4.
Neighbours using electrical devices operating on the 868MHz signal frequency can also cause interference.
Note:
When the 868MHz signal is received correctly, do not re-open the battery cover of either the transmitter or Weather station, as the batteries may spring free from the contacts and force a false
reset. Should this happen accidentally then reset all units (see Setting up above) otherwise transmission problems may occur.
The transmission range is about 100 m from the transmitter to the Weather station (in open space). However, this depends on the surrounding environment and interference levels. If no
reception is possible despite the observation of these factors, all system units have to be reset (see Setting up).
POSITIONING THE WEATHER STATION:
The Weather Station has been designed to be hung onto wall or free standing.
To wall mount
Choose a sheltered place. Avoid direct rain and sunshine.
Before wall mounting, please check that the outdoor temperature and humidity values can be received from the desired locations.
1.
Fix a screw (not supplied) into the desired wall, leaving the head extended out the by about 5mm.
2.
Remove the stand from the Weather Station by pulling it away from the base and hang the station onto the screw. Remember to ensure that it locks into place before
releasing.
Free standing
POSITIONING
The Transmitter is supplied with a holder that may be attached to a wall with the two screws supplied. The Transmitter can also be position on a flat surface by securing
the stand to the bottom to the Transmitter.
To wall mount:
2. Clip the remote
Note:
Before permanently
signal is not received, relocate the transmitters or move them slightly as this may help the signal reception.
CARE AND MAINTENANCE:
SPECIFICATIONS:
Temperature measuring range:
Indoor
:
-9.9ºC to +59.9ºC with 0.1ºC resolution
(14.1°F to +139.8°F with 0.2°F resolution,
"OF.L" displayed if outside this range)
Time of recording
the min
temperature
Min humidity
With the detachable stand, the weather station can be placed onto any flat surface.
THE THERMO-HYGRO TRANSMITTER:
1. Secure the bracket onto a desired wall using the screws and plastic anchors.
temperature/humidity sensor onto the bracket.
fixing the transmitter wall base, place all units in the desired locations to check that the outdoor temperature reading is receivable. In event that the
47
Advertisement
