Table of Contents
Advertisement
Check for leaks. Make sure the regulator valve is securely fastened to the burner and the cylinder.
Make (2-3) oz. 0-90ml of leak solution by mixing one part liquid dishwashing soap with three parts water.
Make sure control knobs are off.
Spoon several drops of solution at the tank valve to regulator connection.
Inspect the solution at the connection, looking for bubbles. If no bubbles appear, the connection is secure.
If bubbles appear, you have a leak, recheck as :
Disconnect regulator from tank and reconnect, making sure the connection is secure.
Retest with solution. If you continue to see bubbles, replace the cylinder.
Danger: Failure to open lid while igniting the barbecue's burners or not waiting 5 minutes to allow the gas to clear if the barbecue does not
light, may result in an explosive flame-up which can cause serious bodily injury or death.
Open lid during lighting burners.
1.
Attempting to light the burner with the lid closed may cause an explosion! Make sure there are no obstructions of airflow to the gas unit. Spiders
and insects can nest within and clog the burner/venturi tube at the orifice.
A clogged burner tube can lead to a fire beneath the appliance.
All valves must be in the OFF position.
2.
Open cylinder valve.
3.
4.
Ignite only the burners you desire to use, using the same method for each: Push in desired burner valve knob fully and rotate slowly about 1/4
turn counter-clockwise until a click is heard and this will light the burner. If the burner does not light, immediately return the valve knob to OFF,
wait five minutes for the gas to clear and repeat the procedure. After burner ignites, repeat the same procedure with any other burner desired.
5.
Adjust valve knob(s) to desired cooking setting.
Lighting Rod light the Main Burners:
1.
Remove cooking grid from burner you desired to light.
2.
Dip the end of lighting rod into flamable liquid as kerosene then light it. Once lit, place the flame through the hole as shown near the burner ports.
3.
Press in valve knob and rotate counter clockwise to High setting and burner should light immediately. If more than one burner is desired, repeat
procedure with each burner.
4.
Replace cooking grid and adjust burners to desired cooking settings.
Option-Left and right main burners can be lit by inserting a lit match attached to the end of the Lighting Rod
through holes on either side as desired.
After lighting, please observe the burner flame, make sure all burner ports are lighted.
If burner flame goes out during operation, immediately turn the gas "off" and open lid to let the gas clear for about 5 minutes before re-lighting.
Before cooking on this grill for the first time, operate the grill for about 15 minutes with the lid closed and the gas turned on "high." This will "heat clean"
the internal parts and dissipate odor from the manufacturing processes and painted finish.
Clean your grill after each use, DO NOT use abrasive or flammable cleaners, as it will damage the parts of this product and may start a fire.
1. Open lid during lighting burner. Lid must be open when burner is on.
2. Valve must be in the "off" position
3. Open cylinder valve.
4. Push in side burner valve knob fully and rotate slowly about 1/4 turn counter-clockwise until a click is heard and this will light the burner. If the
burner does not light, immediately return the valve knob to OFF, wait five minutes for the gas to clear and repeat the procedure.
5.
After burner ignites, adjust valve knob to desired cooking setting.
Shutting Off Burners
1.
Always turn the valve knob(s) clockwise to the High position, then depress and turn it to OFF.
Never force the knob without depressing it as that can damage the valve.
2.
Promptly turn the gas supply OFF at the propane cylinder.
Close the lid of the grill.
3.
GSC3218J owner's manual
Check For Leaks
Lighting Your Grill
:
Main Burner
Side Burner
14
GSC3218J Gas Grill
Advertisement
Table of Contents
