Summary of Contents for Husky HUG-500S
- Page 1 HUG-500S(E) Industrial 5 10/100/1000TX Gigabit Unmanaged Ethernet Switch User’s Manual V2.0 6-26-2009...
- Page 2 Husky Series Industrial Ethernet Switch Solutions HUG-500S(E) Industrial Gigabit Unmanaged Switch User’s Manual Copyright Notice Copyright © 2009 Ethernet Direct Corp. All rights reserved. Reproduction in any form or by any means without Ethernet Direct prior written permission is prohibited.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Introduction............................1-1 1-1 Overview ............................1-1 1-2 Product Features ........................... 1-1 1-3 Package Checklist ......................... 1-1 Chapter 2 Hardware Installation .......................... 2-1 2-1 Dimensions and Panel Layout ....................... 2-1 2-2 LED Indicators ..........................2-2 2-3 RJ-45 Ports ............................ 2-2 2-3.1 RJ-45 Pin Assignments ........................2-2 2-4 Installing Your Ethernet Direct Switch.................... -
Page 4: Chapter 1 Introduction
Its IP-30 housing protection, wide operating temperature of -10 to 70℃ and DIN-Rail mounting is suitable for an industrial environment. The E version has extended operation temperature range of -40 to 80℃. The HUG-500S is a plug-and-play solution for your industrial Ethernet applications. -
Page 5: Chapter 2 Hardware Installation
Dimensions and Panel Layout LED Indicators RJ-45 Ports Installing Your Ethernet Direct Switch 2-1 Dimensions and Panel Layout Dimensions of HUG-500S(E) Industrial Gigabit Managed Switch are 30mm (W) x 95mm (D) x 140mm (H). Unit: mm Front Panel Side Panel Top Panel... -
Page 6: Led Indicators
Hardware Installations 2-2 LED Indicators There are diagnostic LEDs located on the front panel of HUG-500S(E). They provide primary information on switch status as described in the table below. LED Name LED Color LED Function Green Power input 1 is on. -
Page 7: Installing Your Ethernet Direct Switch
2-4.1.1 DIN-Rail Mounting The DIN-Rail mounting kit is attached to the back panel of HUG-500S(E) by default. If not, or users want to disassemble the DIN-Rail mounting kit from the HUG-500S(E), follow the steps below. - Page 8 Hardware Installations Follow the steps below for mount the switch onto the track. 1. Insert the top of DIN-Rail plate into the track. 2. Lightly push the DIN-Rail plate into the track. 3. Check if the DIN-Rail is tightened on the track or not. 4.
-
Page 9: 2-4.2 Wiring The Power Inputs
Hardware Installations 2-4.2 Wiring The Power Inputs Follow the steps below to wire the power inputs. Be sure to disconnect the power cord before installing and/or wiring your switch. Be sure of the maximum possible current when wiring connections. If the current goes above the maximum ratings, the wire could overheat and result in serious damage to your switch. -
Page 10: 2-4.3 Wiring The Fault Alarm Contact
Hardware Installations 2-4.3 Wiring The Fault Alarm Contact The fault alarm contacts are the two middle terminals located on the terminal block as show in the figure below. It detects errors such as power failure or port break and sends an alarm signal when faults occur. By default, the fault alarm contacts will form an open circuit under normal operation. -
Page 11: Specifications
Specifications HUG-500S(E) Product Specifications are as follows: Hardware Interface RJ-45 Ports 5 10/100/1000Base-TX auto-negotiation speed, Full/Half duplex mode, auto auto MDI/MDI-X connection LEDs Per Unit Power 1 (Green), Power 2 (Green), Fault (Red) Per Port Link/Activity (Green), Speed (1000Mbps Green) - Page 12 Specifications EN61000-4-12 EN61000-6-2 EN61000-6-4 Safety UL, cUL, CE/EN60950-1 Shock IEC60068-2-27 Vibration IEC60068-2-6 Free Fall IEC60068-2-32 Class 1 Divison 2 Pending Pending Environmental WEEE, RoHS MTBF 325,000 hrs based on Mil-Hdbk-217F, GB Warranty 5 years...
-
Page 13: Appendix B Troubleshooting
Troubleshooting Make sure you are using the right power cord/adapter (DC 12-48V). Do not use power adapters with DC output higher than 48V. Or it will short circuit the switch. Select the proper UTP cables to construct your network. Please check that you are using the right cables.