DYNAMIX IP PHONE 510. User manual I、 DYNAMIX IP PHONE 510 Feature ...............4 Appearance........................4 Interfaces...........................4 Electricity characteristic....................5 Software ..........................5 Operating requirement ......................6 Packing List........................6 Installation.........................6 II、 Web Configuration...................7 Access Web setting page ....................7 Network..........................7 2.1、 WAN Configuration................7 2.2、 LAN Config ..................10 VoIP..........................10...
Page 3
Phone Book ..................24 4.11、 Syslog config ..................24 4.12、 Time Set ..................... 26 4.13、 Reboot....................26 III、 Use keypad configure DYNAMIX IP PHONE 510 ........27 Keypad function......................27 Keypad Menu........................28 IV、 POST Mode ....................29 V、 FAQ........................30 Why the settings vanish after reboot? ................30 How to use the dial rule?....................30...
192.168.10.x or using dynamic obtain IP. Open your web browser and key in 192.168.10.1. Then you will see the logon page of DYNAMIX IP PHONE 510, the default username and password is admin/admin for administrator and guest/guest for guest.
II、 Web Configuration Access Web setting page Enter DYNAMIX IP PHONE 510 IP address in the web browser and press ENTER to go to the log on page, and key in the username and password to access DYNAMIX IP PHONE 510 setting page.
Page 8
DYNAMIX IP PHONE 510. User manual Parameters: Active IP: IP phone’s address Current Netmask:network netmask MAC Address:MAC of IP phone Current Gateway : the IP address of the router B、 If your ISP provide you with the fixed IP address, please choose static and fill in the correct information of IP Address、...
Page 9
DYNAMIX IP PHONE 510. User manual Static IP Address: fixed IP address Netmask: LAN netmask Gateway: Gateway IP address DNS Domain: imput DNS domain name if it’s provided Primary DNS: Primary DNS address Alter DNS: Alternative DNS address C、when you use PPPoE to get IP address,please select “PPPoE”,and input ADSL account information as below picture:...
DYNAMIX IP PHONE 510. User manual 2.2、 LAN Config Parameter: LAN IP:config LAN static IP Netmask: LAN netmask DHCP Service: enable LAN DHCP Server , need to reboot to make it available. NAT: Network Address Traslation Bridge Mode: make the IP phone into switch mode , press Apply the IP phone will reboot VoIP 3.1、...
Page 11
Enable Register: Enable or disable registration Advanced SIP setting Register Expire Time: register expire time, default is 600 seconds. DYNAMIX IP PHONE 510 will auto configure this expire time to the server recommended setting if it is different 11 / 32...
Page 12
DYNAMIX IP PHONE 510. User manual from the SIP server. NAT Keep Alive Interval: Co-work with the Auto Detect Server, if Auto Detect Server is enable, DYNAMIX IP PHONE 510 will periodically detect if the SIP server is available according this setting. User Agent::...
DYNAMIX IP PHONE 510. User manual Transport Protocol: choose TCP/UDP Subscribe Expire Time: Subscribe information packet Expire Time: Conference Number: config certain Conference call number Signal Encode: enable signal encryption Rtp Encode: enable voice data encryption Enable Session Timer: enable rfc4028 to refresh the SIP sessions...
DYNAMIX IP PHONE 510. User manual Echo test text: echo test number in text format Refresh time: IAX refresh time Enable Register: enable or disable register IAX(Default Protocol): Set IAX 2 as the default protocol to initial the call ( not answering) , if not the system will choose SIP as default.
4.2、 Digit map Digit map is a set of rules to determine when the user has finished dialing. DYNAMIX IP PHONE 510 support below digital map: End With “#”: Use # as the end of dialing. Fixed Length: The call will be sent out automatically when the length of the number you dial reach the fixed one.
IP phone Auto Answer: Enable/disable auto answer function Accept Any Call: If this option is disable, DYNAMIX IP PHONE 510 refuse the incoming call when the called number is different from DYNAMIX IP PHONE 510’s phone number.
DYNAMIX IP PHONE 510. User manual Any digital call with a certain head number , For example 6. means any incoming number with the 6 as the first number will be refused Limit List: outgoing calls with these phone numbers will be refused...
DYNAMIX IP PHONE 510. User manual Handfree Volume:handfree speaker output volume Ring Volume:ring tone volume G729 Payload Length:config G729 Payload length 4.5、 Config Service Config server is an independent IP phone configuration software which is installed in PC Register status:show the status of registration Server Address:config server IP address...
DYNAMIX IP PHONE 510. User manual Dial-Peer configuration This is the Dial-peer setting page , please refer to “How to make dial plan ?”for reference 19 / 32...
Update 4.6、 Web Update: Update IP phone’s settings or firmware. Firmware file is .z extension when configure file is .cfg extension, DYNAMIX IP PHONE 510 will auto select configure update or firmware update according the extension. 20 / 32...
DYNAMIX IP PHONE 510. User manual 4.7、 TFTP/FTP Update: upload/download the configure file with FTP or TFTP server. or download firmware from FTP or TFTP server Back up configure file to your FTP/TFTP server. Server: FTP/TFTP server address . It can be the format of IP address such as 192.168.1.1 or domain such as ftp.domain.com Meanwhile , it support sub directory such as...
DYNAMIX IP PHONE 510. User manual 4.8、 Auto Provisioning Current Version: the system will display the current version number 。 Server Address: FTP/TFTP server address Username: FTP server user name Password: FTP server password Config File Name: The name of configuration file. Normally users leave it as blank the IP...
DYNAMIX IP PHONE 510. User manual System Manage 4.9、 Account Manage Users can add new account or delete and change existing account Keyboard Password:config password that you use keyboard to access the menu , must be in number User Name:set new account name User Level:set new account level;root can read and change setting,general can only read...
DYNAMIX IP PHONE 510. User manual 4.10、 Phone Book Phonebook Table: shows phonebook detailed information Add Phone Book: add a new record in phonebook Name: nick name of a number ,when the call of this number comes in the LCD will show...
Page 25
DYNAMIX IP PHONE 510. User manual 1-alert 2-critical 3-error 4-warning 5-notice 6-info 7-debug ( can only be displayed in telnet mode) Server IP: Syslog server IP address Server Port:Syslog server port MGR Log Level:config MGR log level SIP Log Level:config SIPlog level IAX2 Log Level:config IAX2log level...
DYNAMIX IP PHONE 510. User manual 4.12、 Time Set Server:type the ip address of time server Timezone:select correct time zone in list box Timeout: longest response time for SNTP Manual Timeset:The time setting Select SNTP: choose SNTP server Daylight:Daylight saving time 4.13、...
DYNAMIX IP PHONE 510. User manual III、 Use keypad configure DYNAMIX IP PHONE 510 Keypad function User can configure DYNAMIX IP PHONE 510 through its keypad. List below is the keypad function Keypad Mode Function/Display Idle mode ---- show current time...
Speed dial key Keypad Menu User may use SET, Menu/ok, Exit, Vol+, Vol- to config DYNAMIX IP PHONE 510 detail setting. Press Menu/ok to enter config mode, and the default password is 123. Below list the keypad menu of DYNAMIX IP PHONE 510...
User can restore the factory setting or upgrade to a new firmware to solve this problem. How to enter safe mode? There will be a schedule bar in the DYNAMIX IP PHONE 510 booting procedure, press # key 29 / 32...
Please go to Config Manage Save Config to save your setting always. How to use the dial rule? DYNAMIX IP PHONE 510 provide flexible dial rule, with different dial-rule configure, user can easily implement the following function: Replace, delete or add prefix of the dial number.
DYNAMIX IP PHONE 510. User manual 8610 xxxxxxxx. Suffix (optional):Configure suffix, show no suffix if not set Instance: 2T rule: If the call starts with 2, the first 2 will be deleted, and the rest number will be sent to private SIP server.
Enable Three Way Call If A is using DYNAMIX IP PHONE 510 talking with B and B want to make conference call with A and B. A just press Hold and dial C’s number . Then press CONF to initiate conference call How to use set the IP type via keypad?...
Need help?
Do you have a question about the 510 and is the answer not in the manual?
Questions and answers