Advertisement
Quick Links
Advertisement
Summary of Contents for Ventur IDEO - 275 Ecowatt
- Page 1 IDEO - 275 Ecowatt Installation Manual...
- Page 2 Before manipulating this device, disconnect the electricity supply. During normal operation, never stop the ventilation system.
- Page 3 General Information High-performance heat recovery dwelling unit Introduction This manual is destined for use with the IDEO 275 Ecowatt high performance heat recovery unit and its This manual is destined for use with the IDEO 275 Ecowatt high-performance heat recovery unit and its peripheral fittings (conduits, inlets, regulators…).
- Page 4 Technical information 2.1 General definition The IDEO 275 Ecowatt provides optimum ventilation for a room with a minimum loss of energy. It extracts air from spaces such as (Bathroom/s WC kitchen and washroom/s or shower room/s and extracts air from spaces such as (Bathroom/s, WC, kitchen and washroom/s or shower room/s, and supplies fresh air into the main rooms (Living rooms, bedroom/s, office, …).
- Page 5 New fresh air inlet: The conduit from the outside is connected here. To avoid condensation, it is recommended to use insulated conduits. The new fresh air inlet should be fitted sufficiently far from any source of strong The new fresh air inlet should be fitted sufficiently far from any source of strong contamination (Trees, combustion fumes, roads …).
- Page 6 Dimensions Central unit: Weight: 51 Kg Remote controls: Programmable module Kitchen boost...
- Page 7 Placement On a vertical wall: Wall bracket It is recommended to locate IDEO in On the floor: heated house space. Otherwise it will be necessary to insulate the condensate drain pipework..
- Page 8 On the floor: An specific kit option Support It is recommended to locate IDEO in heated house space. Otherwise it will be necessary to insulate the condensate drain pipework necessary to insulate the condensate drain pipework. Tube cover:...
- Page 9 DIAGRAM OF STANDARD ASSEMBLY TYPE “DELIVERY” Outlet roof caps CT 150 Kitchen BDOP 125 BDOP 80 Toilets Toilets Air intake plenum Air intake D150 Li i Living/sitting room / itti & Bedrooms PAF 150 Circular Air intake wall hoods PAST Air intake roof D150 10 spigots distributor...
- Page 10 DIAGRAM OF STANDARD ASSEMBLY TYPE “DISTRIBUTION” Outlet roof caps Outlet roof caps Living/ CT 150 sitting room BDOP 125 Kitchen BDOP 125 BDOP D80 RD80 Bedrooms Toilets Toilets BDOP D80 RD80 Air intake D150mm PAF 150 Circular Air intake D150mm PAST Air intake roof hoods D150mm...
- Page 11 Characteristics and electrical connections Connect the supplied cable to the mains, using a hermetic connection box. H05VV-F-5G1 type cable Length 1.2 m Connection box Electrical panel Power supply: Single phase 230VAC-50Hz Electrical protection: Maximum power: 190 Watts 190 Watts Max. ambient temperature: 50º...
- Page 12 .2.3 Controlling the IDEO 275 Ecowatt The IDEO 275 Ecowatt can be controlled from: • A button that enables the boost flow for the kitchen to be timed in ½-hour steps. Service life with normal usage (average 3 times a day) is estimated to be about 4 and a half years. For each operation, a red signal will light up for a few seconds to indicate battery life.
- Page 13 2.2.a . Description of the programming module: 15 13 1 – Adjustment mode using the clock 2 – Programming mode (Automatic 1 – Automatic 2 – Manual) d (A t ti 1 A t ti 2 M 3 – Day of the week 4 –...
- Page 14 2.2.b . Functions of the programming module: (1) • Adjustment using the clock: Navigate with keys 19 or 20 to pictogram 1 showing a clock. Select with key 18 The pictogram will flash Validate with key 18 Select with key 18. The pictogram will flash. Validate with key 18. Adjust the desired hour using keys 19 and 20.
- Page 15 - Auto 2: Working week with three meals per day and the weekend, starting breakfast two hours later. Start Finish Start Finish Start Finish Monday 6:30 7:30 12:00 13:00 19:30 20:30 Tuesday 6:30 7:30 12:00 13:00 19:30 20:30 Wednesday 6:30 7:30 12:00 13:00...
- Page 16 • Conditions for the filter icon to be displayed (12): This icon will be displayed when one or several filters are soiled and it is necessary to clean or replace them. F1 = Blowing filters F 2= Extraction filters The time it takes for the filter to become soiled can be highly variable according to the conditions of use and where the house is located (level of outdoor pollution depending on whether it is an industrial area, near roads or motorways, forest or agricultural areas).