Advertisement
Notes
Further copies of this handbook may be found at http://www.stafford-inst.co.uk/docs/st315/user315.pdf
Page
20
ST315 User Handbook
S
D
TAFFOR
INSTRUMENTS
User Handbook
ST315 Temperature Programmer
Stafford Instruments Ltd.
Tel: +44(0)1785 255588
Fax: +44(0)1785 255589
See separate handbook for Installation Instructions
ST315 User Handbook
© Copyright 2004, 2005 Stafford Instruments Ltd.
ST315
www.stafford-inst.co.uk
email: support@stafford-inst.co.uk
Issue:
1.002
Page 1
Date:
01 Dec 2005
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stafford Instruments ST315
Summary of Contents for Stafford Instruments ST315
- Page 1 ST315 Temperature Programmer Stafford Instruments Ltd. www.stafford-inst.co.uk Tel: +44(0)1785 255588 email: support@stafford-inst.co.uk Fax: +44(0)1785 255589 Further copies of this handbook may be found at http://www.stafford-inst.co.uk/docs/st315/user315.pdf See separate handbook for Installation Instructions Issue: 1.002 Page ST315 User Handbook ST315 User Handbook Page 1 ©...
-
Page 2: At A Glance
Cooling Soaking STEP SEGMENT Heating Delay BACK DOWN ST315 Temperature Programmer COOLING RAMP LAMP SOAK TIME LAMP ºC Cooling Soaking Heating Delay SOAK TEMPERATURE LAMP DELAYED HEATING START LAMP RAMP LAMP Page ST315 User Handbook ST315 User Handbook Page 19... -
Page 3: Other Features
To stop the firing at any time press the START/ STOP key again Keyboard Lock Facility The keys on the ST315 can be locked so that pressing them has no effect. To review firing data press the key to enter the... -
Page 4: Table Of Contents
SWITCH KILN OFF! Firing ............9 Cooling ............13 To reset the ST315 turn off the power to the instrument and have the fault investigated by your installer or kiln service engineer to rectify the fault. Adjusting While Firing....... 14 Error Messages ........... -
Page 5: Turning On
Err2 wiring open circuit. Get thermocouple °C/hr and wiring checked. Have thermocouple Next displayed is the thermocouple type to which the ST315 is set. This hr.min replaced if necessary. thermocouple type setting should match the type of thermocouple fitted to the kiln and can be R, S, K or N type. - Page 6 This will advance the segment and will immedi- ately terminate a paused soak—advancing to the next segment (if any). Changes made to the operation of the ST315 in this way are temporary An ST315 firing segment comprises a ramp followed by a soak period.
-
Page 7: Adjusting While Firing
Altering a program Adjusting While Firing When the ST315 is not firing there are no lamps lit on the mimic panel, the run lamp is off and the display shows the kiln temperature with the °C Firing values can be adjusted while the ST315 is firing. Also there are indicator lit. - Page 8 When the kiln has cooled to less than 40°C the display alternates every 5 seconds between the kiln temperature and End To return the ST315 back to idle condition ready for the next firing press the START/STOP key (or turn off the power to the instrument).
- Page 9 To start a firing press the START/STOP key. The RUN lamp will light. If the ST315 is programmed to heat the kiln at a faster rate than the kiln is To stop the firing prematurely press the START/STOP key again.
- Page 10 Program Record Sheet Program No. Segment Ramp Soak Temp Soak Time Notes °C/hr °C hr.min Page ST315 User Handbook ST315 User Handbook Page 11...
Need help?
Do you have a question about the ST315 and is the answer not in the manual?
Questions and answers
No indications, komplettly DARK....
If your Stafford Instruments ST315 is completely dark with no indications, check the power supply to ensure the device is receiving power. If power is available but the unit remains unresponsive, possible causes could include a blown fuse, power phase failure, or internal damage. You may need to inspect the power connections, replace a faulty fuse, or seek technical support if the issue persists.
This answer is automatically generated