Advertisement
Notes
Further copies of this handbook may be found at http://www.stafford-inst.co.uk/docs/st312/user312.pdf
Page
20
ST312 User Handbook
S
D
TAFFOR
INSTRUMENTS
User Handbook
ST312 Temperature Programmer
Stafford Instruments Ltd.
Tel: +44(0)1785 255588
Fax: +44(0)1785 255589
See separate handbook for Installation Instructions
ST312 User Handbook
© Copyright 2004, 2005 Stafford Instruments Ltd.
ST312
www.stafford-inst.co.uk
email: support@stafford-inst.co.uk
Issue:
1.002
Page 1
Date:
01 Dec 2005
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stafford Instruments ST312
Summary of Contents for Stafford Instruments ST312
- Page 1 ST312 Temperature Programmer Stafford Instruments Ltd. www.stafford-inst.co.uk Tel: +44(0)1785 255588 email: support@stafford-inst.co.uk Fax: +44(0)1785 255589 Further copies of this handbook may be found at http://www.stafford-inst.co.uk/docs/st312/user312.pdf See separate handbook for Installation Instructions Issue: 1.002 Page ST312 User Handbook ST312 User Handbook Page 1 ©...
-
Page 2: At A Glance
Temperature Glaze. Stoneware Glaze is also suitable for Porcelain. DELAYED On Glaze Enamel is also suitable for some enamelling work. START LAMP Heavy Sculpture is also suitable for Terracotta. RAMP 1 LAMP Page ST312 User Handbook ST312 User Handbook Page 19... -
Page 3: Quick Start Guide
To review firing data press the key to enter the The keys on the ST312 can be locked so that pressing them has no effect. programming menu This is an anti-tamper feature used to ensure that the operation of the ST312 or the program data cannot be altered by un-authorised people. -
Page 4: Table Of Contents
Firing ............9 SWITCH KILN OFF! Cooling ............13 To reset the ST312 turn off the power to the instrument and have the fault Adjusting While Firing....... 14 investigated by your installer or kiln service engineer to rectify the fault. -
Page 5: Turning On
Err2 wiring open circuit. Get thermocouple °C/hr and wiring checked. Have thermocouple Next displayed is the thermocouple type to which the ST312 is set. This hr.min replaced if necessary. thermocouple type setting should match the type of thermocouple fitted to the kiln and can be R, S, K or N type. -
Page 6: Programming
As a warning during pause a double PAUSED The ST312 ramps the kiln temperature at ramp rate 1 until the kiln reaches beep is sounded every 10 seconds, temperature t1. It then ramps the kiln temperature to the soak temperature the display scrolls PAUSed for 5 at ramp rate 2. -
Page 7: Adjusting While Firing
Altering the program Adjusting While Firing When the ST312 is not firing there are no lamps lit on the mimic panel, the run lamp is off and the display shows the kiln temperature with the °C Firing values can be adjusted while the ST312 is firing. Also there are indicator lit. - Page 8 Note: to exit programming without cycling through all of the above steps wait 10 To return the ST312 back to idle condition ready for the next firing press seconds without pressing any keys—the ST312 will revert to the idle display.
- Page 9 To start a firing press the START/STOP key. The RUN lamp will light. If the ST312 is programmed to heat the kiln at a faster rate than the kiln is To stop the firing prematurely press the START/STOP key again.
- Page 10 Program Record Sheet Ramp 1 Ramp 2 Soak Temp Soak Time Program Description °C/hr °C °C/hr °C hr.min Page ST312 User Handbook ST312 User Handbook Page 11...
Need help?
Do you have a question about the ST312 and is the answer not in the manual?
Questions and answers