Related Manuals for Zippy Tech. HG2
Summary of Contents for Zippy Tech. HG2
- Page 1 User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 User Manual Product Type: Switching Power Supply Model Name: HG2, HP2, PSM, PSL June 18, 2003 Version 1.0 P/N ??? Page 1/17...
-
Page 2: Table Of Contents
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Table of Contents Safety and Warnings ................3 Product and Accessories...............4 Pin Assignment ..................5 Specification…………………………………………………………..8 Operational Procedures ..............12 Troubleshooting & Maintenance............16 Technical Support ................17 Page 2/17... -
Page 3: Safety And Warnings
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Safety and Warnings IMPORTANT INFORMATION ON SAFETY AND PROPER OPERATION OF THE POWER SUPPLY. << Read the information carefully before using it. >> Do not attempt to take apart the power supply. There are hazardous voltages inside. -
Page 4: Product And Accessories
Note: The above figure is just a sample; please refer to the actual product. Remark: 1. I/O switch on rear panel is only available for HG2 model. 2. The computer case shown above is not part of the power supply. -
Page 5: Pin Assignment
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Pin Assignment Always check the socket and pin assignment (for devices such as motherboard, Hard Disk etc.) before connecting the two heads. O UTPUT OUTPUT COLOR CO LOR O RANGE +3.3V... - Page 6 User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 OUTPUT OUTPUT COLOR COLOR BLACK +12V YELLOW BLACK +12V YELLOW BLACK YELLOW +12V BLACK YELLOW +12V 8 P I N S ( E P S 1 2 V )
- Page 7 User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 OUTPUT COLOR ORANGE +3.3V BLACK 10~12 BLACK 13~15 +12V YELLOW 1 5 P I N S ( S E R I A L A T A H D )
-
Page 8: Specification
Note: The new feature, “Prolonged Cooling” after power supply is remote-off only available on model HG2. Under normal conditions, when power supply is at “Remote-off” mode, cooling fan will remain in operation for the secondary heat dissipation, and will come to stop at a much lower temperature. This will prolong the life of the power supply. -
Page 9: Specifications
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. INPUT CHARACTERISTICS: HP2-6460P/6500P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 8.0 A FOR 115 VAC, 4.0 A FOR 230 VAC. -
Page 10: Output Characteristics
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. INPUT CHARACTERISTICS: PSM-6550P/6600P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 10.0 A FOR 115 VAC, 5.0 A FOR 230 VAC. -
Page 11: Input Characteristics
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. INPUT CHARACTERISTICS: PSL-6701P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 10.0 / 11.0 / 12 A FOR 115 VAC, 5.0 / 5.5 / 6.0 A FOR 230 VAC. - Page 12 User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 INPUT CHARACTERISTICS: PSL-6720P/6800P/6850P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 5A (RMS) FOR 220 VAC 12A (RMS) FOR 110 VAC INRUSH CURRENT: 75A MAX. FOR 110 VAC 150A MAX.
- Page 13 User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 INPUT CHARACTERISTICS: PSL-6A00V VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. STEADY-STATE CURRENT: 14/7A AT ANY LOW/HIGH RANGE INPUT VOLTAGE INRUSH CURRENT: 20A MAX. FOR 110 VAC , 40A MAX. FOR 220 VAC (AT 25 DEGREE C AMBIENT...
- Page 14 User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 INPUT CHARACTERISTICS: PSL-6C00V VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. STEADY-STATE CURRENT: 15/7.5A AT ANY LOW/HIGH RANGE INPUT VOLTAGE INRUSH CURRENT: 20A MAX. FOR 110 VAC , 40A MAX. FOR 220 VAC (AT 25 DEGREE C AMBIENT...
-
Page 15: Operational Procedures
5. Plug in power cord to the inlet of power supply. • Only HG2 models have line power I/O rocker switch. Please set the switch to “I” or “ON” to turn on line power. For other models, just plug the power cord into the electrical outlet directly. -
Page 16: Troubleshooting & Maintenance
AC line source through power bar or UPS, turn on these devices first. If product model is HG2, set I/O switch of power supply panel to “I” or “ON”. Other models HP2, PSM and PSL don’t have line power I/O rocker switch. -
Page 17: Technical Support
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Technical Support To best serve our customers, there are several services available to suite your needs: For detailed products specification: please visit www.zippy.com For technical enquiries: please send e-mail to powersales@zippy.com...