Auto Sp Ep Timer; Auto Timer - JVC HR-VP652U, HR-VP452U Instructions Manual

Auto SP EP Timer

If, when recording in SP mode, there is not enough tape to record
the entire program, the VCR automatically switches to EP mode
to allow complete recording. This feature is especially handy
when recording a program of more than 2 hours in length.
For Example . . .
Recording a program of 140 minutes in length onto a 120-
minute tape
Approximately 110 minutes
SP mode
Total 140 minutes
Make sure you set "AUTO SP EP TIMER" to "ON" at the
Function screen before the timer recording starts.
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS FUNCTION SET
SCREEN
2
Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH 5 ∞ or SHUTTLE PLUS % fi, then press OK
or SHUTTLE PLUS
SELECT AUTO SP EP
TIMER SET MODE
3
HR-VP452U
FUNCTION

AUTO TIMER

SUPERIMPOSE
=AUTO SP = EP TIMER
VIDEO STABILIZER
VIDEO CALIBRATION
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
Move the highlight bar (arrow) to "AUTO SP EP
TIMER" by pressing CH 5 ∞ or SHUTTLE PLUS % fi,
then press OK or SHUTTLE PLUS
RETURN TO NORMAL
SCREEN
4
Press MENU.
NOTES:
If you have programmed the VCR to timer-record 2 or more
programs, the second program and those thereafter may not
fit on the tape if you set the Auto SP EP Timer mode to
"ON". In this case, make sure the mode is not engaged, then
set the tape speed manually during timer programming.
In order to ensure that the recording fits on the tape, this feature
may leave a slight non-recorded section at the end of the tape.
There may be some noise at the point on the tape where the
VCR switches from SP to EP mode.
The Auto SP EP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will work with the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
Approximately 30 minutes
EP mode
.
HR-VP652U
FUNCTION
OFF AUTO TIMER
ON SUPERIMPOSE
= AUTO SP = EP TIMER
ON
OFF VIDEO STABILIZER
ON NEXT PAGE
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
to set to "ON".
Auto Timer
When the Auto Timer is set to ON the timer is automatically
engaged when the VCR's power is turned off. It is automatically
disengaged when the VCR is powered back on.
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS FUNCTION SET
SCREEN
2
Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH 5 ∞ or SHUTTLE PLUS % fi, then press OK
or SHUTTLE PLUS
SELECT AUTO TIMER SET
MODE
3
=AUTO TIMER
SUPERIMPOSE
AUTO SP = EP TIMER
VIDEO STABILIZER
VIDEO CALIBRATION
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
Move the highlight bar (arrow) to "AUTO TIMER" by
pressing CH 5 ∞ or SHUTTLE PLUS % fi , then press OK
or SHUTTLE PLUS
OFF
RETURN TO NORMAL
ON
ON
OFF SCREEN
4
Press MENU.
NOTE:
For safety, when AUTO TIMER is set to "OFF", all other VCR
functions are disabled while the Timer mode is engaged. To
disengage the timer, press TIMER.
.
HR-VP452U
FUNCTION
=AUTO TIMER
OFF
ON SUPERIMPOSE
AUTO SP = EP TIMER
OFF
OFF VIDEO STABILIZER
ON NEXT PAGE
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
to set to "ON" or "OFF".
37
EN
HR-VP652U
FUNCTION
OFF
ON
OFF
OFF