Ultra Steel AP00973S Instruction Manual

4 piece 18 volt cordless power tool combo kit
Hide thumbs Also See for AP00973S:

Advertisement

Available languages

Available languages

THE RBRC
The RBRCTM Seal (Rechargeable Battery Recycling Corporation) on the
nickle-cadmium battery (or battery pack) indicates that the cost of
recycling the battery or battery pack have already been paid by Ultra
Steel. In some areas, it is illegal to place spent nickle-cadmium batteries in
the trash or municipal solid waste stream and the RBRC program provides an environ-
mentally conscious alternative.RBRC in cooperation with Ultra Steel and other battery
users, has established programs in the United States and Canada to facilitate the
collection of spent nickle-cadmium batteries. Help protect our environment and
conserve natural resources by contacting your local recycling center for information on
where to drop o the spent battery, or call 1-877-2-RECYCLE.
FULL ONE YEAR HOME USE WARRANTY
Ultra Steel warrants this product for one year against any defects in material or
workmanship. The defective product will be replaced or repaired at no charge in
either of two ways:
1) Return the product to the store in which it was purchased - this will result in an
exchange only.
Returns should be made within the time frame of the retailer's policy for exchanges
(usually 30 to 90 days after the sale). Proof of purchase is required. Please check with
the store from which your purchase was made to determine policy regarding returns
2) Send the product to Ultra Steel for repair or replacement (whichever Ultra Steel
determines is the best option) and include your proof of purchase.
legal rights and you may have other legal rights which vary from state to state
or province to province. For questions, call Ultra Steel at 1-800-840-7856.
This product is not intended for commercial use.
SERVICE INFORMATION:
For technical advice, repair, or genuine replacement parts,
call 1-800-840-7856 or visit www.UltraSteeltools.com
FREE WARNING LABEL REPLACEMENT:
If your warning labels become illegible or are missing, call 1-800-840-7856 for free
replacement.
Ultra Steel is a registered trademark of and distributed by Test Rite Products
Corporation, 1900 S. Burgundy Place, Ontario, CA. 91761, U.S.A.,
Made in China
SEAL
TM
15
ULTRA STEEL
4
PIECE
1 8
VOLT
Cordless Power Tool Combo Kit

INSTRUCTION MANUAL

AP00973S
CAUTION: Before using this product, read this manual and follow all Safety Rules
and Operational Instructions.
Go to www.ultrasteeltools.com to register your product.
Please read before returning this product to store for any reason.
If you have questions or experience a problem with your Ultra Steel purchase,
go to http://www.ultrasteeltools.com for instant answers 24 hours a day.
If you can't nd the answer or don't have internet access, call 1-800-840-
7856 from 8 a.m. to 5 p.m. Eastern time Monday through Friday.

Advertisement

Table of Contents
loading

Summary of Contents for Ultra Steel AP00973S

  • Page 1: Instruction Manual

    1-877-2-RECYCLE. FULL ONE YEAR HOME USE WARRANTY INSTRUCTION MANUAL Ultra Steel warrants this product for one year against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways:...
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS its intended function. Check for alignment of moving parts, binding of moving operation. Check bits to make sure they are sharp and not chipped. Inspect screws WARNING: When using electric tools, machines or equipment, basic safety and tighten any ones that are loose. Any part that is damaged should be properly precautions should always be followed to reduce the risk of re, electric shock, repaired or replaced by an authorized service center unless otherwise indicated and personal injury.
  • Page 3: Specifications

    SPECIFICATIONS Cordless Sander Model No.: AP00963G Voltage: 18 volts DC Cordless Drill No Load Speed 4400 RPM Trigger Model No.: AP00965G Switch Voltage: 18 volts DC 3-1/2 In. Sanding Pad No Load Speed 0-350/0-1100 RPM Variable Speed Trigger Conforms to UL STD No. 60745-1, UL With Electric Brake Sanding Base STD No.
  • Page 4: Operating Notes For Battery Pack/Drill

    WARNING: Hold power tools by insulated gripping surfaces when performing trash receptacles. an operation where the cutting tool may contact hidden wiring or 11. For use only with Ultra Steel AP00965G -B Ni-cd battery. its own cord. OPERATING NOTES FOR CIRCULAR SAW...
  • Page 5: Operation Notes For Detail Sander/Light

    CHANGING THE BLADE 1. Always grasp the saw with both hands on the handles and push the saw through CAUTION: Do not put hands directly in front of, behind, or below the saw the material. blade when cutting. 2. Be sure there are no nails or any other foreign objects in, on the work piece, or in the 1.
  • Page 6: Parts List For Cordless Drill

    • Keep the tool clean using a soft damp (not wet) cloth. Do not use solvents on the PARTS LIST FOR CORDLESS DRILL plastic parts. • Lubrication is not necessary. After long use, have an authorized service center Item English Name Unit Item English Name...
  • Page 7: Parts List For Circular Saw

    PARTS LIST FOR CIRCULAR SAW Item English Name Unit Item English Name Unit Screw M6x16 Gear box(rear) Upper platen Screw M4x12 Saw blade Small gear Lower platen Motor Screw M4x12 Right housing Adjustable guide Screw ST3.9x16 Spring Motor cover Fixed guide Screw ST3.9x16 Screw M4x12 Wrench...
  • Page 8: Parts List For Cordless Detail Sander

    PARTS LIST FOR CORDLESS DETAIL SANDER PARTS LIST FOR CORDLESS LIGHT Item English Name Unit Item English Name Unit Item English Name Unit Item English Name Unit Logo label Driving gear Housing (support ) Right middle cover Screw Motor Left head cover Battery clip assembly Housing cover Housing support...
  • Page 9 Si usted tiene preguntas o problemas con el Ultra Acero compra, ir a http://www.ultrasteeltools.com para obtener respuestas inmediatas 24 horas al día. Ultra Steel es una marca registrada de y distribuido por prueba Rito Products Corporation, Si usted no puede encontrar la respuesta o no se tiene acceso a internet, llame al 1900 S.
  • Page 10 INSTRUCCIONES 14. EVITAR QUE EL MOTOR ARRANQUE. No llevar herramienta con un dedo en el interruptor. Asegúrese de que el interruptor de dirección está en la posición de PUNTO MUERTO cuando no estén en uso o Al cambiar bits. ADVERTENCIA: Al usar herramientas eléctricas, máquinas o equipos, siempre 15.
  • Page 11 ESPECIFICACIONES CALIFORNIA PROP 65 Y OTRAS ADVERTENCIAS ADVERTENCIA: Algunos polvo creado al lijar, serrado, esmerilado, taladrado y otras Taladro Inalámbrico actividades de construcción contiene sustancias químicas conocidas en el estado de Modelo Número.: Ap00965g California como causantes de cáncer, defectos de nacimiento u otros daños reproducti- Tensión: 18 Voltios Cc vos.
  • Page 12: Especificaciones

    ESPECIFICACIONES NOTAS SOBRE EL FUNCIONAMIENTO DE LA BACTERIA 1. La batería debe estar completamente cargada antes del primer uso. Las baterías Sander Inalámbrico lleguen a pleno rendimiento después de cinco ciclos de carga/descarga. Modelo Número.: AP00963G 2. Siempre tienen rotación interruptor en posición de punto muerto al desmontar o Tensión: 18 voltios CC colocar la batería para evitar que el motor arranque.
  • Page 13 2. Cuando se presiona hacia dentro de la derecha a la izquierda, la rotación es inverso 1. Siempre sujete la sierra con ambas manos sobre las empuñaduras y empuje la sierra a (Contrario a las agujas del reloj). través del material. 3.
  • Page 14: Mantenimiento

    CAMBIO DE LA CUCHILLA MANTENIMIENTO PRECAUCIÓN: no coloque las manos directamente en frente de, detrás de, o ADVERTENCIA: Siempre hay que quitar la batería de sus herramientas por debajo de la hoja de sierra para cortar. sin cable cuando se están armando las piezas, la realización de ajustes, montaje o desmontaje las hojas, la limpieza o cuando no esté...
  • Page 15 SÍMBOLO LISTA DE PIEZAS PARA EL TALADRO INALÁMBRICO ADVERTENCIA: Algunos de los siguientes símbolos pueden aparecer en la Item Nombre en Inglés Unit Item Nombre en Inglés Unit herramienta. Estudio estos símbolos y aprender sus contempladas. de dos bits 13.1 Interruptor Interoeretation adecuada de estos símbolos para permitir más e ciente y clip...
  • Page 16 LISTA DE PIEZAS PARA SIERRA CIRCULAR Nombre en Inglés Unit Item Nombre en Inglés Unit Item Caja de engranajes Tornillo M6x16 Parte trasera) Upper platen Tornillo M4x12 Hoja de sierra Engranaje pequeño Tornillo del Motor Lower platen Caja Derecha Tornillo M4x12 Tornillo ST3.9x16 Guía ajustable Cubierta del motor...
  • Page 17 LISTA DE PIEZAS PARA CORDLES DETALLE SANDER LISTA DE PIEZAS PARA LUZ INALÁMBRICO Item Nombre en Inglés Unit Item Nombre en Inglés Unit Item Nombre en Inglés Unit Item Nombre en Inglés Unit Engranaje de Apoyo de la caja Etiqueta Cubierta intermedia derecha 1 PCS Tapa de culata...

This manual is also suitable for:

Ap00965gAp00964gAp00963gAp00962g

Table of Contents