Specifications - JVC HR-5911U Instructions Manual

C
Select video input connector
Select the appropriate mode depending on the connector being
used ( pg. 16).
When using S-VIDEO input connector on the front panel, set
"FRONT AUX INPUT" to "S-VIDEO".
When using S-VIDEO IN connector on the rear panel, set "REAR
AUX INPUT" to "S-VIDEO".
When using VIDEO input connector on the front panel, set
"FRONT AUX INPUT" to "VIDEO".
When using VIDEO IN connector on the rear panel, set "REAR
AUX INPUT" to "VIDEO".
D
Select edit mode
Set the edit mode to "ON" for the VCRs if such a mode is
equipped.
On this VCR, set "PICTURE CONTROL" to "EDIT" (
E
Locate end point
Load the cassette to be edited into the VCR and press PLAY (4),
then press PAUSE (9) when you find the end of the scene for
which you want to edit.
Press C.RESET so that the counter reading becomes "0:00:00".
F
Locate start point, and engage Insert Editing mode
Press REW ( ), then press PAUSE (9) when you find the
3
beginning of the scene for which you want to edit, then press
INSERT.
The VCR enters the Insert Editing Pause mode. "
light on the display panel.
If you want to perform AV Dubbing and replace the picture,
Hi-Fi audio soundtrack and normal audio soundtrack all at the
same time, after you press INSERT, press A.DUB also.
G
Start editing
Load the source cassette and engage the Play mode of the other
component, then press PLAY (4) on the VCR. Insert Editing begins
at this point.
Insert Editing stops automatically when the counter reaches
"0:00:00", and the VCR enters the Play mode.
To stop editing any time during recording
Press STOP (8) on the Remote or STOP/EJECT (0) on the
VCR, then engage the Stop mode of the other component.
NOTES:
Insert Editing is not possible with a cassette whose record safety
tab has been removed.
The recording speed (SP/EP) is determined by the previous
recording to be replaced. If the recording speed changes on the
tape to be edited while editing the tape, the inserted picture will
be distorted where the recording speed changes.
When you edit a tape, a small portion of the recording
preceding to the editing start point will be erased from the
edited tape.

Specifications

GENERAL
Power requirement
Power consumption
Power on
Power off
Temperature
Operating
Storage
Operating position
pg. 15).
Dimensions (W x H x D) : 435 mm x 94 mm x 247 mm
Weight
Format
Maximum recording time
SP
EP
VIDEO/AUDIO
" and "$" Signal system
Recording/Playback
system
Signal-to-noise ratio
Horizontal resolution
VHS
S-VHS
Frequency range
Normal audio
Hi-Fi audio
Input/Output
TUNER
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
TIMER
Clock reference
Program capacity
Memory backup for timer is not supported.
ACCESSORIES
Provided accessories
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without
notice.
— 20 —
: AC 120 V , 60 Hz
d
: 17 W
: 1.5 W
: 5°C to 40°C (41°F to 104°F)
: –20°C to 60°C (–4°F to140°F)
: Horizontal only
(17-3/16" x 3-3/4" x 9-3/4")
: 2.8 kg (6.2 lbs)
: S-VHS/VHS NTSC standard
: 210 min. with ST-210 video cassette
: 630 min. with ST-210 video cassette
: NTSC-type color signal and EIA
monochrome signal, 525 lines/
60 fields
: DA-4 (Double Azimuth) head helical
scan system
: 45 dB
: 230 lines
: 400 lines
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
: RCA connectors (IN x 2, OUT x 1)
S-video connectors (IN x 2, OUT x 1)
: Frequency-synthesized tuner
: Channels 2–13
: Channels 14–69
: 113 Channels
: Channel 3 or 4 (switchable; preset to
Channel 3 when shipped) 75 ohms,
unbalanced
: Quartz
: 1-year programmable timer/
8 programs
: Infrared remote control unit,
"AA" battery x 2,
S-video cable (4-pin),
RF cable (F-type)