Download Print this page

Advertisement

SERVICE MANUAL
System controller
CONTENTS
SPECIFICATIONS .................................................................... 3
1. DISASSEMBLY ..................................................................... 4
2. ADJUSTMENT ...................................................................... 6
3. REWRITING THE SOFTWARE ............................................ 7
4. PARTS LIST ....................................................................... 10
Product safety should be considered when a component replacement is mand in any area of this unit.
Components indicated by the symbol (
be of special significance. It is particularly recommended that only parts designated on the parts list in this manual be used for
component replacement designated by the symbol. No deviations from resistance, wattage or voltage ratings may be made for
replacement items designated by the symbol.
NOTE: 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N.S.P. : Not available as service parts.
Design and specifications are subject to change without notice.
L8CSB/US,XE
PRODUCT SAFETY NOTICE
) in the parts list and schematic diagram designate components in which safety can
FILE NO.
VSP-8000
(Product Code : 117 523 55)
(U.S.A., Canada)
(Taiwan, Korea)
VSP-8000
(Product Code : 117 523 54)
(Europe)
REFERENCE No.SM5310327

Advertisement

   Also See for Sanyo VSP-8000

   Related Manuals for Sanyo VSP-8000

No related manuals

   Summary of Contents for Sanyo VSP-8000

  • Page 1: Table Of Contents

    FILE NO. SERVICE MANUAL System controller VSP-8000 (Product Code : 117 523 55) (U.S.A., Canada) (Taiwan, Korea) VSP-8000 (Product Code : 117 523 54) (Europe) CONTENTS SPECIFICATIONS ..............3 1. DISASSEMBLY ..............4 2. ADJUSTMENT ..............6 3. REWRITING THE SOFTWARE ..........7 4.

  • Page 2

    - 2 -...

  • Page 3: Specifications

    SPECIFICATIONS Communication method : RS 485 Control terminals : RJ-11:2 terminals Push-lock: 1 pair RS-232C terminal : D-SUB (9-pin): 1 port Address/termination switch : Address: 3-bit DIP switch Termination: 1-bit DIP switch Communication speed (baud rate) : 2400, 4800, 9600, 19200 bps Max.

  • Page 4: Disassembly

    1. DISASSEMBLY 1-1. REMOVAL OF CABINET AND BOARD LOCATION Bottom Cover Shield Case CP-1 BOARD LCD Assy Cabinet TB-2 BOARD Fig. 1 - 4 -...

  • Page 5

    TB-1 BOARD OP-1 BOARD OP-2 BOARD TB-3 BOARD Fig.2 CP-1 BOARD TB-2 BOARD OP-1 BOARD TB-3 BOARD TB-1 BOARD OP-2 BOARD Fig. 3 - 5 -...

  • Page 6: Adjustment

    2. ADJUSTMENT 1. POWER VOLTAGE ADJUSTMENT 3. Push the ENTER button, and set the adjustment mode, and it confirms that it is indicated with "PLEASE SPIN JST AND Measuring Point Measuring Equipment Condition PUSH ENTER" in LCD. 4. It swings, and a circular movement is done about 2-3 laps TP302, POWER ON Digital voltmeter...

  • Page 7: Rewriting The Software

    3. REWRITING THE SOFTWARE 3-1. Setting up the computer RS-232C CONNECTOR RESET BUTTON Use the Hyper Terminal which is compatible with Windows 95 , 98 or other. JK-405 1. Connect the RS-232C connector with the RS-232C con- nector on the computer using an interlink serial interface cable.

  • Page 8

    3-2. Resetting the computer If an rewriting error occurs, close the Hyper Terminal, and then repeat the procedure in 3-1. Setting up the computer from step Initial display mode 3-3. Rewriting data S A N Y O C o n t r o l l e r - - : - - : - - 1.

  • Page 9

    7. Click the Open (O) button on the computer screen. Computer screen The rewriting display appears in the system controller LCD. Send Text File Look in: If the software could not be rewritten, an error code appears in the LCD. If an error occurs, reset the computer (see “3-2.

  • Page 10: Parts List

    4. PARTS LIST CABINET AND CHASSIS PARTS (N.S.P.) L8CSB/US N.S.P.: Not available as service parts.

  • Page 11

    LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION 645 053 1385 ASSY,CASE 645 039 8469 (LIVE) 645 039 9091 BADGE (SANYO) 645 039 8483 (FULL) 645 053 1620 ASSY,TB-2 645 053 1514 (MON2 SPOT) 645 053 1248 SCREW M2*6TP 645 039 8421...

  • Page 12

    ELECTRICAL PARTS Note: 1. Materials of Resistors are abbreviated as follows ; Resistors MT-FILM Metallized Film Resistor MT-GLAZE Metallized Glaze Resistor OXIDE-MT Oxide Metallized Film Resistor 2. Capacitors µ UF : PF : pF 3. Inductors µ UH : MH : mH 4.

  • Page 13

    LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION CN305 645 039 7912 6P CONNECTOR (N.S.P.) C3037 645 039 7462 ELECTRIC,10UF,+,-20%,16V CN306 645 039 7905 3P CONNECTOR (N.S.P.) C3038 645 039 7455 ELECTRIC,100UF,+,-20%,6.3V CN307 645 053 1828 2P CONNECTOR (N.S.P.) C3039 645 039 7547 CERAMIC 0.1UF+80,-20%,50V C3040...

  • Page 14

    LOCATION PARTS NO. DESCRIPTION ASSY,LCD 645 053 1811 (LCD) 629 016 4750 LCD DM1623-7BL3 (MISCELLANEOUS) 645 039 8919 16P CABLE ASSY ACCESSORIES & PACKING MATERIALS 613 196 5065 INSTRUCTION MANUAL(U.S.A. & CANADA) 613 196 5058 INSTRUCTION MANUAL(EUROPE) 645 039 8940 AC ADAPTOR (U.S.A.

  • Page 15: Circuit Diagrams & Printed Wiring Boards

    CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS 1. OVERALL WIRING AND CIRCUIT DIAGRAMS OVERALL WIRING ............................C2 TB-1 BOARD ..............................C2 CP-1 BOARD ..............................C3 OP-1 BOARD ..............................C4 OP-2 BOARD ..............................C5 TB-2 BOARD ..............................C5 TB-3 BOARD ..............................C5 2.

  • Page 20

    JP3001 CN307 C3038 JP3005 JP3006 JP3007 JP3010 JP3013 JP3015 JP3016 JP3017 JP3018 JP3019 JP3020 JP3023 JP3022 JP3024 JP3025 JP3026 JP3027 JP3028 JP3029 JP3030 JP3031 JP3032 JP3033 JP3032 JP3036 JP3038 CN308 JP3040 CN302 JP3041 C3031 JP3042 C3030 JP3044 JP3043 JP3045...

  • Page 21

    JP1002 JP1001 JP1004 JP1003 JP1005 JP1006 JP1008 JP1007 JP1009 JP1010 JP1012 JP1011 JP1014 JP1013 JP1015 JP1017 JP1016 JP1018 JP1019 JP1020 JP1021...

  • Page 22

    SANYO Electric Co., Ltd. Osaka, Japan Apr./’02 Printed in Japan...

Comments to this Manuals

Symbols: 0
Latest comments: