JVC RX-DP20VBK Instructions Manual page 82

4. Press one of the learning buttons, to which you
want to assign a signal from the target remote
control.
The LEARN indicator starts flashing.
• If you have pressed DVD or DVD MULTI in step 3, you can
store the signals into the following buttons:
EFFECT
1 2 3
LIVENESS
4 5 6
7 8 9
/P
10 0 + 10
100 +
RETURN
FM MODE
• If you have pressed PHONO in step 3, you can store the
signals into the following buttons:
• If you have pressed CD, or CONTROL to select "CD DISC,"
in step 3, you can store the signals into the following buttons:
– You can store a different set of signals into the following
buttons separately for "CD" and "CD DISC."
EFFECT
1 2 3
LIVENESS
4 5 6
7 8 9
/P
10 0 + 10
100 +
RETURN FM MODE
• If you have pressed TAPE/MD or CDR in step 3, you can
store the signals into the following buttons:
EFFECT
1 2 3
LIVENESS
4 5 6
7 8 9
/P
10 0 + 10
100 +
RETURN FM MODE
• If you have pressed VCR 1 in step 3, you can store the signals
into the following buttons:
VCR 1
STANDBY/ON
EFFECT
1 2 3
LIVENESS
4 5 6
7 8 9
/P
10 0 + 10
100 +
RETURN FM MODE
79
/ REW PLAY
FF/
DOWN TUNING UP
STOP PAUSE
SET
DVD
MENU
PLAY
TUNING
STOP
/ REW PLAY
FF/
DOWN TUNING UP
STOP PAUSE
PLAY
/ REW FF/
DOWN TUNING UP
REC STOP PAUSE
PLAY
/ REW FF/
DOWN TUNING UP
REC STOP PAUSE
CHANNEL
• If you have pressed TV/DBS in step 3, you can store the
signals into the following buttons:
– By setting the TV operation mode selector
either to "TV" or "CATV/DBS," you can store
a different set of signals into the following
buttons.
TV/CATV/DBS
STANDBY/ON
EFFECT
1 2 3
LIVENESS
4 5 6
7 8 9
/P
10 0 + 10
100 +
RETURN FM MODE
5. While the LEARN indicator is flashing, press the
button on the target remote control.
The signal from the target remote control is sent to this remote
control.
"LEARN OK" appears and the LEARN indicator stops flashing
and remains lit. The target signal is now stored in the button
selected in step 4.
Notes:
• If the LEARN indicator stops flashing before you press the
button on the target remote control, repeat from step 4 again.
• If "ERROR" appears on the display, you have failed in storing
the signal. Try again. However some signals do not match with
this remote control even though this remote control can learn
most infrared signals.
6. • Repeat steps 4 and 5 to store more signals in
the same remote mode (source).
• Repeat steps 3 to 5 to store more signals in a
different remote mode (source).
7. Set the LEARN/TRANSMIT (ZONE 1/ZONE 2)
selector to "TRANSMIT (ZONE 1/ZONE 2)" to
finish the storing procedure.
LEARN TRANSMIT
ZONE 1 ZONE 2
For the Zone 1 operations
Notes:
• The signals stored into this remote control from the target remote
control deviate slightly from the original signals. Since some
components will not accept these deviating signals, you may not be
able to operate those components using this remote control even
though the storing procedure has been successfully finished.
• When replacing the batteries, finish changing them without delay;
otherwise, the stored signals are all erased.
TV
CATV/
DBS
TV/VIDEO
CHANNEL
TV VOL
LEARN
LEARN TRANSMIT
ZONE 2
ZONE 1
For the Zone 2 operations