LG 15LS1R Service Manual page 11

No Item Condition
Option 5
1 2HR-OFF 1
2 TV-LINK-TUNER 0
3 FACTORY-MODE 0
4 CHANNEL-MUTE 1
5. Adjustment Command
5.1. Adjustment Command(LENGTH=84)
No. Adjustment Contents CMD(hex)
1 FACTORY ON
2 FACTORY OFF
3 EEPROM ALL INIT.
4 EEPROM Read
5 EEPROM Write
6 COLOR SAVE
(R/G/B cutoff, Drive,
Contrast, Bright)
7 H POSITION
8 V POSITION
9 CLOCK
10 PHASE
11 R DRIVE
12 G DRIVE
13 B DRIVE
14 R CUTOFF
15 G CUTOFF
16 B CUTOFF
17 BRIGHT
18 CONTRAST
19 AUTO_COLOR_
ADJUST
20 CHANGE_COLOR_
TEMP
21 FACTORY_
DEFAULT
22 AUTO_
INPUTCHANGE
Remark
0 : 2 Hour off option - OFF
1 : 2 Hour off option - ON
0 : EEPROM Write Protection On
1 : EEPROM Write Protection Off
ADR VAL Description
E0 00 00 Factory mode on
E2 00 00 Factory mode off
E4 00 00 EEPROM all clear
E7 00 00 EEPROM Read
E8 00 data EEPROM Write by
some values
EB 00 00 Color Save
20 00 00 – 100 They have different
30 00 00 – 100 range each mode,
90 00 00 – 100 FOS Adjustment
92 00 00 – 100
16 00 00 – FF
18 00 00 – FF Drive adjustment
1A 00 00 – FF
80 00 00 – 7F
82 00 00 – 7F Offset adjustment
84 00 00 – 7F
10 00 00 – 3F Bright adjustment
12 00 00 - 64 Luminance adjustment
F1 00 02 Auto COLOR
Adjustment
F2 00 0, 1, 2, 3 0: COOL
1: NORMAL
2: WARM
3: USER
F3 00 00 Factory mode off
& II_SW is "1"
& Input change to "TV"
F4 00 00 0 : TV
1 : AV1
2 : AV2
3 : Component
4 : RGB
5 : DVI
5.2. EEPROM DATA READ
(1) Signal Table
ST ART 6E A 50 A 84
Delay 100ms
ST ART 6F A D1 A
(2) Command Set
Adjustment Contents CMD(hex)
EEPROM READ
Purpose : To read the appointment Address of E2PROM by
128(80h)-byte
5.3. E 2 PROM Data Write
(1) Signal Table
ST ART 6E A 50
Data_1
A
LEN : 84h+Bytes
CMD : 8Eh
ADH : E 2 PROM Slave Address(A0,A2,A4,A6,A8),
Not 00h(Reserved by BufferToEEPROM)
ADL : E2PROM Sub Address(00~FF)
Data : Write data
(2) Command Set
No. Adjustment contents
1 EEPROM WRITE
2
<Purpose>
1) EDID write : 16-byte by 16-byte, 8 order (128-byte) write
(TO "00 – 7F" of "EEPROM Page A4")
2)FOS Default write : 16-mode data (HFh, HFl, VF, STD,
HP, VP, Clk, ClkPh, PhFine) write
3) Random Data write : write the appointment Address of
E2PROM
5.4. VRAM Read
1) Send CMD(70h) to read Video RAM value from MICOM
And save its value to 128-Bytes Buffer(Common Buffer for
the use of EDID).
ST ART 6F A
2) Delay 500ms(Time to wait and read vZideo RAM from
MICOM)
3) Be transmitted the contents of MICOM's 128-bytes Buffer to
PC.(128th Data is the CheckSum of 127-bytes data : That's
OK if the value of adding 128-bytes Data is Zero)
ST ART
6E A 50 A 84
- 11 -
A 03 A CMD A A DH A A DL
128 Bytes
ADR(hex) ADL(hex)
E7 A0 0 0-Page 0~7F Read
80 0-Page 80~FF Read
A2 0 1-Page 0~7F Read
80 1-Page 80~FF Read
A4 0 2-Page 0~7F Read
80 2-Page 80~FF Read
A6 0 3-Page 0~7F Read
80 3-Page 80~FF Read
A 84+ n A 03 A CMD A A DH
. . . Data_n
A CS A ST OP
CMD(hex) LEN
E8 94
84+n
Data1 . . . Data12 A CS NA
A 03 A 70 A 00 A 00
ST OP
A CS A
Dn A ST OP
Details
A A DL A
Details
16-Byte Write
n-byte Write
ST OP
A CS A ST OP