Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for MasterCraft LASER DISTANCE FINDER/MEASURING TOOL
Summary of Contents for MasterCraft LASER DISTANCE FINDER/MEASURING TOOL
- Page 1 instruction manual LASER DISTANCE FINDER/ MEASURING TOOL 057-4585-0...
- Page 2 Keep this instruction manual for future use. should this product be passed on to a third WARRANTY 23–24 party, then this instruction manual must be included. lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0 lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0...
- Page 3 TYPICAL MEASURING such circumstances, please use a reflector (available separately) when taking measurements. the reflector is a target to be used with the laser Distance Finder/measuring tool to increase ACCURACY ±3 mm* the intensity of the reflected light.
- Page 4 Become familiar with the Laser distance finder/measuring tool this laser distance finder/measuring tool has a built-in laser light. the laser is a class ii and emits Before using this laser Distance Finder/measuring tool, read this instruction manual carefully.
- Page 5 • Keep batteries out of reach of children. • Do not direct the laser distance finder/measuring tool towards the sun or other sources of bright light. this may cause an Error reading or inaccurate measurements. • Do not use the laser distance finder/measuring tool as a leveling tool.
- Page 6 • replace the batteries when the battery Double Pythagorean theorem measurement indicator shows empty. • remove the batteries from the laser distance finder/measuring tool when not using it for minimum measurement indicator extended periods. • the 4 aaa batteries should match each other in brand and type.
- Page 7 2 seconds to turn off the tool. 0' 00" 0.000 ft 0.000 ft 1/16 5. When the laser distance finder/measuring tool is inactive for 5 minutes, it will automatically turn off to save battery power. 0.0 in 0.000 ft 0.000 ft...
- Page 8 • When taking the two measurements, make sure that they are taken from the same starting point (a) and that the second measurement is perpendicular to the target c. taking the measurements correctly will result in the most accurate calculated distance. lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0 lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0...
- Page 9 (locating) is used for transferring measurements, e.g., from indirectly is higher than the measurement position and the other end of that length is lower construction plans. in the continuous measurement mode, the laser distance finder/measuring tool than the measurement position.
- Page 10 Wrong input: the length of one side re-measure; the hypotenuse is of the right triangle as measured is always longer than the first side longer than the hypotenuse. length lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0 lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0...
- Page 11 8. Do not disassemble the laser distance finder/measuring tool; this will expose the user to If the problem remains unsolved after performing the checks described above, call hazardous radiation exposure. the toll-free helpline, at 1-800-689-9928.
- Page 12 Housing assembly 5690181000 seal ring 13 3660407000 spring If any parts are missing or damaged, or if you have any questions, please call the Toll-free Helpline, at 1-800-689-9928. lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0 lasEr DistancE FinDEr/mEasurinG tool - 057-4585-0...
- Page 13 Additional Limitations this mastercraft product is guaranteed for a period of 3 years from the date of original retail this warranty applies only to the original purchaser and may not be transferred. neither the...
Need help?
Do you have a question about the LASER DISTANCE FINDER/MEASURING TOOL and is the answer not in the manual?
Questions and answers