Table of Contents
Advertisement
15.6" LCD Color Monitor
Service
Service
Service
Description
Table of Contents.....................................................1
Revision List................................................................2
Important Safety Notice.............................................3
1. Monitor Specifications................................................4
2. LCD Monitor Description............................................5
3. Operation instructions................................................6
3.1General Instructions...........................................6
3.2 Control buttons................................................6
3.3 OSD Menu.........................................................8
4. Input/Output Specification......................................10
4.1 Input Signal Connector.........................................10
4.2 Factory Preset Display Modes................................10
4.3 Pixel Defect Policy..........................................11
4.4 Failure Mode of Panel .....................................14
5. Block Diagram.................................................15
5.1 Software Flow Chart.............................................15
5.2 Electrical Block Diagram.......................................17
6. Schematic Diagram..................................................19
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2008 Philips Consumer Lifestyle
Page
Page
SAFETY NOTICE
Subject to modification ○
160E1SB/93
160E1SB/97
160E1SB/00
160E1SB/05
160E1SB/62
Description
6.1 Main Board......................................................19
6.2 Power Board...............................................23
6.3 Key Board.........................................................25
7. PCB Layout.........................................................26
7.1 Main Board........................................................26
7.2 Power Board......................................................28
7.3 Key Board.........................................................30
8. Wiring Diagram...................................................31
9. Scalar Board Overview........................................32
10. Mechanical Instructions........................................33
11. Repair Flow Chart...............................................36
12. ISP Instructions...........................................................42
13. DDC Instructions.........................................................45
14. White Balance, Luminance Adjustment..................51
15. Monitor Exploded View................................................53
16. Recommended & Spare Parts List............................54
17. Different Parts List.............................................56
18. General Product Specification................................57
Jan. 12, 2009
K
Chassis: Meridian 1
Page
GB
312278518370
Advertisement
Chapters
Table of Contents
Related Manuals for Philips 160E1SB/93
Summary of Contents for Philips 160E1SB/93
-
Page 1: Table Of Contents
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2008 Philips Consumer Lifestyle Subject to modification ○ Jan. 12, 2009 312278518370... -
Page 2: Revision List
Meridian 1 Revision List Version Release Date Revision History Jan.12.2009 Initial release, Draft Version... -
Page 3: Important Safety Notice
Meridian 1 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 4: Monitor Specifications
Meridian 1 1. Monitor Specifications 1.1 Technical specifications LCD Panel TFT LCD • Type • Screen size 15.6” Visual • Pixel pitch 0.252 x 0.252mm • LCD Panel type 1366 x 768 pixels R.G.B vertical stripe Anti-glare polarizer, hard coated •... -
Page 5: Lcd Monitor Description
Meridian 1 1.2 Physical specifications • Tilt - 5°~ 20° • Power supply 100~ 240 VAC, 50/60Hz • Power consumption <35W (typ.) • Temperature ℃ to 40 ℃ (operating) ℃ to 60 ℃ (storage) • Relative humidity 20% to 80% •... -
Page 6: Operation Instructions
Meridian 1 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (see figure). By changing these setting, the picture can be adjusted to your personal preference. ﹡... - Page 7 Meridian 1 Rear View Kensington anti-thief lock AC power input VGA input...
-
Page 8: Osd Menu
Description of the On Screen Display This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. - Page 9 Meridian 1 The OSD tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.
-
Page 10: Input/Output Specification
Meridian 1 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description Red video input DDC +5V Green video input (SOG) Logic ground Blue video input Ground Sense (GND) Serial data line (SDA) Cable detect (GND) H.Sync/ H +V.Sync Red video ground V.Sync... -
Page 11: Pixel Defect Policy
4.3 Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry’s most advanced manufacturing process and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. - Page 12 In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
- Page 13 Meridian 1 BLACK DOT DEFECTS ACCEPTABLE LEVEL MODEL 160E1 1 dark subpixel 2 adjacent dark subpixels 3 adjacent dark subpixels Distance between two black dot defects * >15mm Total black dot defects of all types TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL 160E1 Total bright or black dot defects of all types...
-
Page 14: Failure Mode Of Panel
Meridian 1 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel. -
Page 15: Block Diagram
Meridian 1 5. Block Diagram 5.1 Software Flow Chat... - Page 16 Meridian 1 1) MCU initializes. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
-
Page 17: Electrical Block Diagram
Meridian 1 5.2 Electrical Block Diagram 5.2.1 Main Board Flash Memory Panel Interface PM25LV010A (CN405) (U402) Scalar IC NT68167FG EEPROM Crystal 12MHz M24C16 (Include MCU, ADC, OSD) (X401) (U407) (U401) H sync V sync D-Sub Connector Keypad Interface (CN101) (CN401) H_Sync VGA_R+ V_Sync... - Page 18 Meridian 1 5.2.2 Power/Inverter Board AC input Bridge Rectifier EMI filter Transformer Rectifier Diodes and Filter Start Circuit: R904、R932 CN902 Feedback Circuit PWM Control IC ON/OFF MOSFET Output Circuit Transformer Lamp Over Voltage ON/OFF Feedback Circuit PWM Control IC Control...
-
Page 19: Schematic Diagram
Meridian 1 6. Schematic 6.1 Main Board 715G3213-F INPUT R101 100R 1/16W 5% H_Sync R102 100R 1/16W 5% HSIN 2 V_Sync R103 100R 1/16W 5% VSIN 2 CN101 R105 R106 C101 2K2 1/16W 5% 2K2 1/16W 5% C102 C103 220pF 22pF C102 C103... - Page 20 Meridian 1 VCC3.3 FB407 ADC_1.8 FB404 300OHM ADC_2.3 120 OHM VCC3.3 DVDD SCALAR DVDD ADC_2.3 CVDD_2.3 C439 C433 C442 C406 ADC_1.8 1uF 10V 0.1uF/16V 1uF 10V 0.1uF/16V CVDD_1.8 U401 C0402 C0402 C431 C430 0.1uF/16V 0.1uF/16V FB405 CVDD_2.3 300OHM CN401 CN402 CVDD_1.8 C401 C406...
- Page 21 Meridian 1 OUTPUT CN405 PANEL_VCC CN403 CN403 PANEL_VCC R434 CN405 220 OHM +-5% 1/4W C420 C419 TCLK1M 0.1uF/16V TCLK1P C420 C421 C441 TCLK1P FB402 TCLK1M Q404 CONN Q405 R415 R433 R434 R435 R436 TCLK1P TCLK1M R433 C419 10K 1/16W 5% 1uF 10V R436 Q405...
- Page 22 Meridian 1 POWER DSUB_5V U406 NC/AP1117E33LA CN404 CN404 BAT54C C422 VOUT D403 D401 5VCC C425 SM240A C426 C427 BKLT-VBRI C428 5VCC BKLT-EN C_PANEL_INDEX D401 Volume D403 Volume# 2 Mute VCC3.3 Q406 R448 NC/100R 1/16W 5% R424 CONN R425 VOUT R426 ADJ(GND) C426 C428...
-
Page 23: Power Board
Meridian 1 6.2 Power Board 715G2852-2 R918 POWER 100 OHM 1/4W L904 R919 +12V 1.0uH 100 OHM 1/4W C912 ZD902 0.001uF C930 RLZ13B R920 C922 R946 100 OHM 1/4W 470PF50V 150 OHM 2W 0.1uF C917 C918 680uF/25V 680uF/25V T901 R943 BD901 Q903 470R 1/8W... - Page 24 Meridian 1 INVERTER CN801 CN802 CONN C839 T801 R821 C801 1500PF/50V POWER X'FMR R817 1K 1/8W 10K 1/10W 1% CN801 C802 R855 D805 C803 15R 1/4W LL4148 C819 C801 C807 F801 0.0022uF 30pF/3KV C817 +12V C819 0 OHM 1/4W C820 C802 R804 Q801...
-
Page 25: Key Board
Meridian 1 6.3 Key Board 715G3016-1 KEY-PAD-SWITCH LED_GRN# LED001 CN001 CN001 R001 4.3K OHM 1% 1/8W C001 C002 LBADC1 R002 2.4K OHM 1% 1/8W C003 LBADC2 DC_POWERON R003 910R 1/8W C004 LED_GRN# C005 LED_RED# R004 4.3K OHM 1% 1/8W C006 C001 C002 C003... -
Page 26: Pcb Layout
Meridian 1 7. PCB Layout 7.1 Main Board 715G3213-F C101 C417 CN404 B1 R110 R424 R451 C102 C419 CN405 A2 R111 R425 R452 C103 C420 D401 R112 R426 R457 C105 C421 D403 R113 R427 R462 C106 C422 FB101 C3 R114 R428 R463 C107... - Page 27 Meridian 1...
-
Page 28: Power Board
Meridian 1 7.2 Power Board 715G2852-3-4 BD901 D4 C940 IC903 C3 J907 C604 CN601 D5 J601 J908 C801 CN602 B5 J602 J909 C802 CN801 A1 J605 J910 C803 CN802 D1 J801 J911 C900 CN901 D2 J802 J912 C901 CN902 A5 J803 J914 C902... - Page 29 Meridian 1 C601 C909 F904 R608 R835 R921 C602 C910 F905 R801 R837 R922 C603 C911 IC801 A2 R802 R839 R923 C606 C912 IC901 C3 R803 R841 R924 C608 C924 JR801 A2 R804 R850 R925 C609 C925 JR902 C3 R805 R851 R926 C610...
-
Page 30: Key Board
Meridian 1 7.3 Key Board 715G3016-1 CN001 B5 GND1 GND2 LED001 B3 SW001 B2 SW002 B3 SW003 B1 SW004 B3 SW005 B4 C001 R002 C002 R003 C003 R004 C004 R005 C005 R007 C006 ZD001 B2 C007 ZD002 B4 C008 ZD003 B1 C009 ZD004 B3 C010... -
Page 31: Wiring Diagram
Meridian 1 8. Wiring Diagram Panel CN902 CN801 24 Pin Power Board CN405 CN404 CN802 Main Board NT68167FG (U401) CN901 CN401 CN101 AC IN D-SUB 7 Pin Key Board CN001... -
Page 32: Scalar Board Overview
32 32 Meridian 1 9. Scalar Board Overview DC-DC Converters Flash ROM NOVATEK Chip... -
Page 33: Mechanical Instructions
Meridian 1 10. Mechanical Instructions 1. Place the monitor face down on a smooth surface .Be careful to avoid scratch and injury during the process of uninstall. 2. Remove three screws to remove the STAND-BASE ASS’Y. 3. Use disassembly tool to open 4 latches at bottom, 4 latches at left, 5 latches at top and 4 latches at right of bezel, and remove bezel. - Page 34 34 34 Meridian 1 4. Remove main frame. A. Disconnect two connectors and four screws. B. Press to release left and right latches of LVDS cable, and then disconnect it. 5. Remove Power Board and Main Board. A. Remove two screws.
- Page 35 Meridian 1 B. Remove three screws to remove the Power Board and Main Board from Main Frame. C. Disconnect three connectors from Main Board.
-
Page 36: Repair Flow Chart
36 36 Meridian 1 11. Repair Flow Chart 11.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section Measure U404 PIN2=3.3V Check C426 and C427... - Page 37 Meridian 1 (2). No Picture No picture X401 oscillate Replace X401 The button if under control Check Correspondent Check reset circuit of component U401 is normal Measure U404 PIN2=3.3V Replace U401 Check C426 and C427 X401 oscillate waveform is normal Replace X401 Check HS VS from CN101 is normal Check Correspondent...
- Page 38 38 38 Meridian 1 (3). White screen White screen Measure Q404 base is low level? X401 oscillate waveform is normal Replace X401 Check Q404, Q405 is broken or CN405 solder? Check reset circuit of U401 is normal Check Correspondent Check Correspondent component.
- Page 39 Meridian 1 11.2. Power/Inverter Board (1) No power Check ZD902 ＝12V Check AC line volt 100V or 240V Check AC input Check the voltage of C907 (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin8 of IC901 Check R904, R932and Change IC901 Check the auxiliary voltage is bigger than 10V and smaller than 16V...
- Page 40 40 40 Meridian 1 (2) W / LED, No Backlight Check ZD902 ＝12V Check adapter or MB Check ON/OFF signal Check Main Board Check IC801 PIN12=12V Check Q805, Q808 Check IC801 PIN8, 9 or PIN10, 11 have the output of square Change IC801 Check Q809 have the output of square wave at short time.
- Page 41 Meridian 1 11.3 Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Replace Button Switch Is Button Switch normally? Replace Key Pad Board Is Key Pad Board normally? Check Main Board...
-
Page 42: Isp Instruction
ISP BOARD x1 b. Printer cablex1 c. VGA cable x1 12.1 Install the “EasyUSB WriterV4.1” 12.2 Connect the ISP board as follow: Connect to Connect to the the PC LPT Philips 160E1 12.3 The process of ISP write is as follows. - Page 43 Meridian 1 a) Double-click ，running the program as follows: b) Click icon and the program runs as follows:...
- Page 44 44 44 Meridian 1 c) Click icon, search the program “Philips_160E1_NT68167_CMO_M156B1L01_20081219_V100”, and click open: Click icon. If it burns successfully, it will show as the follow picture:...
-
Page 45: Ddc Instruction
The process of installing “PORT95NT” has been specified in, so it will not be specified again. If you have any problem, please read it. 13.2 Connect the DDC Board as follow: Connect to the PC LPT When you write analog EDID, Connect this port to the Philips 160E1’s VGA port 12V Input... - Page 46 46 46 Meridian 1 Take analog DDC write for example, as follow a. Double-click ，appear as follow Figs：...
- Page 47 Meridian 1 b. Click c. Click , and key in 14 numbers in the Serial Number Blank, then click “OK”, Now analog DDC Write complete, as follow:...
- Page 48 48 48 Meridian 1 160E1 EDID 128 bytes EDID Data (Hex): x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 00 FF FF FF FF FF FF 00 41 0C 2D C0 B8 B6 01 00 10: 17 0B 01 03 68 22 13 78 2A B3 70 A2 55 48 98 27 20: 15 50 54 BF EE 00 31 0A 61 4C 01 01 01 01 01 01 30: 01 01 01 01 01 01 7F 21 56 AA 51 00 1E 30 46 8F...
- Page 49 Meridian 1 Composite Sync Support: No Sync. on green video supported:No Serration of the Vsync.Pulse is not required. Max. H. Image Size: 34cm. Max. V. Image Size: 19cm. Display Gamma: DPMS Features, Stand-by: No. DPMS Features, Suspend: DPMS Features, Active off: Yes.
- Page 50 Detailed Timing: 1366x768 @ 60Hz <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '123312311231' Detailed Timing: FC (Monitor Name) 'Philips 160E' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30 KHz Max.
-
Page 51: White Balance, Luminance Adjustment
Meridian 1 14. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS 160E.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing b. - Page 52 52 52 Meridian 1 4. Color Temp confirmation Connect the signal to the monitor, the monitor displays white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC.
-
Page 53: Monitor Exploded View
Meridian 1 15. Monitor Exploded View... -
Page 54: Recommended & Spare Parts List
FQ003 PWPC8521MQCU POWER BOARD ASSY SCALER BOARD（CBPCRNFPHQ2） FQ002 756GQ8CB PH004 FQ105 Q34G0274AFL 2B0100 REAR COVER15.6" FQ103 705GQ834603 15.6"PHILIPS STAND-BASE ASS'Y E08902 089G 725CAA DB D-SUB CABLE FQ301 089G414A15N IS POWER CORD FQ303 095G8018 3DH45 LVDS CABLE 30P-24P 120mm FQ205 705GQ9CS001... - Page 55 056G 563 52 IC AP1117D33L-13 TO252-3L U102 056G 662 13 IC AZC099-04S SOT23-6L U103 056G 662 13 IC AZC099-04S SOT23-6L U402 100GPNM6000NT1 MCU ASSY(056G1133713) Service Kit Description Part No. Philips 12NC Picture DDC KIT 715G2005C2 996500043197 NOVATEK ISP KIT 715LT035A 996500043198...
-
Page 56: Different Parts List
56 56 Meridian 1 17. Different Parts List Diversity of 160E1SB/97 compared with 160E1SB/93 160E1SB/97 160E1SB/93 Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description FQ301 089G404A15N IS POWER CORD 089G414A15N IS POWER CORD FQ202 Q44G6004813 1A 15.6 LCD PHILIPS CARTON Q44G6004813 2A 15.6LCD PHILIPS CARTON... -
Page 57: General Product Specification
5.7 FIRE ENCLOSURE REQUEST 5.8 RESINS 5.9 IF PAINT IS USED 5.10 PLASTIC MOLD TOOLING 5.11 PLASTICS FLAMMABILITY 5.12 TEXTURE/GLOSSING OF HOUSING 5.13 TILT AND SWIVEL BASE 5.14 KENNSINGTON LOCK 5.15 LABEL 5.16 PRODUCT DIMENSION/WEIGHT (REFER TO PHILIPS APPROVED SHT 191/SHT560) - Page 58 6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT 6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT RELIABILITY 7.1 MEAN TIME BETWEEN FAILURES QUALITY ASSURANCE REQUIREMENTS 8.1 ACCEPTANCE TEST PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLITY 10. REGULATORY COMPLIANCE 10.1 WORLDWIDE REGULATORY 10.2 EMC REQUIREMENTS 10.3 ROHS 10.4 WEEE...
-
Page 59: Foreword
30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in Philips styling cabinet which has an integrated tilt base. Tier1: CMO Type NR. -
Page 60: Electrical Characteristics
60 60 Meridian 1 3. ELECTRICAL CHARACTERISTERS Interface signal D-sub analog Input signal :Video, Hsync, Vsync Video :0.7 Vp-p, input impedance, 75 ohm @DC Sync: Separate sync TTL level, input impedance 2.2K ohm terminate Hsync Positive/Negative Vsync Positive/Negative Composite sync TTL level, input impedance 2.2k ohm terminate (Positive/Negative) Sync on green video : 0.3 Vp-p Negative (Video 0.7 Vp-p Positive) -
Page 61: Timing Requirement
_ 2008041 OSD TREE PHILIPS OSD Tree-081022.xls Power On Logo: Power On Show up Philips logo 3 seconds Change to input signal. POWER ON LOGO 1366x768.bmp This picture is reference only. The official drawing will send out by PM. -
Page 62: Horizontal Scanning
1366x768 Horizontal Frequency Range 30~60 KHz SI to feedback Vertical Frequency Range 56~76Hz SI to feedback Monitor Name (13 characters max.) Philips 160EW Hot-key definition HOT KEY.xls Any deviation between document and sample, please refer to Philips approved sample. -
Page 63: Visual Characteristics
Meridian 1 4. Visual characteristics Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal: As defined in 3.3, 1366*768 non-interlaced mode (1366*768@60Hz 85.5MHz), signal sources must have 75 ohm output impedance (2) Luminance setting: controls to be set to 300 nits with full screen 100 % duty cycle white signal (3) Warm up: More than 30 minutes after power on with signal supplied. -
Page 64: Mechanical Characteristics
= 0.329 ± 0.015 5. Mechanical characteristics Cosmetic Philips ID Mechanical data files ProE files required Location of Philips Logo Per Philips make-up sheet Gap between panel and front bezel < 1.4mm (Max.) Location of Control Icons Per Philips Graphic sheet... -
Page 65: If Paint Is Used
• All major plastic parts (bezel, back cover) need to be molded from same resin • Plastic resin type selection should be referred to “plastic-Philips Pool monitor” Texture/Glossing of housing • The texture area and texture no should follow Philips make-up sheet. -
Page 66: Label
Carton label should follow Philips requirement. • Regulatory label follow Philips requirement • China RoHS label • Detail document refer to Philips Engineering Reference Book Product dimension / Weight (Refer to Philips approved SHT 191/SHT560) • Unit dimension : 439(w)*363(H)*191(D) • Packed unit dimension: :490(w)*375(D)*145(H) •... -
Page 67: Environmental Characteristics
Meridian 1 Transportation request for EU A. Land 45‘ Truck and Trailer (800X1200mm pallet) B. Land 45‘ Truck and Trailer (1000X1200mm pallet) for UK (update SHT560) 6. Environmental characteristics The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device. -
Page 68: Philips' Flat Panel Monitors Pixel Defect Polity
68 68 Meridian 1 9. Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL Model 160E1 1 lit sub-pixel 2 adjacent lit sub-pixels 3 adjacent lit sub-pixels (one white pixel) Distance between two bright dot defects* ≧25mm... - Page 69 Meridian 1 Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level) Fig 3: Cross talk Pattern Center at Gray level 0 (Black)
-
Page 70: Regulatory Compliance
EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery which also has to meet Philips' immunity testing specification. RoHS Restriction on the use of certain hazardous substances: Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Bipheny1 (PBB) and Polybrominated Bipheny1 Ether (PBDE)(flame retardant). - Page 71 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.