JVC 0209RYMMDWDAT Instructions Manual page 8

Listening to FM and AM Broadcasts
Selecting AM Tuner Interval Spacing
(on the System only)
Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. Before operating the tuner, select the
appropriate AM tuner interval spacing used for your area.
• You cannot change the AM tuner interval spacing while the ECO (Ecology) Mode is activated.
Select AM as the source.
1
2 Turn off (standby) the System.
3 Press and hold to change the AM tuner interval spacing.
Basic Tuner Operations
To Press Indication/Result
Select FM or AM Press repeatedly.
• The selected frequency band appears.
Select a frequency Press and hold for more than 2 seconds.
The System starts searching for stations and stops when a station of
sufficient signal strength is tuned in.
or
• Press during searching to stop.
• Press repeatedly to change the frequency step by step.
Tune in to a preset station Press repeatedly to select its preset number.
• For presetting stations, see
below.
or
Change the FM reception Press to improve reception.
mode The (mono) indicator lights up.
(When an FM stereo Stereo effect will be lost.
broadcast is hard to receive) To restore the stereo effect, press again. The (stereo) indicator lights up.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
1 Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry mode.
2
• Finish the following steps while the indication on the display is flashing.
3 Press to select a preset number for the station you want to store.
or
4 Press to store the station.
Recording Operations
Before You Start recording
Press to start recording.
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent
(On the System)
of the owner of copyright in the sound or video recording, ALL REC
broadcast or cable program and in any literary, dramatic,
musical, or artistic work embodied therein.
• The recording level is not affected by the volume.
• Hyper Bass Sound and Sound Turbo (see page 3) do not
READ USB
affect recordings.
• You can record up to 999 tracks per group to the USB
mass storage class device. If you try to record a track after
recording 999 tracks, "FILEFULL" appears on the display
and the track will not be recorded.
R01 00:01
• The tracks which are recorded to the USB mass storage
class device will be converted into MP3 format (bit rate:
Both recording and playback start at the
128 kbps).
same time.
• You cannot start recording into a USB mass storage class
When playback ends, recording also stops.
device while "READING" is shown on the display.
• Do not disconnect a USB mass storage class device while • If you have programmed the playing order for CD (see
playing or recording. It may cause malfunction. "Programming the Playing Order—Program Play" on page
• During recording, the Random Play and Repeat Play will be 4), the tracks are recorded in the programmed order if
cancelled. Program Play is activated.
• To stop recording manually, press 7.
About SCMS (Serial Copy Management System)
To record the playing track
The System uses the Serial Copy Management System which
allows only first-generation digital copies to be made of
Press to start recording while playing
premastered software such as regular CDs.
back the track to record.
If you try to record from a duplicated disc into the USB mass
storage class device, "SCMS VLT" appears on the display.
To erase tracks/groups
1st generation
2nd generation You can erase tracks/groups on the USB mass storage class
device.
• Once the tracks are erased, you cannot recover them.
• To quit erasing, press 7.
1 Select a track/group you want to erase while playback
is stopped. (See page 4.)
2
3 Select the target to erase.
TTL DEL: Delete a track.
or
GRP DEL: Delete a group.
DEL ALL: Delete all tracks.
Recording from a Disc
4
You can record tracks digitally from a CD onto the USB mass
storage class device.
• Do not vibrate the System while recording tracks. It may
DEL NO:
5
damage the recorded tracks.
or
DEL YES: Continue erasure.
6
Listening to Other Equipment
Front view
Stereo mini plug cord
(not supplied)
To Preset the Audio Input Level
1 Turn the volume to minimum.
If the sound from the equipment connected to the AUDIO
IN jack is too loud or too quiet, you can change the audio
input level through the AUDIO IN jack (without changing the
volume level).
2 Press to select "AUDIO IN."
3
Start playing the connected equipment.
4 Adjust the volume.
5
Setting the Clock and Using Timers
Setting the Clock Setting the Daily Timer
Without setting the built-in clock, you cannot use Daily Timer. Using Daily Timer, you can wake up with your favorite music.
• To go back to the previous step, press CANCEL. • You can store three Daily Timer settings; however, you can
activate only one of the Daily Timers.
1 Press to activate the clock
• To correct a misentry during the process, press CANCEL. You
setting mode.
can return to the previous step.
1
00:00
2 Adjust the hour, then the
or
minute.
2
3
Setting the Sleep Timer
Press repeatedly to specify the time (in minutes)
as follows:
(canceled)
The SLEEP indicator lights up and the display
dims.
To check the remaining time until the System shuts off,
press SLEEP once.
4
Turning Off the System Automatically
—Auto Standby function
(only for Disc/USB)
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
* If no preset channel is stored, "NOMEMORY" appears. When the
• The A.STBY indicator starts flashing after
on time comes, the System tunes in to the station last tuned in.
playback stops.
To exit from the timer setting, press TIMER as required.
If no operation is done for about 3 minutes,
the System turns off.
To Turn Off the Daily Timer
To cancel this function, press the button again.
1
2
To turn on the Daily Timer again, select one of the timer
Cancel erasure.
settings by pressing TIMER, then press SET.
6
Learning More about This System
Basic and Common Operations (see page 3)
• Pressing one of the source buttons also turns on the System
Digital Audio Player, etc.
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
Playing Back a Disc/USB Mass Storage Class Device
(see page 4)
• This System cannot play "packet write" discs.
• For MP3/WMA playback...
– In this manual, "file" and "track" are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
To audio output (or
regular CDs. (It depends on the complexity of the group/
headphone out, etc.)
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
Press repeatedly to select the level as follows:
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
NORMAL: Ordinary input level.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
HIGH: Increases the input level.
(group) does not include MP3/WMA tracks, they are
ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
Troubleshooting
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
Press repeatedly to select one of the timer
finish.
you want to set—TIMER-1, TIMER-2, or
\ There is a time limit. Repeat the procedure again.
TIMER-3.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
Canceled
and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
1 Adjust the hour then the minute for
No sound is heard.
on-time.
\ Speaker connections are incorrect or loose.
2 Adjust the hour then the minute for
\ Headphones are connected.
off-time.
or
3 Select the playback source—"TUNER The System does not work properly.
\ Many functions of this System are implemented by
FM," "TUNER AM," "AUDIO IN," "DISC," or
"USB HOST." microcomputers. If the System does not work correctly,
4 For "TUNER FM" or "TUNER AM": disconnect the AC power cord from the wall outlet, wait
Select a preset channel.* for a while, and connect the cord again.
For "DISC" or "USB HOST": Select a
track. (For MP3/WMA: Select the group, Disc/USB Mass Storage Class Device Operations
then the track number.)
The disc/USB mass storage class device does not play.
5 Select the volume.
\ The disc is placed upside down. Place the disc with the
Turn off the System (on standby). label side up.
\ The USB mass storage class device is not connected
• When the on-time comes, the System
starts playing the specified source and properly.
sets the volume gradually to the preset
MP3/WMA groups and tracks are not played back as you
level.
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
Press repeatedly to select "TIMER-1,"
USB mass storage class device.
"TIMER-2," or "TIMER-3."
Sounds from USB mass storage class device are interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
• For the USB mass storage class device playback...
Display Information
– When connecting a USB mass storage class device, also
refer to its manual.
Play mode indicators (See page 4.)
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
Source indicator
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
REC indicator
• This System can recognize up to 255 groups in a disc. The (See page 6.)
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
File type indicators
(with a maximum number of 255 tracks in a group) in a USB
(See page 4.)
mass storage class device.
• Prohibiting disc ejection (or canceling it) is not available
when the display is turned off ("DISP OFF") or the ECO Mode
is activated ("ECO ON") (see page 3).
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
7
Maintenance
To get the best performance of the System, keep your discs
Radio Operations
and mechanism clean.
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System. Handling discs
\ The FM antenna is not properly extended and positioned. • Remove the disc from its case by holding it at the edge
\ Electrostatic discharge from your body may cause noise. If while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
this happens, turn off and on the System again.
disc.
• Put the disc back in its case after use.
Recording and Editing Operations
• Be careful not to scratch the surface of the disc when
Unable to record into the USB device.
placing it back in its case.
\ The capacity of the USB device is full. Erase some tracks.
• Avoid exposure to direct sunlight, temperature extremes,
\ You have recorded 999 tracks or groups on the USB mass
and moisture.
storage class device. Erase unwanted tracks.
\ The USB mass storage class device is write-protected.
To clean the disc:
\ The USB mass storage class device you connected is
• Wipe the disc with a soft cloth in a straight line from center
incompatible to this System.
to edge.
Display Messages for Recording Operations
Cleaning the System
NODEVICE
• Stains should be wiped off with a soft cloth. If the System is
• No USB mass storage class device is connected or
heavily stained, wipe it with a cloth soaked in water-diluted
the connected USB mass storage class device is not
neutral detergent and wrung well, then wipe clean with a
compatible with this System.
dry cloth.
D. (data) FULL
• Since the System may deteriorate in quality, become
• The capacity of the USB mass storage class device is full.
damaged or get its paint peeled off, be careful about the
FILEFULL
following:
• The USB mass storage class device has exceeded the
– DO NOT wipe it with a hard cloth.
maximum number of files it can support.
– DO NOT wipe it strongly.
W. (write) PROT
– DO NOT wipe it with thinner or benzine.
• The USB mass storage class device is write-protected.
– DO NOT apply any volatile substance such as insecticides
SCMS VLT (violation)
to it.
• You have tried to copy from a duplicated disc to the USB
– DO NOT allow any rubber or plastic to remain in contact
mass storage class device.
for a long time.
D. (device) FAIL
• The System failed to read the USB mass storage class
device.
JVC bears no responsibility for any loss of data in USB mass
Timer Operations
storage class device while using this System.
Daily Timer does not work.
\ The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
8
HBS indicator (See page 3.)
S.TURBO (Sound Turbo) SOUND indicator
indicator (See page 3.) (See page 3.) Source indicators
FM reception indicators
(See page 5.)
Timer mode indicators
(See page 6.)
Main display A.STBY (Auto Standby) SLEEP indicator
indicator (See page 6.) (See page 6.)
Specifications
Amplifier section
OUTPUT POWER:
120 W (60 W + 60 W) at 8 Ω (10% THD)
Speakers/Impedance: 8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at "NORMAL")
250 mV/47 kΩ (at "HIGH")
Digital input: USB REC/PLAY
Tuner section
FM tuning range: 87.50 MHz – 108.00 MHz
AM tuning range: 531 kHz – 1 710 kHz (at 9 kHz
spacing)
530 kHz – 1 710 kHz (at 10 kHz
spacing)
Disc player section
Dynamic range: 80 dB
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
USB storage
USB specification: Compatible with USB 2.0 Full
Speed
Compatible device: Mass storage class
Compatible file system: FAT16, FAT32
Bus power supply: DC 5 V 500 mA
General
Power requirements: AC 110 V – 240 V , 50 Hz/60 Hz
Power consumption: 36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
Dimensions (approx.): 165 mm x 250 mm x 272 mm
(W x H x D)
Mass (approx.): 3.5 kg
Speakers
Speaker units: 4 cm cone x 1
12 cm cone x 1
Impedance: 8 Ω
Dimensions (approx.): 140 mm x 250 mm x 183 mm
(W x H x D)
Mass (approx.): 1.8 kg each
Specifications and appearance are subject to change without
prior notice.