Page 1
Connevans.info Solutions to improve the quality of life This product may be purchased from Connevans Limited DeafEquipment.co.uk secure online store at www.DeafEquipment.co.uk...
Page 2
User Manual COMBINED STROBE & VIBRATING PAD W2-SVP-630 Please read me – as I could save your life. Please retain this user manual for future reference...
Page 3
Keeping you safe from fi re and carbon monoxide For a full range of smoke alarms and carbon monoxide alarms visit www.fi reangel.co.uk...
INTRODUCTION In addition to the audible sound from the Smoke (or CO) alarm, the flashing Strobe and Vibrating Pad will be IMPORTANT: If you are installing this product for triggered to alert someone who may not be able to hear use by others, you must leave this manual (or a the audible alarm.
Page 6
• Designed for use with Smoke alarms and Carbon The Wi-Safe 2 product range is currently being Monoxide alarms from the Wi-Safe 2 range expanded. Please visit www.fireangel.co.uk for (purchased separately). details of the latest additions to the portfolio. Wi-Safe 2 Strobe and Vibrating Pad Pack contains: 1.
INSTALLING THE STROBE CONNECTING THE AND VIBRATING PAD BATTERY/MAINS POWER PREPARATION: Please ensure you have read and NOTE: The Strobe and Vibrating Pad requires both a understood this entire manual before installing your Strobe continuously powered AC (mains) electrical supply and Vibrating Pad.
Page 8
2. Remove the battery cover on the back of the Strobe 6. Plug the power cable in to the Strobe. Route the by pulling back the clip to release. Connect the wire through the wire guide (fig3). rechargeable battery, by aligning the terminals 7.
WIRELESSLY INTERLINKING 3. After pressing this button, the two Alarm (red) LEDs on the front of the unit will flash and then illuminate THE WI-SAFE 2 STROBE AND for 5 seconds. VIBRATING PAD TO YOUR 4. During this period, while the red LEDs are WI-SAFE 2 SMOKE OR CO ALARM illuminated, press the test/reset button on the Smoke or CO alarm to wirelessly interlink the two...
Page 10
NOTE: The battery is supplied in a discharged or To remove (“unlearn”) the Strobe from the wireless partially discharged state and will require up to 24 network: hours of charging (continuous connection to the 1. Briefly push and release the learn button located in mains supply) to ensure that it is fully charged.
TESTING THE WI-SAFE 2 STROBE Strobe: The strobe will flash and the corresponding red (alarm) LED will also flash AND VIBRATING PAD WITH SMOKE/CO ALARMS Vibrating Pad: The Vibrating Pad will vibrate. Repeat the procedure with all alarms in the wireless Testing the network from the Smoke Alarm or CO network.
In addition the network should also be tested whenever: always test your Strobe and Vibrating Pad and all alarms in the Wi-Safe 2 network system every week to ensure • An additional alarm or ancillary product is added to the whole system is in full working order and that the the system wireless interlink (RF) between the alarms and ancillary •...
Page 13
It is important that if you install additional Strobes and placed securely and cannot fall out – ideally within the Vibrating Pads you test each of these upon installation pillowcase or cushion cover. to check they are “learned in” to the rest of the network. Position the Strobe: Wireless Range: The wireless range of Wi-Safe 2...
INSTALLING THE STROBE If placing the Strobe on a table instead of mounting on the wall, Make sure the Strobe is visible from anywhere in make sure it cannot be easily the room. knocked or slide off. The green ‘Power’ should illuminate To wall mount the Strobe drill two suitably sized holes...
LIMITATIONS DANGER: Under no circumstances should this product be immersed in water, or used in an area where water NOTE: This Strobe and Vibrating Pad is not compatible may come into contact with the product. with products from the original Wi-Safe product range. OPERATION •...
LED will flash. operate for three days. NB: Only use the battery supplied in the pack or a genuine FireAngel replacement. Other NOTE: The Strobe will stop flashing, the red LED will rechargeable batteries may damage the equipment or cease to flash and the Vibrating Pad will stop vibrating create a safety hazard.
PRODUCT INDICATORS (LEDS) STROBE/PAD POWER SMOKE FAULT ACTION STATUS ACTIVITY GREEN AMBER NEEDED Standby mode Illuminated None required Mains not connected Double flash every Reconnect Strobe or on battery five seconds to mains power power Vibrating pad Illuminated Reconnect Flashing once per not connected to (providing Strobe is vibrating pad to...
STROBE/PAD POWER SMOKE FAULT ACTION STATUS ACTIVITY GREEN AMBER NEEDED Illuminated Contact technical Unit fault (providing Strobe is Flashes rapidly support plugged into mains) Ensure every alarm and WiSafe Double flash every Network fault 2 device is fitted 1 sec correctly and working Follow learn in...
WHAT TO DO IN THE EVENT OF A • Keep doors and windows closed. Open them only if you have to in order to escape. SMOKE ALARM TRIGGERING THE • Meet at your planned meeting place after leaving the STROBE AND PAD house.
Contact your local fire service. They will give you more What to do during an alarm ideas about how to make your home safer from fires • Keep calm and open the doors and windows to and how to plan your family’s escape. ventilate the property •...
REPAIR The battery provided has been chosen specifically for this application but will need to be replaced every 5 WARNING: DO NOT attempt to repair your Strobe years under normal operating conditions. If during and Vibrating Alert System. Your Wi-Safe 2 Strobe and normal operation (i.e.
TROUBLESHOOTING The Vibrating Pad does not vibrate when test- Check the Vibrating Pad is correctly connected to the Strobe. If it ing. is correctly connected and the Fault (amber) LED is flashing after 2 minutes, contact Technical Support on 0800 141 2561. The Strobe is connected to the Power Supply Check the power supply is plugged in and switched on at a but the Power (green) LED is not illuminated...
Wi-Safe 2 Strobe and etc.). It does not apply to retail stores, service centres Vibrating Pad alert (W2-SVP-630) be free from defects or any distributors or agents. Sprue Safety Products Ltd in materials and workmanship under normal residential...
Except to returned for testing. To return your FireAngel Strobe the extent prohibited by applicable law, any implied and Vibrating Pad under warranty, send it suitably warranty of merchantability or fitness for a particular packed with the battery disconnected with postage purpose is limited in duration for 5 (five) years.
Page 25
Technical Support Line 0800 141 2561 UK Textphone users dial 18001 0800 141 2561 EIRE dial 1-800 523171 Email technicalsupport@fireangel.co.uk www.fireangel.co.uk W2-SVP-630 A Sprue Safety Products Brand Sprue Safety Products Ltd. GN2237/R2 Vanguard Centre, Sir William Lyons Road, Coventry CV4 7EZ UK...