Fortinet FortiWiFi 60CM-3G4G Quick Start Manual page 22

This equipment complies with ACTA TIA-968-A and TIA-1096 and Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the base of this equipment is a label that contains, among other
information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company.
This equipment uses the following USOC jacks: RJ11C
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the total REN, contact the local telephone company.
The REN for this product is separately shown on the label and also part of the product identifier that has
the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g.,
03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required until the problem is resolved. But if advance
notice is not practical, you will be notified by the telephone company as soon as possible. You will be
advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company
may make changes in its facilities, equipment, operations or procedures that could affect the operation
of the equipment. If this happens the telephone company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service.
The telephone company may ask that you disconnect this equipment from the network until the problem
has been corrected or until you are sure that the equipment is not malfunctioning.
If you experience trouble with this equipment, or repair or warranty information, please contact the following
address and phone number for information.
Fortinet Inc.
1090 Kifer Road, Sunnyvale, CA 94086 USA
1-866-393-9960 (US and Canada)
1-613-725-2466 (International)
It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is
connected. This is to avoid damaging the equipment caused by local lightening strikes and other electrical
surges.
This equipment may not be used on coin service provided by the telephone company. Connection to party
line service is subject to state tariffs.
Grounding
Ensure your Fortinet product is connected and properly grounded to a lightning and surge protector. WAN
or LAN connections that enter the premises from outside the building should be connected to an Ethernet
CAT5 (10/100 Mb/s) surge protector.
Shielded Twisted Pair (STP) Ethernet cables should be used whenever possible rather than Unshielded
Twisted Pair (UTP).
Do not connect or disconnect cables during lightning activity to avoid damage to your Fortinet product
or personal injury.
Electrostatic discharge (ESD) can damage Fortinet equipment. Only perform the procedures described
in this document from an ESD workstation. If no such station is available, you can provide some ESD
protection by wearing an anti-static wrist strap and attaching it to an available ESD connector or other
bare metal object.
Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according
to your local regulations.
IMPORTANT: Switzerland: Annex 4.10 of SR814.013 applies to batteries.
警告
本電池如果更換不正確會有爆炸的危險
請依製造商說明書處理用過之電池