Front Panel Controls - Harman Kardon AVR525 Service Manual

AVR525
1 3
2 4
1 Main Power Switch
2 System Power Control
3 Power Indicator
4 Headphone Jack
5 Tone Mode
6 Speaker Selector
7 Surround Mode Group Selector
8 Surround Mode Selector
9 Tuning Selector
)
Button
‹
! Tuner Band Selector
@ Set Button
1 Main Power Switch: Press this button to apply
power to the AVR 525. When the switch is pressed
in, the unit is placed in a Standby mode, as indicated
by the amber Power Indicator 3 surrounding the
System Power Control 2. This button MUST be
pressed in to operate the unit. To turn the unit off and
prevent the use of the remote control, this switch
should be pressed until it pops out from the front
panel so that the word "OFF" may be read at the top
of the switch.
NOTE: This switch is normally left in the "ON" position.
2 System Power Control: When the Main Power
Switch 1 is "ON, " press this button to turn on the
AVR 525; press it again to turn the unit off. Note that
the Power Indicator 3 surrounding the switch will
turn green when the unit is on.
˘
¯
5 7 9
6 8
#
Button
›
$ Preset Station Selector
% Input Source Selector
^ Tuner Mode Selector
& Optical 3 Digital Input
* Input/Output Status Indicator
( Coaxial 3 Digital Input/Output
Ó Video 4 Input/Output Jacks
Ô Bass Control
 Balance Control
Ò Treble Control
Ú Channel Adjust Selector
3 Power Indicator: This LED will be lit in amber
when the unit is in the Standby mode to signal that the
unit is ready to be turned on. When the unit is in oper-
ation, the indicator will turn green.
4 Headphone Jack: This jack may be used to listen
to the AVR 525's output through a pair of headphones.
Be certain that the headphones have a standard
stereo phone plug. The main room speakers will
automatically be turned off when the headphone jack
is in use.
5 Tone Mode: This button controls the tone control
settings, enabling adjustment of the bass and treble
boost/cut or the removal of the tone controls from the
signal path. The first press of the button displays a
TONE IN message in the Main Information
Display ˜. If you wish to set the tone controls to "flat, "
without any treble or bass alteration, press the
FRONT-PANEL CONTROLS FRONT-PANEL CONTROLS
˜
! # %
) @ $ ^
1
/ "
4
‹ ›
or
5
5
harman/kardon
ı Ò
25
ˆ Ú
26
& ( Ô
*
Ó 
Û Delay Adjust Selector
Ù Digital Input Selector
ı Volume Control
ˆ Input Indicators
˜ Main Information Display
¯ Remote Sensor Window
˘ Surround Mode Indicators
Selector Buttons )# so that TONE OUT
appears in the Lower Display Line B.
6 Speaker Selector: Press this button to begin the
process of configuring the AVR 525 for the type of
speakers it is being used with. For complete informa-
tion on configuring the speaker settings using the
front-panel controls see page 23.
7 Surround Mode Group Selector: Press this but-
ton to select the top-level group of surround modes.
Each press of the button will select a major mode
grouping in the following order:
Dolby Modes _ DTS Digital Modes _ VMAx Modes
Dolby Modes DTS Digital Modes
_ DSP Modes _ Stereo Modes _ Logic 7 Modes
DSP Modes Stereo Modes
B
Once the button is pressed so that the name of the
desired surround mode group appears in the on-screen
display and in the Lower Display Line B, press the
VMAx Modes
Logic 7 Modes