Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
3. Keep wires away from high voltage, high temperature components and sharp edges. 4. Keep wires in their original position so as to reduce interference. 5. Usage of this product please refer to also user’s manual. - 4 – ViewSonic Corporation...
Page 5
Do and that may cause “Mura.” not touch the surface of the polarizer. Taking out the monitor by grasping the LCD Take out the monitor with cushions panel. That may cause “Mura.” - 5 – ViewSonic Corporation...
Page 6
“Mura.” Place the monitor on the lap, the panel The panel is placed facedown on the lap. That surface must be upwards. may cause “Mura.” - 6 – ViewSonic Corporation...
Operating: 0°C to +40°C Temperature Storage: -20°C to +60°C Analog / Digital Input Signal Energy Star compliant VESA DPMS compatible Power Management ≦1 W Input Voltage : 90V~264ACV,50~60Hz(auto switch) Power Consumption: 39 Watts(Max.) 36 Watts(Typ.) - 7 – ViewSonic Corporation...
Page 8
1024 x 768 @ 85Hz, 68.67kHz 1152 x 870 @ 75Hz, 68.6kHz 1280 x 1024 @ 60Hz, 63.4kHz 1280 x 1024 @ 75Hz, 79.97kHz 1280 x 720 @ 60Hz, 45kHz Primary Preset::VESA : 1280 x1024@60Hz - 8 – ViewSonic Corporation...
Page 9
Red video input Green video input Blue video input No Connection Ground Red video ground Green video ground Blue video ground H/V sync ground No connection (SDA) Horizontal sync (Composite sync) Vertical sync (SCL) SIGNAL LEVEL - 9 – ViewSonic Corporation...
Front Panel Function Controls And Indicators - 11 – ViewSonic Corporation...
Page 12
• If necessary, make small adjustments using H. POSITION and V. POSITION until the screen image is completely visible. (The black border around the edge of the screen should barely touch the illuminated “active area” of the LCD display.) - 12 – ViewSonic Corporation...
Page 13
1. To select color (R, G or B) press button [2]. 2. To adjust selected color, press ▼ ▲ Important: If you select RECALL from the Main Menu when the product is set to a Preset Timing Mode, colors return to the 6500K factory preset. - 13 – ViewSonic Corporation...
Page 14
Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and ® the ViewSonic website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
Page 15
OSD Background allows the user to turn the OSD background On or Off. Memory Recall returns the adjustments back to factory settings if the display is operating in a factory Preset Timing Mode listed in the Specifications of this manual. - 15 – ViewSonic Corporation...
Page 16
[1] + [▲] display for 5 seconds. • OSD Unlock: Press and hold “[1], & ▲” again for 10 seconds. Volume mute on/off Remark : All the short cuts function are only available while OSD off - 16 – ViewSonic Corporation...
Monitor Block Diagram Flat Panel and CCFL Drive. CCFL backlight RS232 Connector Power Board Main Board For white balance (Include: adapter, inverter) adjustment in factory mode Video signal, DDC Key Board AC-IN HOST Computer 100V-240V - 17 – ViewSonic Corporation...
Page 18
4.2 POWER BLOCK FUNCTION DESCRIPTION Inverter Block Function - 18 – ViewSonic Corporation...
Page 19
Power Block Function - 19 – ViewSonic Corporation...
Page 20
AVSO ADC vertical sync input 5V tolerance Power from PIN 13 AHSO ADC horizontal sync input Adjustable Schmidt trigger 5V tolerance Power from PIN 13 AIC1084-33PM (U701): DC power convert, used to 5v convert 3.3v. - 20 – ViewSonic Corporation...
Page 21
It includes an 8051 CPU core, 768-byte SRAM, 4 channels of 6-bit ADC, 3 external counters/timers, 6 channels of PWM DAC, VESA DDC interface, and a 64K-byte internal program Flash-ROM memory. Circuit Diagram - 21 – ViewSonic Corporation...
Page 22
General purpose I/O/Slave llC1 SCL2(open drain) P5.7/HSDA2 General purpose Output/Slave llC1 SCL2(open drain) High Active RESET HSCL1/P3.0/RXD Slave IIC clock/General purpose I/O/Rxd (open drain) HSDA1/P3.1/RXD Slave IIC clock/General purpose I/O/Txd (open drain) P3.2/INT0 General purpose I/O/External interrupt 0(Standard 8051) - 22 – ViewSonic Corporation...
Page 23
TDA7496L (U201): The UTC TDA7496L is a stereo 2W+2W class AB power amplifier, specially designed for high quality sound, TV and Monitor applications. Features of the UTC TDA7496L include linear volume control, Stand-by and mute functions. Pin Function - 23 – ViewSonic Corporation...
Page 24
Supply voltage pin This pin is to program the switching frequency. By connecting a resistor to ground to set the switching frequency. Unconnected pin Supply voltage pin Gate drive output to drive the external MOSFET - 24 – ViewSonic Corporation...
Page 25
Feedback Input Dimming Voltage Input COMP Error Amplifier Output Vref Reference Voltage Soft Start Dimming Mode Selection Main Ct Burst Dimming Frequency Supply Voltage Open Lamp Protection Vcc1 Output Drive Source Voltage Shutdown Protection Output Drive - 25 – ViewSonic Corporation...
D、MEM.CHANNEL 12 ( 5000 color): 5000 color temp. parameter is Wx = 0.346±0.02;Wy = 0.359 ±0.02; Y > 210 cd/m E、MEM.CHANNEL13 ( SRGB color): SRGB color temp. parameter is Wx = 0.313±0.02;Wy = 0.329 ±0.02; Y > 220 cd/m - 27 – ViewSonic Corporation...
Page 28
3.)Into factory mode of VA712b-2 A、First Power off, then press Switch 2 button along with press Power button will activate the factory mode, then MCU will do AUTO LEVEL automatically. Meanwhile press MENU the OSD screen will located at LEFT TOP OF PANEL.
Page 29
(5)、Adjust the GREEN of color3 on factory window until Chroma 7120 indicator reached the value G=100 (6)、Adjust the BLUE of color3 on factory window until Chroma 7120 indicator reached the value B=100 (7)、Repeat above procedure ( item 4,5,6) until Chroma 7120 RGB value meet the tolerance =100±5 - 29 – ViewSonic Corporation...
Page 30
30 minutes with the following conditions: (a)In room temperature, (b) With full-white screen, RGB, and Black (c) With cycled display modes, 640*480 (H=43.27kHz, V=85Hz) 800*600 (H=53.7kHz, V=85Hz) 1024*768 (H=68.67kHz, V=85Hz) 1280*1024 (H=79.97kHz, V=75Hz) - 30 – ViewSonic Corporation...
Page 31
White Screen & Dark pixels should Figure 7,8 Pixel/Line Screen compliant with the spec. The screen must have White Balance White & Black Pattern the pure white and black Figure 9 pattern, no other color. - 31 – ViewSonic Corporation...
Page 32
Fine Line Morie Pattern (Figure1) Gray Scale Pattern (Figure2) Horizontal & Vertical Thickness Pattern R. Color Pattern (Figure 4) (Figure 3) G. Color Pattern (Figure 5) B. Color Pattern (Figure 6) - 32 – ViewSonic Corporation...
Page 33
ASIC. For optimum screen quality, the user has to adjust each function manually. Firmware Test Pattern: Burn In Mode (Refer to Chapter III-3. Hot Keys for Function Controls) Make sure the F/W is the latest version. Test Pattern: EDID program - 33 – ViewSonic Corporation...
Page 34
- Check if the Mura can pass 10% ND Filter. Audio Test Signal: Voice signal (optional, depend on model) Test Pattern: liberty - Make sure there is audio output. - Make sure that audio function (volume 80%) is working without noise and - 34 – ViewSonic Corporation...
Page 35
After final QC step, we have to erase all saved changes again and restore the factory defaults. You should do “All Mode Reset” again. Power Off Monitor Turn off the monitor by pressing “Power” button. - 35 – ViewSonic Corporation...
Page 36
2 Setup Procedure 2.1 Connect P1 of Fixture with printer port of PC by LPT Cable. 2.2 Connect P2 of Fixture with VA712-2/VA712b-2 Monitor by VGA Cable. 2.3 Connect Power Cord to VA712-2/VA712b-2 Monitor. 2.4 Connect P3 to the Signal Generator (eg.Chroma2326) for verifying it after the operation being completed.
Page 37
3 Firmware Upgrade Procedure Step 1. Let VA712-2/VA712b-2 set to be connected with AC cable and VGA cable. Step 2.Execute the MSstar ISP tool. - 37 – ViewSonic Corporation...
Page 38
Step 3. Click “Create Security File” button. Open a new window to key in security code. Step 4.Set “Command NO” to 4,and key in security code :“94,94,ac,ca,53” to shown as following, then press “OK” button to close window. - 38 – ViewSonic Corporation...
Page 39
Step 5. Click dropdown listbox for MTV type, select the “MTV512M64” viewed on your set. Step 6. Click “Load MCU File” button. Select the object bincode on your corresponding directory. Step 7. Click “确定” button to finish the selection of bincode. - 39 – ViewSonic Corporation...
Page 40
Step 8. Select “Auto” optionbutton, then execute the flashing action by clicking the “RUN” button. Step 9. If the flashing F/W has been completed, the message of “Check MCU CRC OK” on the right TextBox means the Host verify ok for the progress of program. - 40 – ViewSonic Corporation...
Page 41
Step 10. Unplug and replug power cord of VA712-2/VA712b-2 set and then check the OSD operation and image on srceen. Step 11. At last, do “Memory Recall.” 3.2 Setup Procedure 3.2.1 Connect P2 and monitor of Fixture with VGA ports of VA712-2/VA712b-2 by VGA Cable.
Page 42
3.3 DDC Key In Procedure Sep1.Select and execute DDC Key In program - 42 – ViewSonic Corporation...
Page 43
Sep2:Inpute the S/N and execute “Enter” - 43 – ViewSonic Corporation...
Page 49
89G 728GAA902 SIGNAL CABLE 89G 728HAA902 SIGNAL CABLE 89G1748GAADVI SIGNAL CABLE 89G1748HAADVI SIGNAL CABLE 89G1748LAADVI SIGNAL CABLE 89G402A18N IS POWER CABLE 89G402A18N LS POWER CORD 95G8014 14 34 HARNESS 14P-14P 50mm 95G8014 16926 WIRE HARNESS - 49 – ViewSonic Corporation...
12、 Disassemble the 2 fixed screws of the panel, remove the main frame, as showed in the following the picture 18,19,20. Do not damage the cable of the panel. 13、 That’s all. The disassemble process of the unit is over. - 70 – ViewSonic Corporation...
Page 91
Add: Tel: Fax : E-Mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestion to the Director, Quality System & Process (marc.maupin@viewsonic.com) - 91 – ViewSonic Corporation...