Table of Contents
Advertisement
SUB
BAND
PWR
MD
DISP
PTY
1
10
9
SUB
BAND
PWR
MD
Operating and Installation Guide
DISP
PTY
8
7
MT2108
COMPACT
DIGITAL AUDIO
TA
AF
1 PAU
2 INT
2
3
COMPACT
DIGITAL AUDIO
TA
AF
1 PAU
2 INT
6
5
18
19
3 RPT
4 RDM
14
3 RPT
4 RDM
20
21
4
(1-6)
REL
SCN
A/PS
5
6
11
REL
SCN
A/PS
5
6
22
23
13
12
TUNE/
TRACK
15
TUNE/
TRACK
Advertisement
Table of Contents
Related Manuals for Mutant MT2108
Summary of Contents for Mutant MT2108
- Page 1 MT2108 BAND TUNE/ COMPACT TRACK DIGITAL AUDIO A/PS DISP 1 PAU 2 INT 3 RPT 4 RDM BAND Operating and Installation Guide TUNE/ COMPACT TRACK DIGITAL AUDIO A/PS DISP 1 PAU 2 INT 3 RPT 4 RDM (1-6)
-
Page 2: Locations Of Controls
A/PS DISP 1 PAU 2 INT 3 RPT 4 RDM LOCATIONS OF CONTROLS BAND TUNE/ COMPACT TRACK DIGITAL AUDIO A/PS DISP 1 PAU 2 INT 3 RPT 4 RDM BAND COMPACT DIGITAL AUDIO BAND (1-6) DISP 1 PAU TUNE/ COMPACT TRACK DIGITAL AUDIO . POWER ON/OFF (PWR) -
Page 3: Installation Precautions
INSTALLATION PRECAUTIONS • Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. • Use only the supplied mounting hardware for a safe and secure installation. • Be sure to remove the front panel before installing the unit. Mounting angle adjustment Adjust the mounting angle to less than 20°. MOUNTING EXAMPLE Installation in the dashboard Release screw and bracket 182mm 53mm Bend these claws, if necessary Note: Keep the release key in a safe place as you may need it in the future to remove the unit from the car. Detaching and attaching the front panel The front panel of this unit can be detached in order to prevent the unit from being stolen. -
Page 4: To Support The Unit
1. UNIT TO SUPPORT THE UNIT 2. RELEASE CASE 3. DASH BOARD 4. HEX NUT 5. LOCK WASHER Dashboard 6. PLAIN WASHER 7. CAR BODY 8. REAR SUPPORT STRAP 9. TAPPING SCREW 10. M5 X 15 HEX BOLT ISO CONNECTOR RCA Jack Line Out (Front): Red (right) White (left) RCA Jack Line Out (Rear): Red (right) White (left) RCA Jack Line In: Red (right) White (left) -
Page 5: Power On/Off
OPERATING INSTRUCTIONS 1. POWER ON/OFF By pressing this key, the unit is switched on or off. This unit is turned on by pressing any key. 2. SELECT 3. VOLUME UP/DOWN Turning the VOL knob Right or Left (3), you can adjust VOL/BASS/TREB/BAL/FAD. To select other functions, press the VOL knob shortly until the desired functions is shown on the display. Figure shows how control functions are selected using the VOL knob. Fig. Selection of sound control functions . VOL 2. SEL 3. BAS 4. TRE 5. BAL 6. FAD Turning the VOL knob Right or Left. Increase or decrease the volume by turning . These buttons can be used to adjust the BASS, TREBLE, BALANCE and FADER. TA SEEK/TA ALARM (2) When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function. TA SEEK Mode or TA ALARM mode is selected by 2 sec. TA SEEK TA SEEK / TA ALARM - TA SEEK mode:... -
Page 6: Seek Mode
2 sec. TA SEEK MASK DPI MASK DPI / MASK ALL 2 sec. 2 sec. TA SEEK TA SEEK / TA ALARM AUDIO DSP CONTROLS (2) TA SEEK MASK DPI RETUNE RETUNE L / RETUNE S When press the VOL knob for more than 2 seconds, it is activated as selecting mode of 2 sec. these function. TA SEEK MASK DPI MASK DPI / MASK ALL... - Page 7 2 sec. TA SEEK MASK DPI RETUNE LOUD ON/OFF 2 sec. 2 sec. TA SEEK MASK DPI RETUNE LOUD TA SEEK MASK DPI RETUNE LOUD 2 sec. TA SEEK MASK DPI RETUNE LOUD STEREO/MONO (2) BEEP ON/OFF BEEP SEEK SEEK1 / SEEK 2 When press the VOL knob for more than 2 seconds, it is activated as selecting mode of these function.
-
Page 8: Display (Disp)
5. ‘AF/REG’ function (ALTERNATIVE FREQUENCIES) When pressed momentarily, AF/REG switching mode is selected. When AF/REG switching mode is selected, the radio checks the signal strength of the AF all the time. When pressed long, it is activated as regional mode ON/OFF. – Regional mode ON: AF switching or PI SEEK is implemented to the station which have all PI codes same as current station. REG segment is turned on, in LCD display. – Regional mode OFF The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented. 6. ‘TA’ function (TRAFFIC ANNOUNCEMENT) When pressed momentarily, it is activated as TA mode on or off When TA mode is on and traffic announcement is transmitted – When the unit is in CD/MP3 mode, it will switch to radio mode temporarily. – If the volume level was under the threshold point, it will be raised to the threshold point. – When TP station is received, TP segment is turned on in LCD display. 7. ‘PTY’ function (PROGRAM TYPE) PTY MUSIC ---- PTY SPEECH ---- PTY OFF While selecting PTY type, its selection is implemented by preset buttons as described in preset key. When PTY is selected, the radio starts to search corresponding PTY information, and stops if the corresponding PTY information is detected. 8. DISPLAY (DISP) When this key is pressed, it is operated as the conversion of each display mode as follow. 1) In case of receiving RDS station. RADIO MODE PS ---- CT ---- FREQ ---- PTY CD/MP3 PLAYER MODE CDP ---- CT ---- PS ---- FREQ ---- PTY... - Page 9 12. AUTO SEEK SEARCH TUNING (A/PS) By pressing shortly, the radio searches for each preset station. When field strength level is bigger than the threshold level of stop level, the radio is holding at that preset number for 5 sec. with releasing mute, and then searches again. By pressing longer than sec, and then 6 strongest stations are preset to the corresponding preset number. When AS operation is finished, the radio executes the preset scan. 13. ‘SCAN’ AUTOMATIC TUNING CONTROL (SCN) This key is operated as RADIO SCAN. The operation is similar as normal search but differ- ent thing is holding 5 seconds on every station detected in RADIO SCAN mode. 14. LCD DISPLAY The Liquid Crystal Display will display the current state of the unit. 15. OPEN THE FRONT PANEL Press button and the front panel will open. CD/MP3/WMA CONTROL LOCATION OF PARTS 16. CD SLOT Carefully insert the CD into the disc slot with the label side uppermost. The CD starts auto- matically play.
-
Page 10: How To Select Mp3/Wma Files
HOW TO SELECT MP3/WMA FILES 1. Searching Track: • Press “A/PS”, then searching track is activated. • Press “VOL” knob, then the first digit is blinking. • Turn VOL to right or left, select first digit you want. • Press “VOL” knob, then the first digit is fixed and second digit is blinking. • Turn VOL to right or left, select 2’nd 3’rd respectively. • Then automatically the song you selected will start. 2. Searching File Name: • Press “A/PS” twice, then file search is activated. • Press “VOL” knob, then the first directory is displayed. • Turn VOL to right or left, you can select the directory you want. • Press “VOL” knob again, then the directory is fixed and the first file name is displayed. • Turn VOL to right or left, you can select the file you want. • Press “VOL” knob, then the song you selected will start. 3. Searching Character: • Press “A/PS” 3 times, then character search mode is activated. • Press “VOL” knob, then “A” character is displayed. -
Page 11: Technical Specifications
TECHNICAL SPECIFICATIONS CD/MP3/WMA PLAYER SECTION Signal to Noise Ratio > 60 dB Channel Separation > 50 dB (kHz) Frequency Response 20Hz - 20 kHz TUNER (FM) Frequency range 87.5-08 MHz Intermediate frequency 0.7 MHz Sensitivity 2.8 µV Stereo separation 30 dB Signal to noise ratio 50 dB Channel step 50 kHz TUNER (MW) Frequency range 522-620 KHz Intermediate frequency 0.7 MHz Usable sensitivity 32 dBµV LINE-OUT Output Impedance 0k Ohm GENERAL Power Supply 2V DC (0.8-5.6V allowable) Speaker impedance 4 or 8 ohm Output power...
Need help?
Do you have a question about the MT2108 and is the answer not in the manual?
Questions and answers