Sony SLV-SE220 Service Manual page 2

QQ
3 7 63 1515 0
/,1( '(&(;7 /,1( '(&(;7
SLQ
9LGHR LQSXW SLQ 
$XGLR LQSXW SLQV  DQG 
t /,1( / o 5

9,'(2 ,1 SKRQR MDFN 
,QSXW VLJQDO  9SS  RKPV
XQEDODQFHG V\QF QHJDWLYH
$8',2 ,1 SKRQR MDFN 
,QSXW OHYHO  P9UPV
,QSXW LPSHGDQFH PRUH WKDQ  NLORKPV
$8',2 2876257,( 5' /*
3KRQR MDFN 
5DWHG RXWSXW OHYHO  P9UPV
/RDG LPSHGDQFH  NLORKPV
2XWSXW LPSHGDQFH OHVV WKDQ  NLORKPV
QRW DYDLODEOH RQ 6/96(1

6/96(1 RQO\

QRW DYDLODEOH RQ 6/96(1 DQG

6(.
*HQHUDO
3RZHU UHTXLUHPHQWV
 ±  9 $&  +]
3RZHU FRQVXPSWLRQ
 : 6/96(.
 : 6/96(1 6(1 6;1
DQG 6(1
TE
L 13942296513
 : 32:(5 6$9( LV VHW WR 21
PLQLPXP
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are "pinched"
or contact high-wattage resistors.
www
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to
the customer and recommend their replacement.
.
http://www.xiaoyu163.com
2SHUDWLQJ WHPSHUDWXUH

°& WR °&
6WRUDJH WHPSHUDWXUH
±°& WR °&
'LPHQVLRQV LQFOXGLQJ SURMHFWLQJ SDUWV DQG
FRQWUROV ZKG
$SSUR[  î  î  PP
6/96(.
$SSUR[  î  î  PP
6/96(1 6;1 DQG 6(1
$SSUR[  î  î  PP
6/96(1

0DVV
$SSUR[  NJ 6/96(.
$SSUR[  NJ 6/96(1 6(1
6;1 DQG 6(1
6XSSOLHG DFFHVVRULHV
5HPRWH FRPPDQGHU 
5 VL]H $$ EDWWHULHV 
$HULDO FDEOH 
'HVLJQ DQG VSHFLILFDWLRQV DUH VXEMHFW WR
FKDQJH ZLWKRXW QRWLFH
SAFETY CHECK-OUT
x ao u163
y
i
— 2 —
http://www.xiaoyu163.com
2 9
8
Q Q
3 6 7 1 3 1 5
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C during
co
repairing.
• Do not touch the soldering iron on the same conductor of the
.
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
9 4 2 8
0 5 8 2 9 9 4 2 8
m
9 9
9 9