Advertisement
Special Fitting Instructions
For use when fitting rear cycle carriers
to the Renault Laguna 5dr. Hatch
Due to the rubber moulding running around
To eliminate this we advise mounting the
the edge of the rear window, mounting of the
carrier top straps as detailed in this
top straps along the top edge of the rear
special instruction.
window can cause deformation and eventually
damage to the moulding.
15
16
Feed the top straps through the tailgate
Note: The manufacturer operates a policy of continuous
development, and reserves the right to alter specifications
hinges as shown (one strap each side),
.
without notice
leaving the glass anchor tube hanging freely
In the event of fitting difficulties, telephone our
inside (Fig 15). Carefully close hatch and then
helpline on 01525 850800.
pull free ends of straps trapping anchor tubes
against the interior trim. (Fig 16).
Attach both straps to cycle carrier and refer to
the cycle carrier instructions for all
remaining fitting instructions.
Fitment guide
NON-RECOMMENDED FITS
It is recommended that conventional rear mount carriers are not fitted to the following vehicles.
Sports cars
Due to insufficient strength of lightweight or composite panels,
and unsuitable body curvature.
Cabriolets
Due to fixing points being impeded by hood mechanisms,
and reduced space on rear of vehicle.
Split tailgate
Due to insufficient strength of hinges, and difficulty to fit carriers correctly.
Side opening
Due to insufficient strength of hinges, and difficulty to fit carriers correctly.
tailgate
In most cases an alternative carrying solution can be recommended, such as a roof or tow ball
mounted carriers. The table below lists some examples of non-recommended fits with some
alternative solutions for carrying cycles (correct at time of printing).
NON-RECOMMENDED FITS
VEHICLE
YEAR
SOLUTION
Audi A2
00-
Roof mount or tow ball mount
Audi A4
01-
Roof mount or tow ball mount
Audi TT
99-
Roof mount
BMW 3 Series (E36)
91-98
Roof mount or tow ball mount
Citroen AX
92-
Roof mount or tow ball mount
Fiat Coupe
95-
Roof mount or tow ball mount
Ford Probe
94-
Roof mount or tow ball mount
Ford Puma
97-
Roof mount or tow ball mount
Jaguar XK8/XKR
96-
Roof mount
Mazda MX-3
91-
Roof mount
Mazda MX-6
92-
Roof mount
Mercedes C-class (W202)
93-01
Roof mount or tow ball mount
Austin/Rover Mini
62-00
Roof mount
Land Rover Discovery
89-
Roof mount or tow ball mount
Land Rover Freelander
98-
Roof mount or tow ball mount
Range Rover
70-
Roof mount or tow ball mount
Rover 400
95-
Roof mount or tow ball mount
Vauxhall Tigra
94-
Roof mount or tow ball mount
VW Beetle T1 (Old)
52-
Roof mount
VW Beetle (New)
99-
Roof mount or tow ball mount
Volvo 480
92-
Roof mount or tow ball mount
Special Recommendations
Avoid any vehicle bodywork of insufficient
The carrier may obstruct the rear window
strength, trim and items such as aerofoils or
wiper of your vehicle. DO NOT operate the
spoilers.
wiper with the carrier fitted.
IMPORTANT! Carrier straps must always be
When positioning cycles on the carrier
re-tightened after cycles have been mounted to
ensure that they do not project beyond the
the carrier. Straps should be checked routinely
profile of the vehicle and that no part of any
for signs of wear and abrasion, and any worn
cycle can touch the paintwork.
straps must be replaced immediately.
The use of rear mounted cycle carriers may
After driving for a few miles STOP and check
be restricted in certain countries outside the
that all straps are secure and tight. If
UK. Always check with the relevant national
necessary, tighten the straps and tidy away any
tourist authorities prior to commencing
loose ends. This must be repeated at suitable
your journey.
intervals depending on the nature of the road.
Use cloth or foam padding to prevent
Do not exceed 45kg maximum load (3 adult
abrasion damage occurring between the frames
cycles) or 30kg maximum load (2 adult cycles)
of your cycles, or from contact between the
when the carrier is used on a booted saloon.
cycles and the cycle carrier. Halfords foam pad
cycle protectors are available.
To ensure full compliance with the road
Care must be taken when positioning and
traffic regulations, the use of lighting board/
number plate is required if your vehicle's
loading the cycle carrier to avoid placing cycle
existing lighting/number plates are obscured
tyres near the exhaust, and to ensure that a
by the use of the carrier.
satisfactory ground clearance is maintained
between the cycles and the road. Extra care
Drive with care, the handling characteristics
should be taken when negotiating rough road
of your vehicle will be affected when carrying
surfaces, humps and ferry ramps.
cycles, (e.g. cornering, braking, side winds etc).
All lengths are approximate.
Retain these instructions for future
reference, ensure that any other users of the
cycle carrier are familiar with their contents.
Halfords Ltd. Washford Redditch B98 ODE
Made in the UK
High 3 Bike Carrier
Fitting Instructions
Please follow instructions carefully to ensure the safety of yourself and other road users.
The initial assembly and fitting of this carrier will take approximately 15 minutes.
Before you begin:
Due to the construction of boot lids we recommend only two cycles be carried on
saloon cars with this carrier.
Make sure all parts are included in the package.
Ensure that the vehicle boot lid/rear bumper are free from dirt and grime.
Kit Contents
x2
x2
Dumbells
Panel hook
Chassis hook
x2
160cm
Main frame
x4
95cm
See rear of these instructions for non suitable vehicle fitments
x2
Advertisement
