Related Manuals for Memorex RF6000
Summary of Contents for Memorex RF6000
- Page 1 ’ ’ UIDE UIDE RF6000 RF6000 Wireless Wireless Keyboard & Optical Mouse Keyboard & Optical Mouse...
- Page 2 MPORTANT OTICE The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty of representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular purpose of this document.
-
Page 3: Table Of Contents
ABLE OF ONTENTS 1. Introduction 2. System Requirements 3. Installing the Keyboard and Mouse Set 3.1 Getting the Receiver Ready 3.2 Getting the Keyboard Ready 3.3 Getting the Mouse Ready 4. Wireless ID Setting 4.1 Synchronizing the IDs of your Receiver, Keyboard and Mouse 4.2 Replacing Batteries and Resetting ID Buttons 5. -
Page 4: Introduction
Internet from the comfort of your living room couch! The RF6000 Keyboard and Mouse combo consists of a keyboard, an optical mouse and a receiver. The receiver is connected to your PC through a cable, with a connector for both the keyboard and the mouse. -
Page 5: System Requirements
2. System Requirements • IBM PC or Compatible • Available PS/2 Keyboard Port and Mouse Port • CD-ROM or DVD drive (for driver installation) • Microsoft Windows 98 SE, Windows Me, Windows NT 4.0 SP6, Windows 2000 or Windows XP operating systems •... -
Page 6: Installing The Keyboard And Mouse Set
3. Installing the Keyboard and Mouse Set This wireless keyboard and mouse combo consists of a receiver that plugs into the computer, a wireless keyboard, a wireless mouse, and a Mouseport™ charging station. 3.1 Getting the Receiver Ready Connect the receiver and select a wireless channel: 1. -
Page 7: Getting The Keyboard Ready
3.2 Getting the Keyboard Ready Install the two AA alkaline batteries (provided) into the keyboard and select a wireless channel: 1. Turn the keyboard over and find the battery compartment. Lift the cover. 2. Insert the include AA alkaline batteries into the compartment. Make sure the batteries are placed in the correct direction by following the polarity signs in the battery compartment. - Page 8 2. Use the slide switch, located inside the battery compartment of the mouse, to select the same channel as the one selected on the receiver and on the keyboard. Channel Slide Switch 3. Insert the included AAA rechargeable batteries into the compartment. Follow the polarity signs in the battery compartment and make sure the batteries are placed in the correct direction 4.
-
Page 9: Wireless Id Setting
4. Wireless ID Setting The mouse, keyboard and receiver each contain two channels, and each channel contains 256 IDs that are randomly selected when you press the ID button. This ID-recognition function helps protect against interference from other wireless devices in the same environment. After installing the hardware, inserting the batteries and charging the mouse batteries, you must set the IDs of the receiver, mouse and keyboard. -
Page 10: Replacing Batteries And Resetting Id Buttons
5. Turn the mouse over and locate the ID button near the top. Press the ID button with a blunt pointed object, like the tip of a ballpoint pen, and hold until the receiver light is solid. This may take up to 20 seconds. ID button of Mouse Important: If 30 seconds pass before you complete step 5, you must repeat... -
Page 11: Software Installation
After finishing the hardware installation as described in this manual and starting up your PC, you should be able to immediately take advantage of the wireless benefits of the RF6000 keyboard and mouse. If the keyboard and mouse are not working properly, see section 7 "Troubleshooting" for tips on how to solve your problem. -
Page 12: Mouse Driver Installation
2. Browse to the drive where the Installation CD is located. 3. Select the Autorun.exe file, then click on the Open button. 4. Click on OK to start the installation manually. 5. Select installation options for the RF6000 devices and follow the onscreen instructions. -
Page 13: Using The Keyboard And Mouse
6. Using the Keyboard and Mouse 6.1 Using the Keyboard Besides the usual keyboard keys, the RF6000 keyboard also has extra ded- icated keys which provide the following multimedia functionality: Important: In order to use these keys under Windows 98 SE or Windows NT 4.0 SP6, it is necessary to have the keyboard driver installed and is recommended for Windows Me, 2000 and XP as well. -
Page 14: Using The Mouse Driver
Attaching the Wrist Rest At your discretion, you may choose to connect the wrist rest with the keyboard. To connect the wrist rest to the keyboard, follow the images below: 6.2 Using the Mouse After installing the mouse driver as described in section 5, you will be able to start using the Mouse Control Panel by right clicking on the Mouse icon in the Windows task bar. - Page 15 2. Make sure the mouse plug is inserted in the mouse connector on your PC and the keyboard plug is inserted into the keyboard connector on your PC. Compare the icons on both the cable and backside of your PC if necessary. 3.
- Page 16 Technical Support For more information on how to use the RF6000 Keyboard and Mouse, please visit the Memorex website at www.memorex.com/products and fol- low the links to the Keyboard product listings for additional product infor- mation and guides. If you need any additional help in connecting, synchronizing or installing the RF6000, please feel free to contact Memorex's technical support.
- Page 17 FCC Guidelines: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 18 ©2003 Memorex Products, Inc. • Santa Fe Springs, CA 90670 • www.memorex.com All other brand or product names are trademarks or registered trademarks of their respective owners. 5395 6170...