Download Print this page

µ-Dimension Element Owner's Manual page 2

Advertisement

EL CO
AX 4
B / EL COMP 4B / EL CO
Models:
Introduction
Congratulations on your purchase of µDimension
ELEMENT
series
Automotive Loudspeakers! They have
been built to meet
the same
rigorous standards of
construction and performance
that have long
established
our renowned home
and professional speaker systems.
This manual has been designed to make ELEMENT
Automotive
Loudspeaker installation and ownership as
trouble
-free as possible.
Please read through this manual
completely
before attempting any
installation steps and
familiarize
yourself
with your new speaker system.
You will need your purchase receipt as proof of purchase
for
any and
all warranty repairs and for insurance
purposes.
Keep your receipt,
owner's manual, and
packing materials in a safe
location for possible
future
use.
Pre-Installation Instructions
It is recommended that you have your new ELEMENT
series
Autom
otive
Loudspeakers professionally install
by your
authorized ELEMENT dealer. This will
ensure the
use
of proper installation
techniques and
materials, and
will
save much time and effort.
If you
choose to perform
you
own installation, the following instructions will give
you ELEMENT
series direction toward making your
purchase
complete. Read the following information and
precautions carefully. Failure to follow the stated
precautions may result in personal injury and/or
damage the audio system
or vehicle.
A. Always make sure the speaker will easily t into the
intended mounting location and that there is adequate
cavity
depth to
accept
the magnet structure.
B. Check for adequate clearance between speaker and
window, window crank, power window mechanism,
seat, glove box, rear deck torsion bars, and other items
which may interfere with the speaker's mounting. This is
especially important if any hole cutting is required.
complete speaker, mounting size and depth requirements
can be found at the end of this manual. A good way to
conrm speaker place meet on a door or body panel is
to place the speaker's die cast mounting ring onto the
surface. Check for a at mounting surface, free from all
obstruction.
MP 6
B / EL COMP 6V
C. The method of installation chosen and level of
execution will effect the overall performance of the
speaker system. Treat each installation step with a high
degree of attention.
D. Do not mount the speaker where water may splash
the woofer cone. A plastic cup or some heavy gauge
plastic sheeting may be needed in some locations that
are exposed to moisture from behind the body panel.
E. Care must be taken to prevent low frequency cancel-
lation caused by air leakage between the front and rear
of the speaker (such as when mounted on a curved or
uneven surface, or when mounted in an oversized hole).
F. Mounting panel reinforcement may be necessary in
some cases in order to prevent surface ex. This can be
achieved by mounting the speaker on a metal or
wooden sub-bafe behind the body or door panel.
Consult an installation specialist for further direction.
G. Unless you are replacing existing speakers of same
size, mounting locations will have to be cut into the
doors, body panels, or rear deck. In some cases speaker
mounting holes will be precut in the doors, body panels,
or rear deck steel. Due to their structural integrity and
accessibility. These precut mounting holes should be
used whenever possible.
ed
IMPORTANT: Never cut any metal that is an integral
part of an automobile's safety or structural support
system.
ELEMENT Speaker Installation
NOTE.
µDimension s
trongly recommends that you operate
the complete audio system at low volume before nal
installation of your ELEMENT Automotive Loudspeakers.
This will allow a trial listening test before securing the
loudspeakers into their mounting locations.
CAUTION: Make sure that all speaker wiring is fully
protected from cutting or wear. Any short circuits
developing as a result could severely damage the
rado unit or amplier. Make sure that all speaker
wires easily reach the speaker terminals with stress
on the wire or connectors.
General Features
EL COAX 4B
High Performance 4" 2 Way BMW Coaxial Speaker
BMW 100mm ABS basket, resonance free solid screw terminal.
Strong neodymium magnet
and
solid screw terminal connection
4" ELEMENT P.P. cone with rubber surround.
BMW OEM plug & play with 20mm
neodymium
EL COMP 4B
High Performance 4" 2 Way BMW Component system
BMW 100mm ABS basket, resonance free solid screw terminal.
Strong neodymium magnet with pole piece VC cooling ventilation.
4" ELEMENT P.P. cone with phase plug dustcap at rubber surround.
25mm silk dome Tweeter with neodymium magnet, ush/surface mounts.
BMW OEM plug & play crossover with tweeter protection, pre wired.
Optional ELEMENT -3dB tweeter level plug & play resistor included.
EL COMP 6B
High Performance 6-3/4" 2 Way BMW Component System
BMW E46 OEM size stamped basket with voice coil cooling vents.
Strong high grade magnet with pole piece voice coil cooling vent.
6-3/4" ELEMENT P.P. cone with phase plug dustcap at rubber surround.
25mm silk dome Tweeter with neodymium magnet, ush/surface mounts.
BMW OEM Plug & Play crossover with tweeter protection, pre wired.
Optional ELEMENT -3dB tweeter level Plug & Play resistor included.
EL COMP 6V
High Performance 6-
1/2
" 2 Way VW Component system
Euro DIN stamped basket, 6-1/2" ELEMENT P.P. cone with phase plug dustcap.
Strong high grade magnet, protected with ELEMENT rubber cover.
VW Golf 6+7 mount 25mm silk dome Tweeter with neodymium magnet.
VW Golf 6+7 OEM Plug & Play crossover with tweeter protection, pre wired.
VW Golf 6+7 OEM resonance free ABS installation adapters included.
Optional ELEMENT -3dB tweeter level Plug & Play resistors included.
Specification:
EL COAX 4B
Woofer V.C. Diameter
25mm
Tweeter V.C. Diameter
20mm
System Impedance
4ohms
Power Handling (RMS)
5 W
0
Power Handling (Max)
100W
Frequency Response
100-20k Hz
Sensitivity
88dB (1W/m)
silk dome Tweete
r.
EL COMP 4B
EL COMP 6B
EL COMP 6V
25mm
25mm
25mm
25mm
25mm
25mm
4ohms
4ohms
4ohms
50W
7 W
0
7 W
0
1 0W
2
150W
150W
100-22k Hz
60-22k Hz
60-22k Hz
88dB (1W/m)
90dB (1W/m)
90dB (1W/m)

Advertisement

loading