Advertisement
Advertisement
Table of Contents
Related Manuals for Floorpul ruby 45e
Summary of Contents for Floorpul ruby 45e
- Page 1 45e ruby 50e ruby 55e 01 2007 Use and maintenance Attention! Please read the instructions before use. COD. 65305002...
-
Page 2: Table Of Contents
SUMMARY LEGEND INSTRUMENT BOARD AND CONTROLS LEGEND MACHINE OPTIONAL ACCESSORIES TECHNICAL DESCRIPTION INTRODUCTORY COMMENT GENERAL RULES OF SECURITY SYMBOLOGY BEFORE USE Handling of the packed machine Unpacking of the machine Squeegee assembly Adjustment of the squeegee height Adjustment of the squeegee inclination Splash guard assembly Manual assembly of the brushes Automatic brush assembly (ruby50e) -
Page 3: Legend Instrument Board And Controls
LEGEND INSTRUMENT BOARD AND CONTROLS SWITCH BRUSHES MOTOR RESTORABLE FUSE BRUSHES MOTOR SWITCH SUCTION MOTOR SWITCH WITH KEY (OPTIONAL) PUSH BUTTON BRUSH RELEASE (only on ruby 50e) LEVERS FOR PRESENCE HOUR METER (OPTIONAL) 10. LEVER SOLUTION VALVE SIGNAL LAMP FOR PRESENCE OF THE TENSION 11. -
Page 4: Optional Accessories
OPTIONAL ACCESSORIES Solenoid valve Adjustment brushes pressure Adjustment brushes inclination (ruby45e, 55e) Emptying device of the solution tank Switch with key Hour meter TECHNICAL DESCRIPTION ruby 45e ruby 50e ruby 55e Cleaning width Squeegee width Working capacity, up to sqm/h 1575... -
Page 5: Introductory Comment
INTRODUCTORY COMMENT Otherwise, ask for technical advice to an author- Symbol denoting the flash. Thank you for having chosen our machine. This ized assistance centre. Indicates the signal lamp for floor cleaning machine is used for the industrial - Where parts are required, ask for ORIGINAL presence of the mains tension and civil cleaning, suitable for hard and not very spare parts to the distributor and/or to an au-... -
Page 6: Before Use
BEFORE USE ADJUSTMENT OF THE SQUEEGEE HEIGHT Hook the spring in the rear part of the brushes The squeegee must be adjusted in height de- base group to the slot placed at the extremity of HANDLING OF THE PACKED MACHINE pending on the rubber wear. -
Page 7: Automatic Brush Assembly (Ruby50E)
AUTOMATIC BRUSH ASSEMBLY (ruby50e) Put the brush onto the floor next to the brush ATTENTION: base. Use always low foam detergent. To avoid foam 1. Check that there is the electric supply. presence, before starting working operation, in- 2. Lift the brush base acting upon the pedal. troduce into the recovery tank a minimum quan- 3. -
Page 8: Emptying Detergent Solution
When this happens, it is necessary to take off the 5. Turn the brushes motor switch off (1). plug from the mains socket and to empty the re- 6. Turn the suction motor switch off (2). covery tank. 7. Take off the plug from the mains socket. 1. -
Page 9: Brushes Disassembly (Ruby45E, Ruby55E)
1. Take off the squeegee hose (3) from the cou- BRUSHES DISASSEMBLY (ruby45e, ruby55e) pling. 2. Disassemble the squeegee from the support rotating the lever (2) counterclockwise sliding ATTENTION: the stud bolts (1) in their slots. Check that the plug is disconnected. 3. -
Page 10: Six-Monthly Maintenance
THE BRUSHES MOTOR DOES NOT WORK 3. Check that the suction hose is correctly in- 1. Verify that the signal light for presence of the serted in the proper seat on the recovery tank. tension (5) is on, if necessary, check that the plug 4. -
Page 11: Programmed Maintenance
Pad holder is recommended to clean smooth surfaces. It has anchor points which permit the blocking of the abrasive pad during work. MACHINE CODE QUANTITY DESCRIPTION ruby 45e 48901010 Brush PPL 0,3 Ø 235 Irregular floors with large joints. 48901020 Brush PPL 0,4 Ø 235 Normal floors.