Related Manuals for Knox Video QF-045
Summary of Contents for Knox Video QF-045
- Page 1 RSII Routing Switcher System Operation and Technical Manual KNOX VIDEO TECHNOLOGIES 8547 Grovemont Circle QF-045 Gaithersburg, MD 20877 TEL 301•840•5805 RSII Series Manual FAX 301•840•2946 Rev. 04/01/2007 www.knoxvideo.com...
- Page 2 KNOX VIDEO RSII Routing Switcher System Control via the Serial RS232/RS422 Port or Ethernet Port ........10 RSII 3.5.1 Using an RS232/RS422...
- Page 3 Warnings, Cautions and Others NOTES Mises en garde, precautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
-
Page 4: Limited Warranty
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND. IF SERVICE IS REQUIRED: If the product does not perform as warranted, call Knox Video Technologies For Canada/pour le Canada at 301-840-5805 for available service options. -
Page 5: Table Of Contents
KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System TABLE OF CONTENTS SECTION 4. MAINTENANCE Section 1. GENERAL INFORMATION Introduction ......... 1 Technical Description . -
Page 6: Section 1. General Information Introduction
KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System SECTION 1. GENERAL INFORMATION 1.1 INTRODUCTION $M0, 1 Mute off/on $L0, 1 Loudness off/on The KNOX RSII AUDIO/VIDEO ROUTING SWITCHER is a family of de- $Ixx Set input trim level vices, which accepts up to sixteen video sources and sixteen stereo audio sources. - Page 7 KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System Output Impedance: 75 ohms 3.4.9 COMMAND SUMMARY Crosstalk: less than -70dB@5MHz Connectors: 75ohm female BNC for Composite, 4 pin DIN for Bxyz/Bxxyyzz Both Vxy/Vxxyy Video Vertical interval switching with video on External Sync BNC...
- Page 8 KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System 3.4.8 ADDITIONAL SOUND CONTROL COMMANDS Audio Channels: $ci clears all input trims Levels: $cxxi clears input trim for input xx Unbalanced audio: 3v p-p unbalanced audio $c sets all VTB for all outputs to default* values...
-
Page 9: Section 2. Installation
KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System SECTION 2. INSTALLATION To control balance between the left and right channels send a command of the form: $Sxx+, $Sxx-, or $Sxx0, where 0 resets balance to equal (+ decreases left 2.1 INTRODUCTION... -
Page 10: Video Connections
KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System 2.4 VIDEO CONNECTIONS 3.4.5 HOW TO STORE AND RECALL CROSSPOINT PATERNS Connect up to sixteen video SOURCES (cameras, VCRs, DVD players, satel- The RSII has 17 stored routing patterns. Sixteen patterns for typical use and lite receivers, RF demodulators, etc) to the video input connectors. -
Page 11: Rs232 Connections
KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System 2.6 RS232 CONNECTIONS 3.4.3 USING THE SALVO MODE It is possible to send the same input to a number of sequential outputs by a The RSII can be controlled by external RS232 drivers connected to either or... -
Page 12: Ethernet Connections
01-16, and where y specifies the NOTE: The default IP address by Knox Video is 192.168.168.48 source of video, 00-16 (use 0’s for video OFF)To route audio only, send a four- with a subnet mask of 255.255.255.0... -
Page 13: Setting Up Hyperterminal As A Serial Controller
DB9 serial connector will accept RS232 serial data only.A simple ASCII protocol allows all crosspoint and setup commands to be sent serially through the RSII’s 4) At this point you can open Hyper Terminal and verify the Knox Video RS232/RS422 or Ethernet ports. These ports will accept commands from a terminal, switch functionality. -
Page 14: Section 3. Operation
KNOX VIDEO KNOX VIDEO RSII Routing Switcher System RSII Routing Switcher System SECTION 3. OPERATION 3.3.2 CHANGING A CROSSPOINT CONNECTION You can make crosspoint changes with the 16 input buttons and 16 output 3.1 INTRODUCTION buttons on the right. You may start with an input number or with an output This section explains in detail the operation of the RSII using either the De- number, then push the connection you want to make.
Need help?
Do you have a question about the QF-045 and is the answer not in the manual?
Questions and answers