Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Installation Guide
Backup Battery Option Kit
Series 4000
Instructions for installing the optional backup battery in the
Series 4000 badge timeclock
®
Document Part Number: 4702572-002
Document Revision: B
Advertisement
Related Manuals for Adp Series 4000
Summary of Contents for Adp Series 4000
- Page 1 Installation Guide Backup Battery Option Kit Series 4000 Instructions for installing the optional backup battery in the Series 4000 badge timeclock ® Document Part Number: 4702572-002 Document Revision: B...
- Page 2 The ADP Logo is a registered trademark of ADP of North America, Inc. Enterprise eTIME is a trademark and eTIME is a registered trademark of Automatic Data Processing, Inc.
- Page 3 When using and applying the information generated by ADP products, customers should ensure that they comply with the applicable requirements of federal and state law, such as the Fair Labor Standards Act. FCC Compliance After testing, this equipment complies with the limits for a Class A digital device pursuant to Part 15 of FCC Rules.
- Page 5 Cable to connect the charger board to the Series 4000 timeclock’s main board It takes 24 hours for the Series 4000 timeclock to charge the backup battery after you install it. Also, if the battery ever becomes depleted (completely discharged) from use, allow 24 hours for the timeclock to recharge the battery.
-
Page 6: Before You Begin
Before you begin, please read the following: Your installation scenario Instructions to follow You are about to install the Series 1. Follow the instructions in the Series 4000 Badge 4000 timeclock to include the backup Timeclock Installation Guide (that shipped with the battery. - Page 7 Preparing an Installed Series 4000 Timeclock for Battery Installation If you have already installed the Series 4000 timeclock, do the following before you install the backup battery: 1. If necessary, collect data from the timeclock using your host application software.
- Page 8 Preparing an Installed Series 4000 Timeclock for Battery Installation 5. Remove the transformer from the timeclock. To do this: a. Trace the cable back to the transformer, freeing the cable from the routing channel in the timeclock. b. Carefully lift the transformer up and out from behind the wire transformer clip, and out of the timeclock.
- Page 9 Preparing an Installed Series 4000 Timeclock for Battery Installation 7. If you are replacing an existing backup battery, perform the following steps. Otherwise, proceed to “Installing the Backup Battery Option,” beginning on page 8. a. Disconnect the battery charger board from the timeclock’s main board.
- Page 10 Preparing an Installed Series 4000 Timeclock for Battery Installation c. Disconnect the battery charger board from the positive and negative terminals of the backup battery. Number Description Hooks molded into the base Negative terminal connection (black) Positive terminal connection (red) d.
- Page 11 Preparing an Installed Series 4000 Timeclock for Battery Installation e. Remove the battery from the base of the timeclock. Mlinst39 You are now ready to install the new backup battery. Proceed to “Installing the Backup Battery Option,” beginning on page 8.
- Page 12 The illustrations also show the timeclock mounted to cover an AC outlet. However, this procedure applies to all power source scenarios. 1. If you are installing the Series 4000 timeclock and have mounted the base to the wall, perform this step.
- Page 13 Installing the Backup Battery Option 2. Position the battery in the base of the timeclock as shown. Number Description Negative battery terminal (black) Positive battery terminal (red) Molded hooks to hold the battery in place Backup Battery Option Kit Installation Guide...
- Page 14 Squeeze the clip to lock it into position under the two molded hooks in the base. 4. Plug the cables that came with the battery into the connectors on the charger board. Match the ends of each cable with the pin connectors on the board. ADP, Inc.
- Page 15 Installing the Backup Battery Option 5. Position the charger board in the base and secure it with the supplied screw. 6. Connect the charger board to the positive and negative terminals of the backup battery. Use the hooks molded into the base of the timeclock to secure the cable along its route. Number Description Cable routing hooks...
- Page 16 Installing the Backup Battery Option Note If you are in the process of installing the Series 4000 timeclock, return to the Series 4000 Badge Timeclock Installation Guide and continue with “Installing the Transformer” in Chapter 2. If you are adding or replacing the battery in your installed timeclock, continue with this procedure.
-
Page 17: What To Do Next
What To Do Next What To Do Next To continue assembling the timeclock, return now to the Series 4000 Badge Timeclock Installation Guide and continue with “Installing the Transformer” in Chapter 2. Backup Battery Option Kit Installation Guide... - Page 18 What To Do Next ADP, Inc.
Need help?
Do you have a question about the Series 4000 and is the answer not in the manual?
Questions and answers