KDC-8026/MP825 KDC-MPV8025/W7027 BLOCK DIAGRAM AUX IN (X34- ) Q207,208 IC13 PRE OUT TUNER PRE MUTE OP AMP (SUB WOOFER) AUDIO OUT Q203,204 Q303,304 IC12 E-VOL SYSTEM PRE OUT & AM+B PRE MUTE OP AMP E'S+ (REAR) Q205,206 IC11 PRE OUT...
KDC-8026/MP825 KDC-MPV8025/W7027 MICROCOMPUTER’S TERMINAL DESCRIPTION Pin No. Pin Name Description / Processing Operation LX CON External slave unit (ON : H, OFF : L) LX RST Reset output to external slave unit (Normal : L, After system reset : H 400ms or more and then L) CD MECHA+B CD4.7V output terminal (CD : H, Except CD source : L)
Page 7
KDC-8026/MP825 KDC-MPV8025/W7027 MICROCOMPUTER’S TERMINAL DESCRIPTION Pin No. Pin Name Description / Processing Operation NOISE FM noise detection terminal IFC OUT Front end IFC OUT input terminal (Receiving station : 2.5V or more) POWER DET Audio power IC DC offset detection...
Page 8
KDC-8026/MP825 KDC-MPV8025/W7027 MICROCOMPUTER’S TERMINAL DESCRIPTION Pin No. Pin Name Description / Processing Operation 0bit muting detect (Lch) L : MUTE OFF, H : MUTE ON 0bit muting detect (Rch) L : MUTE OFF, H : MUTE ON 14,15 20CS Chip select signal output terminal (for decoder)
Page 9
KDC-8026/MP825 KDC-MPV8025/W7027 MICROCOMPUTER’S TERMINAL DESCRIPTION Pin No. Pin Name Description / Processing Operation ESRST Reset signal output terminal (for ES3890) L : RESET, H : NORMAL VMUTE Video mute control terminal H : MUTE ON, L : MUTE OFF NC (OPEN)
KDC-8026/MP825 KDC-MPV8025/W7027 TEST MODE How to enter the test mode Test mode specifications of the CD receiver While pressing and holding the Preset 1 and Preset 3 keys, • Forced ejection is inhibited in the reset start operation. When reset the unit.
Page 11
KDC-8026/MP825 KDC-MPV8025/W7027 TEST MODE Menu-related specifications AM key Display panel E2PROM condition. • A short press of the Q key initiates the menu mode. (Display) P–ROM OK (Registered code) • Pressing the DNPP key on the remote initiates the Menu P–ROM NG (Code is write in error)
Page 12
KDC-8026/MP825 KDC-MPV8025/W7027 TEST MODE Security information 3. How to inscription the panel security code 1. Forced Power ON mode (All models) 1. Enter the test mode. 2. Pressing the AM key on all lighting, check the “P-ROM WAIT” Even when the security (Cord) is approved, resetting the display.
Page 13
KDC-8026/MP825 KDC-MPV8025/W7027 PC BOARD (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) DISPLAY UNIT DISPLAY UNIT X16-2540-10 (J74-1588-02) X16-2540-10 (J74-1588-02) ILLGND R51 R52 E2PCLK E2PDATA PANDET DATAS DATAL DGND REMO X16-2540-10 Ref. No. Address X16-2540-10 Ref. No. Address C13 C29 Refer to the schematic diagram for the values of resistors and capacitors.
Page 18
KDC-8026/MP825 KDC-MPV8025/W7027 PC BOARD (COMPONENT SIDE VIEW) CD PLAYER UNIT X32-5540-00 (J74-1552-12) RFOK CP12 CP13 CP15 MIACK X32-5540-00 Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 19
KDC-8026/MP825 KDC-MPV8025/W7027 PC BOARD (FOIL SIDE VIEW) CD PLAYER UNIT X32-5540-00 (J74-1552-12) Vref FLAG HOLD MIRR LOCK TRK IN TRK OUT FCS DOWN FCS UP C22 C23 D3.3V DAVdd3.3V SDIO BCKIA 12EJE A.+8V LRCKIA /EJECT SLED IN SLED OUT A.GND...
Page 20
KDC-8026/MP825 KDC-MPV8025/W7027 PC BOARD (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) DISPLAY UNIT DISPLAY UNIT X16-2550-10 A/3 (J74-1589-02) X16-2550-10 A/3 (J74-1589-02) X16 C/3 X16 C/3 CP53 ILL-GND X16 B/3 X16 B/3 VLCD1 D-GND CP55 CP56 L-CE L-DATAS VOL-B VOL-A X16-2550-10 Ref. No.
Page 26
KDC-8026/MP825 KDC-MPV8025/W7027 LCD DRIVER & KEY INPUT LCD DRIVER SWITCH UNIT (X16-2080-10) GND LINE MODEL NAME UNIT No. B LINE KDC-7027/Y PAN-DET KDC-8026 X16-2540-10 KDW-MP825 LC75808W KDC-W7027 LC75878W PNA4S22M Q1,6 DTA114EE : UMX2N Q5,11 2SC4617 MA3062-M 5.0V D2-5 DA204U B30-2233-05...
Page 27
2SC4617 2SD2114K 2SB1188 2SC4081 UMX2N DTA114EUA DTA124EUA DTC124EUA DTC144EUA KDC-8026/MP825/W7027 (2/3) DAN202U CAUTION : For continued safety, replace safety critical components only with manufacturer’s recommended parts (refer to parts list). 40-10 DAP202U Indicates safety critical components. To reduce the DA204U...
Page 29
KDC-8026/MP825 KDC-MPV8025/W7027 LCD DRIVER & KEY INPUT LCD DRIVER SWITCH UNIT (X16-2080-10) PAN-DET GND LINE B LINE LC75808W Q1,6 DTA114EUA or LC75878W UN5111 PNA4S22M Q2,11-16 : UMX2N M62333FP Q5,62-64 2SC4617 5.0V MA3062-M D2-5 DA204U EEP ROM B30-2233-05 MA3091-M D50-53 B30-1599-05...
Page 30
KDC-8026/MP825 KDC-MPV8025/W7027 MA142WA UN5212 RD6.8M TC74HC02AF TC7SH08FU M5237ML LB1930M TDA7479D KDC-MPV8025 (2/3) CAUTION : For continued safety, replace safety critical components only with manufacturer’s recommended parts (refer to parts list). Indicates safety critical components. To reduce the risk of electric shock, leakage-current or resistance mea-...
Page 31
KI4 7 NC 11 X16-254- X16-255- VOL-B VOL-A D GND PAN-5V ILL +B ILL +B ILL-GND ESD GND OPEN VOLUME KDC-8026/MP825/MPV8025/W7027 (3/3) (X16-256x-xx) UNIT C1-5, D11-15, : DTA114YUA R1,2 R3,4 MODEL NAME D1-10 R6-10 7-12 17-22 Q2-4 : 2SD2114K KDC-X979/X879...