Page 1
CS60EVO Sectional Garage Door Opener Installation and Operating Instructions Owners Copy: SAVE THESE INSTRUCTIONS for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY...
WARNING! START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service, provided it is installed and operated in strict accordance with the instructions in this manual.
If your door binds, sticks, or is out of balance, call a trained door technician. DOOR TYPES Sectional Door with curved track (MAX. door height 2.2 m) PowerLift - CS60EVO: To suit spring balanced Sectional doors up to 12.0 m Electrical Connection A 240 V General Purpose Outlet (GPO) ie.
CARTON INVENTORY Your garage door opener and rail are packed in a single carton. The PowerLift CS60EVO opener cartons contain the opener, the rail, its fitting hardware and accessories. (1) Opener (9) Hardware bag (2) Hand held transmitter x 1...
CONTROL PANEL (located under the cover at the rear of the opener) 1. External Accessory Power: 30 Vdc 50 mA available for universal receiver (not active in Low standby mode). 2. Terminal Block: used for external accessories (see chart below). Function Colour Polarity Comment E-Serial port...
ASSEMBLY SECTION ASSEMBLING THE 4 PIECE SEGMENTED RAIL The segmented rail is largely preassembled and consists of 4 parts. The carriage, push rod, release handle, the guide pulley and the lintel bracket with belt tensioner are in the front part (A). The seating for the drive shaft and the sprocket are in the rear part (B).
INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to the garage door. To avoid serious personal injury from entanglement, remove all ropes connected to the garage door before installing the opener.
POSITION THE OPENER Disengage the trolley mechanism (see section “Operating the manual release”) and slide it back towards the powerhead. Secure the hanging push arm up into the rail assembly temporarily using tape or rope, to avoid a hazard. SECTIONAL DOOR You will need a 50 mm piece of timber or similar spacer to gauge the distance between door and rail.
Page 10
HANG THE OPENER The opener must be securely fastened to a sound structural support above the opener. fig.1 1.Postion the opener as in the previous step. Check the rail is centred over the door. Ensure the rail brackets (fig.1) is on the Powerhead end of the rail in a position as close to the opener as possible (X).
Make sure the garage door is fully closed. Pull the manual release ATTACH DOOR ARM TO TROLLEY cord to disengage the trolley. Slide the trolley to around 300 mm Fig. 1 Fig. 2 from the header bracket. 1.The straight door arm is already preassembled to the trolley. 2.Install the curved arm onto the door bracket using the Clevis pin (2) and R-Clip (3) supplied.
ADJUSTMENT SECTION Travel limits regulate the points at which the door will stop PROGRAM THE TRAVEL LIMITS AND FORCE SETTINGS Without a properly installed safety reversal when moving UP or DOWN. The travel limit buttons are located system, persons (particularly small children) under the access cover on the rear panel (figure 1).
Page 13
TEST THE SAFETY REVERSE SYSTEM The safety reverse system test is important. Garage door must reverse on contact with a 40 mm obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door.
INSTALL THE PROTECTOR SYSTEM (OPTIONAL) NOTE: This accessory must be used for all installations To prevent entrapment, install The Protector where the closing force as measured on the bottom of the System™ no higher than 100 mm above the floor. door is over 400 N (40 kgf).
TIMER TO CLOSE FEATURE (TTC) Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. figure 1 The Timer to Close feature requires The Protector System (IR Beams) to be installed. Indicator LED Operation: This feature allows the door to automatically close from a fully open position after a specified time.
INSTALL WARNING LABELS For Service Call RISK OF ENTRAPMENT Installation Date Repeat Safety Reverse Test monthly. Door 114A3361 must reverse on contact with a 40mm obstacle For Service Call placed on the floor. Make necessary adjustments. AUTOMATIC DRIVE: Keep away from the area of the door since it may operate unexpectedly.
WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES) Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door.
MAINTENANCE AND CARE OF YOUR OPENER Battery of the remote control: USING YOUR OPENER REPLACE BATTERIES IN REMOTES 1. Your opener can be activated by any of the following devices: • Opener control panel: Up and Down Buttons. The batteries in the remote have an extremely long life. •...
ACCESSORIES Model E950C 2 Channel remote control Model E1702M Quick release lock Model E940C 1 Channel visor remote control Model 760AML Outside keyswitch Model 770AML The Protector System E1702M 760AML E950C E940C 770AML...
TROUBLE SHOOTING 1. Opener doesn't operate from either door control or 7. Door opens but won't close: remote: • Check The Protector System™ (if you have installed • Does the opener have electric power? Plug lamp into this accessory). If the light on the Beams are flashing, outlet.
Page 21
DIAGNOSTIC CHART Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage opener flash the diagnostic codes. DIAGNOSTIC CODE SYMPTOM POSSIBLE RESOLUTION UP Arrow DOWN Arrow Flash(es) Flash(es) The garage door opener will not Safety sensors are not installed, connected or wires may be cut.
SPECIFICATIONS - PowerLift - CS60EVO Input Voltage...230-240 Vac, 50 Hz Max. Pull Force ..600 N Power .....150 Watt Standby Power ..0.8 Watt (door fully closed) Normal Torque ..5 Nm Max door weight..70 kgs Spring balanced Max door area..Sectional door 12 m Motor Type......DC gearmotor permanent lubrication...
Chamberlain warrants to the original purchaser of the: 6 water or moisture ingress that causes corrosion or electrical malfunction; Chamberlain PowerLift CS60EVO Sectional Door Opener (Unit) that it is 7 corrosion caused by sea air if located near a waterway, beach etc;...