Table of Contents
Advertisement
How to connect the COMPONENT/RGB Input Terminals
Component signals (Y, P
, P
) connection
B
R
DVD Player
Audio
DVD (Y,P
B
, P
R
) OUT
OUT
R
L
Y
P
P
B
R
Y, P
, P
B
R
3 RCA
video cables
AUDIO
2 RCA audio cables
Notes:
(1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "Y/PB/PR". (see page 30, 32)
(2) Additional equipment and cables shown are not supplied with this set.
RGB signal (R, G, B, HD, VD) connection
Example of input signal source
RGB input to
R, G, B, HD, VD sockets
HDTV-compatible VCR
5 BNC
RGB cables
or
RGB camera
VD
HD
AUDIO
2 RCA audio cables
Audio input to
L/R sockets
Notes:
(1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "RGB". (see page 30, 32)
(2) Additional equipment and cables shown are not supplied with this set.
Connections
L
AUDIO
VD
HD
P
R
/C
R
/R
P
B
/C
B
/B
Y/G
R
COMPONENT/RGB IN
RCA-BNC
adapter plug
Audio input to L/R sockets
L
AUDIO
VD
HD
P
/C
/R
P
/C
/B
Y/G
R
R
B
B
R
COMPONENT/RGB IN
15
Connections
How to connect the PC Input Terminals
COMPUTER
Conversion adapter (if necessary)
Connect a cable which matches
the audio output terminal on the computer.
Notes:
(1) Computer signals which can be input are those with a horizontal scanning frequency of 15.5 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, signals cannot be displayed if signals exceeding 1200 lines will not
be displayed properly.)
(2) The display resolution is a maximum of 1024
768 dots when the aspect mode is set to "NORMAL", and 1366
dots when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be
possible to show fine detail with sufficient clarity.
(3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you
will need to make setting changes to the computer at the time of connection.
(4) Some PC models cannot be connected to the set.
(5) An adapter is required to use the PC cable (D-sub 15P) to connect a Macintosh computer to the set.
(6) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.
(7) The computer shown in the illustration is for example purposes only.
(8) Additional equipment and cables shown are not supplied with this set.
(9) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
Signal Names for D-sub 15P Connector
Pin No.
Signal Name
11
12
13
14
15
1
R
6
7
8
9
10
2
G
1
2
3
4
5
3
B
4
GND (Ground)
Pin layout for PC input
5
GND (Ground)
terminal
16
AUDIO
PC IN
POWER
/
R - STANDBY
INPUT
–
VOL
+
G POWER ON
D-sub 15p
RGB
PC cable
Audio
1/8" (3mm) stereo plug
768
Pin No.
Signal Name
Pin No.
Signal Name
6
GND (Ground)
11
GND (Ground)
7
GND (Ground)
12
SDA
8
GND (Ground)
13
HD/SYNC
9
NC (not connected)
14
VD
10
GND (Ground)
15
SCL
Advertisement
Table of Contents
