Advertisement
INSTALLATION, OPERATION
AND MAINTENANCE
CE SERIES
12, 15 & 18kW
208V, 240V, 480V
SINGLE & THREE PHASE
CHECK ALL ELECTRICAL CONNECTIONS TO ALL COMPONENTS
WITHIN THE HEATER FOR TIGHTNESS. CONNECTIONS CAN
BECOME LOOSE DURING SHIPMENT AND HANDLING.
THE ELECTRICAL INSTALLATION MUST BE IN ACCORDANCE
WITH ARTICLE 680 OF THE NATIONAL ELECTRICAL CODE.
Only qualified personnel, as defined by National Electric Code Article
100, should install and maintain this equipment. Unauthorized
alteration or improper maintenance of this unit may release the
manufacturer from any warranty claims. The installation must be in
accordance with the instructions in this manual and applicable local
POOL HEATER
MODELS:
CPH SERIES
24 & 30kW
208V, 240V, 480V
SINGLE & THREE PHASE
BEFORE YOU BEGIN
CAUTION
WARNING
plumbing and electrical codes.
PHS SERIES
36, 45, 54 & 57kW
208V, 240V, 480V
SINGLE & THREE PHASE
Publication 2/06
Advertisement
Table of Contents
Related Manuals for Coates CE Series
Summary of Contents for Coates CE Series
- Page 1 POOL HEATER INSTALLATION, OPERATION AND MAINTENANCE MODELS: CE SERIES CPH SERIES PHS SERIES 12, 15 & 18kW 24 & 30kW 36, 45, 54 & 57kW 208V, 240V, 480V 208V, 240V, 480V 208V, 240V, 480V SINGLE & THREE PHASE SINGLE & THREE PHASE SINGLE &...
-
Page 2: Installation Location
In order to help maintain Coates swimming pool heaters are quiet, do not expel the heater in a satisfactory manner, a brief description exhaust fumes, and may be conveniently located in shed of its components and their operation is included for or basement. -
Page 3: Installation: Plumbing
Installation: Plumbing 125% of the ampere rating shown on heater nameplate. Refer to Table 1 for wire sizes. Connect power conductors to the power distribution block inside the Pipe the heater as shown in Figure 2 to the inlet and heater. -
Page 4: Start-Up Procedure
Startup Procedure: MAINTENANCE 1. Make sure that the pump is on and that there is at Element Inspection and Replacement: least 20 GPM flow through the pool heater. The 1. Turn off power at main disconnect switch and turn heating elements will fail if allowed to operate dry. off pump. - Page 7 HEATER GROUND TERMINAL ENCLOSURE POOL GROUND GROUND BRASS COPPER ISOLATED BUS FLOW SWITCH ALUMINUM TB1 FOR REMOTE TEMPERATURE CONTROL (IF USED). SEE INSTRUCTION MANUAL FOR COMPONENT IDENTIFICATION. ALL WIRING TO BE 105°C INSULATED, MINIMUM. CONTROL CIRCUIT WIRING; 14 AWG. POWER CIRCUIT WIRING; AS NOTED. LEGEND;...
- Page 10 HEATER GROUND TERMINAL BRASS ENCLOSURE POOL COPPER GROUND GROUND ALUMINUM FLOW SWITCH TB1 FOR REMOTE TEMPERATURE CONTROL (IF USED). ISOLATED BUS SEE INSTRUCTION MANUAL FOR COMPONENT IDENTIFICATION. ALL WIRING TO BE 105°C INSULATED, MINIMUM. PL2 "FLOW" CONTROL CIRCUIT WIRING; 14 AWG. POWER CIRCUIT WIRING;...
- Page 11 HEATER GROUND TERMINAL 120V ENCLOSURE POOL GROUND GROUND BRASS COPPER ALUMINUM FLOW SWITCH SEE INSTRUCTION MANUAL FOR COMPONENT IDENTIFICATION. ALL WIRING TO BE 105°C INSULATED, MINIMUM. CONTROL CIRCUIT WIRING; 14 AWG. PL2 "FLOW" POWER CIRCUIT WIRING; AS NOTED. LEGEND; PL1 "ELEMENT" R = RED B = BLACK W = WHITE...
- Page 14 HEATER GROUND TERMINAL 120V ENCLOSURE POOL GROUND GROUND BRASS COPPER ALUMINUM FLOW SWITCH TB1 FOR REMOTE TEMPERATURE CONTROL (IF USED). SEE INSTRUCTION MANUAL FOR COMPONENT IDENTIFICATION. ALL WIRING TO BE 105°C INSULATED, MINIMUM. CONTROL CIRCUIT WIRING; 14 AWG. PL2 "FLOW" POWER CIRCUIT WIRING;...
- Page 15 HEATER GROUND TERMINAL 120V ENCLOSURE POOL GROUND GROUND BRASS COPPER ALUMINUM FLOW SWITCH TB1 FOR REMOTE TEMPERATURE CONTROL (IF USED). SEE INSTRUCTION MANUAL FOR COMPONENT IDENTIFICATION. ALL WIRING TO BE 105°C INSULATED, MINIMUM. CONTROL CIRCUIT WIRING; 14 AWG. PL2 "FLOW" POWER CIRCUIT WIRING;...
-
Page 16: Limited Warranty
Coates Heater Company, Inc. or to any product where the nameplate shall have been removed, altered, replaced, defaced or rendered illegible.
Need help?
Do you have a question about the CE Series and is the answer not in the manual?
Questions and answers