Table of Contents
Advertisement
Quick Links
O
PERATOR
S
AND
ERVICE
MM60
MM80
MM90
This manual covers the following serial numbers
and higher for each model listed:
MM60 . . . . . . . . . . . . . . . . . . . . 7011600
MM80 . . . . . . . . . . . . . . . . . . . . 7032000
MM90 . . . . . . . . . . . . . . . . . . . . 7051100
M
& P
ORTAR
MBW, Inc.
250 Hartford Rd • PO Box 440
Slinger, WI 53086-0440
Phone: (262) 644-5234
Fax: (262) 644-5169
Email: mbw@mbw.com
Website: www.mbw.com
'
S
S
AFETY
M
ANUAL
M
LASTER
MBW (UK) Ltd.
Units 2 & 3 Cochrane Street
Bolton BL3 6BN, England
Phone: 01204 387784
Fax: 01204 387797
IXERS
MBW FRANCE S.A.R.L.
Z.A. d'Outreville
11 rue Jean Baptiste Néron,
60540 BORNEL
FRANCE
Phone: +33 (0) 3 44 07 15 96
Fax: +33 (0) 3 44 07 41 28
Email: mbwfrance@free.fr
L16746. 04.14.T
©MBW, Inc. 2005
Printed in the USA
Advertisement
Table of Contents
Related Manuals for MBW MM60
Summary of Contents for MBW MM60
- Page 1 MM60 ....7011600 MM80 ....7032000 MM90 .
-
Page 2: Table Of Contents
ABLE ONTENTS Safety Information ..... . 1 Lubrication ....... . . 8 Belt Guides. - Page 3 WARNING CALIFORNIA PROPOSITION 65 WARNING Engine exhaust and some of its constituents are known in the state of California to cause cancer, birth defects, and other reproductive harm.
-
Page 4: Safety Information
MBW does monoxide, a poisonous, odorless, invisible not by the publication of these precautions, imply or in any gas. Death or serious illness may result if way represent that these are the sum of all dangers present inhaled. - Page 5 CAUTION(PRECAUCIÓN) CAUTION(PRECAUCIÓN) Improper towing can lead to damage or injury. Read the operating instructions before operating this piece of equipment. Before Towing: Lea las Instrucciones Operativas antes de hacer funcionar esta parte del equipo. 1. Check running gear and tow bar. 2.
- Page 6 WARNING ADVERTENCIA WARNING ADVERTENCIA ENGINE EXHAUST IS HAZARDOUS IF INHALED 12500 USE ONLY IN A WELL VENTILATED AREA EL GAS DEL ESCAPE DEL MOTOR ES PELIGROSO SI SE INHALA USE LA MÁQUINA SÓLO EN UNA ZONA BIEN VENTILADA 15076 15076 MOVING PARTS CAN CRUSH AND CUT KEEP HANDS CLEAR! SHUT OFF ENGINE OR MOTOR...
- Page 7 :$51,1* 527$7,1* 3$576 .HHS KDQGV DZD\ 12573 MIXER(MEZCLADORA) OPERATING INSTRUCTIONS INSTRUCCIONES DE OPERACIÓN Check oil in engine crankcase. MAKE SURE grid is CLOSED before starting and during operation. Place engage lever in “IDLE” position before starting engine. Open fuel valve. Close choke on engine.
-
Page 8: Specifications
PECIFICATIONS MM60 MM90 MM60 MM80 MM90 Batch Capacity 6 cu. ft (.17 cu. m) 8 cu. ft (0.23 cu. m) 9 cu. ft (0.26 cu. m) Batch Size 2 bags 2.5 - 3 bags 3 - 3.5 bags Honda GX160... -
Page 9: Operation
Pull out the stop switch on the engine shroud. Move the engine throttle lever to the “FAST” position. MBW equipment is intended for use in very severe applications. They are powered by four cycle engines and Choke the engine if necessary. (You may not need to are available in different sizes and a selection of engines. -
Page 10: Stopping Electric Motor
Close the fuel valve. Rotate the drum into the locked position, and check that it is locked in place. Stopping Electric Motor Secure the mixer hitch and safety chains to the vehi- cle. Move mixer engagement lever to the “IDLE” position. Move the switch on the motor to the “OFF”... -
Page 11: Maintenance
AINTENANCE WARNING CAUTION Always exercise the stopping procedure before Always verify fluid levels and check for leaks after servicing or lubricating the unit. changing fluids. After servicing the unit, replace and fasten all Do not drain oil onto ground, into open streams, guards, shields, and covers to their original or down sewage drains. -
Page 12: Belt Guides
Greasing Wheel Bearings FIGURE 1 Jack the rear end of the mixer and support by side GREASE DAILY rails so that mixer is stable. Remove the wheel. Remove the dust cover. Remove the cotter pin from the spindle nut. OIL WEEKLY Unscrew the spindle nut. -
Page 13: Service
ERVICE Assembly and disassembly should be performed by a Engine Shroud Removal service technician who has been factory trained on MBW Refer to Drivetrain Assembly, page 16. equipment. The unit should be clean and free of debris. Pressure washing before disassembly is recommended. -
Page 14: Drum Bearing & Seals Replacement
Check alignment between bull gear and pinion. 16. Slide bearing locking collar onto front shaft end and Gears must be parallel and in-line. Adjust drum loca- align shaft flush with collar. tion if necessary. 17. Lock collar in place by driving in the mixing direction. Bolt pillow blocks to frame using four bolts (#25), 18. -
Page 15: Parts Replacement Cycles And Tolerances
Parts Replacement Cycles and Tolerances Replace anytime a bearing is rough, binding, discolored or removed from housing or Bearings shaft. Clutch Replace clutch if it does not disengage below 1800 rpm. Engine Components Refer to your engine manufacturer’s Owner’s Manual. Replace any worn or damaged hardware as needed. -
Page 16: Replacement Parts
Their sales engineers are avail- able for professional consultation. If you cannot locate an M-B-W distributor in your area, contact MBW, Inc. or one of our Sales Branches listed below. When ordering replacement parts, be sure to have the fol- lowing information available: •... -
Page 17: Drum Assembly
Drum Assembly - 14 -... - Page 18 05918 SEAL KIT 06327 WASHER 16737 HANDLE, DUMP 16806 GRID, MM60 16807 GRID, MM80 16781 GRID, MM90 16832 OPENER, GRID, MM60 16782 OPENER, GRID 17076 DRUM, MM60 17077 DRUM, MM80 17078 DRUM, MM90 17079 LOCKING BAR 18903 GRIP, DUMP HANDLE F051808HCS HEX HEAD CAP SCREW, 5/16-18 x 1”...
-
Page 19: Drivetrain Assembly
5.5 HP HONDA Drivetrain Assembly - 16 -... - Page 20 ITEM PART NO. DESCRIPTION 01159 KEY, 3/8” SQUARE x 3” LONG 01160 KEY, 1/4” SQUARE x 2” LONG 01561 SHEAVE, 2A - 4” (8 hp Honda) 01562 SHEAVE, 2A - 8” 01563 SPUR GEAR, 84 TOOTH 05586 BEARING, PILLOW BLOCK 05692 SHIM, MIXER (AS REQUIRED) 05741...
-
Page 21: Electric Motor Drivetrain Assembly
Electric Motor Drivetrain Assembly - 18 -... - Page 22 ITEM PART NO. DESCRIPTION 01160 KEY, 1/4” SQUARE x 2” LONG 01283 KEY, 1/4” SQUARE x 1-1/4” LONG 01561 SHEAVE, 2A - 4” 19876 SHAFT, INTERMEDIATE 05586 BEARING, PILLOW BLOCK 16585 SPROCKET, 60 TOOTH 06067 MOTOR, ELECTRIC 1.5 HP, 1-PHASE, 230 VOLT 19918 MOTOR, ELECTRIC 1.5 HP, 1-PHASE, 115 VOLT 06025...
-
Page 23: Idler Assembly
Idler Assembly - 20 -... - Page 24 ACTUATOR 16736 ARM, IDLER 16887 SWIVEL ASSEMBLY 16784 PULLEY, FLAT IDLER 16786 JOINT, BALL 16828 ENGAGEMENT HANDLE, MM60 16829 ENGAGEMENT HANDLE, MM80 16752 ENGAGEMENT HANDLE, MM90 16933 SPRING, COMPRESSION F042012HCS HEX HEAD CAP SCREW, 1/4-20 x 1-1/2” F0420ELN ELASTIC LOCKNUT, 1/4-20 F042856HCS HEX HEAD CAP SCREW, 1/4-28 x 7”...
-
Page 25: Air Mixer Assembly
Air Mixer Assembly - 22 -... - Page 26 ITEM PART NO. DESCRIPTION 01160 KEY, 1/4 SQ X 2 01204 CHAIN, CONNECTING LINK #50 01239 NIPPLE 01283 KEY, 1/4 SQ X 1-1/4 RD ENDS 01561 SHEAVE, TWO GROOVE 2AK44 X 1 06065 CHAIN, ROLLER #50 X 35-1/2 06116 FITTING, PIPE REDUCER 1 X 3/4 08280 FITTING, PIPE 90 DEG STREET X 1 08910...
-
Page 27: Frame & Axle Assembly
Frame & Axle Assembly - 24 -... - Page 28 LEG, FRONT 16771 CHAIN, SAFETY (10 ft.) 16817 AXLE, 12” WHEELS (Includes hubs) 16818 AXLE, 13” WHEELS (Includes hubs) 17073 FRAME, MM60 17074 FRAME, MM80 17075 FRAME, MM90 17158 HAIRPIN, 5/32” x 2-11/16” LONG F0210CP COTTER PIN, 1/8” x 1-1/4”...
-
Page 29: Paddle Assembly
TO ENGINE TO ENGINE MM90 PADDLE ORIENTATION Paddle Assembly - 26 -... - Page 30 ITEM PART NO. DESCRIPTION 05821 MAIN SHAFT, MM60 05006 MAIN SHAFT, MM80 05648 MAIN SHAFT, MM90 17574 RUBBER BLADE, END* 18540 STEEL BLADE, END 17576 RUBBER BLADE, CENTER* 18543 STEEL BLADE, CENTER 17578 RUBBER BLADE, WIPER* 18544 STEEL BLADE, WIPER...
-
Page 31: Warranty
1.This warranty does not cover any Used Equipment. "Used Equipment" such replacement or repair is the exclusive remedy provided hereunder. means any MBW machine or equipment that is not a New Machine or a Labor must be performed at an authorized MBW distributor. MBW Demonstration Machine. - Page 32 NOTES:...
- Page 33 NOTES:...