Table of Contents
Advertisement
INSTALLATION INSTRUCTIONS
Product
Docking Staton - Getac B300 USB 3.0
7160-0526-00 No RF
7160-0526-02 Dual RF
7160-0526-00 & 7160-0526-02 Docking
Stations are only compatibile with 3rd, 4th
& 5th generation Getac B300 computers.
Computers can be identified by the p/n
found on the bottom.
3rd generation (B300-H) 52628417xxxx,
4th generation (B300-G4) 52628540xxxx,
5th generation (B300-G5) 52628591xxxx.
1st generation 52628144xxxx &
2nd generation (B300-X) 52628317xxxx
computers are not compatible.
*These instructions are for the docking station only. For instructions on features, set-up
and operation of the B300 computer, please refer to the manuals provided by Getac with
the computer.
**
This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with
each individual product.
IMPORTANT SAFETY INFORMATION for
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding
of automotive electrical procedures and systems, along with proficiency in the installation
and service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the
docking station.
Opening the power/port replication housing will void the product
warranty.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2014 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
INSTALLERS
Revision
Rev.A
Printing Spec: PS-001
Form
INST-626
Page 1 of 8
Advertisement
Table of Contents
Related Manuals for Getac B300 USB 3.0
Summary of Contents for Getac B300 USB 3.0
-
Page 1: Installation Instructions
*These instructions are for the docking station only. For instructions on features, set-up and operation of the B300 computer, please refer to the manuals provided by Getac with the computer. This docking station is designed to be used with a variety of Gamber-Johnson mounting systems. - Page 2 B300 USB 3.0 DOCKING STATION FEATURE IDENTIFICATION Alignment Pin Docking Connector Alignment Pin Interlock Pin Docking Handle Front Retainer Push Button Lock External Speakers External Microphone or Headphones Ethernet Port (4) USB 3.0 Ports Video Connection Alternate DC In (2)Serial Ports...
-
Page 3: Pre-Installation Recommendations
During Installation • DO NOT connect this docking station to the vehicle battery until: 1. ALL other electrical connections are made 2. Mounting of ALL components are complete 3. VERIFICATION that no shorts exist in the entire system • DO NOT install equipment or route wiring or cords in the deployment path of any air bag. -
Page 4: Power Switch
POWER SWITCH This docking station has a power switch with an LED light (see Figure 1): • "INPUT POWER" - The green LED light, built into the power switch, indicates that there is power to the unit. • Standard Installation - In this set-up, the power switch can be turned on and off to regulate power through the unit. -
Page 5: Wiring Instructions
WIRING INSTRUCTIONS IMPORTANT: Make sure that you have read this entire section before you begin wiring! Refer to Figure 2 1. Install docking station into vehicle, making sure that all bolts are tight. 2. Attach BLACK ground wire to the location where the vehicle battery grounds to vehicle chassis. - Page 6 Figure 2 Ground to Vehicle Chassis 14 AWG (black wire) J1128 TYPE GPT Panduit #BSN14-C Butt Splice connects to black lead from dock Panduit #BSN14-C Butt Splice connects to 10" red or blue lead from dock Fuse Vehicle Battery 14 AWG (red wire) J1128 TYPE GPT Connect in-line fuse holder to lead wire using Panduit #BSN14-C Butt Splice connectors...
-
Page 7: Docking The Computer
DOCKING THE COMPUTER 1. Make sure the sliding door (located on the on the back of the computer) has been fully opened, exposing the computer's docking connector. (Figure 4) 2. Set computer in the dock: a. Hook the front of the computer on the front Sliding Door retainer (Figure 5). -
Page 8: Troubleshooting
OPERATING on COMPUTER BATTERY POWER Standard Installation (Power switch is operational) - If the DOCKING STATION power switch is turned off, removing power from the vehicle battery, the Green Switch LED will go out. When the Green Switch LED is off , this indicates that the docking station is being powered by only the computer's battery.