Panasonic TC-P54Z1 Operating Instructions Manual page 6

Accessories/Optional Accessory
Attaching the pedestal to TV (continued)
Attaching the pedestal to TV
Warning
Do not disassemble or modify the pedestal.
Otherwise the TV may fall over and become damaged, and personal injury may result.
Caution
Do not use any other TV and displays.
Otherwise the TV may fall over and become damaged, and personal injury may result.
Do not use the pedestal if it becomes warped or physically damaged.
If you use the pedestal when it is physically damaged, personal injury may result. Contact your nearest Panasonic
Dealer immediately.
During set-up, make sure that all screws are securely tightened.
If sufficient care is not taken to ensure screws are properly tightened during assembly, the pedestal will not be
strong enough to support the TV, and it might fall over and become damaged, and personal injury may result.
Attaching the Speaker to TV
Fix the Mounting bracket securely to the back of the Display unit with
Assembly screws .
Insert the speaker mounting screws temporarily in the screw outermost
holes of the speaker and fix the speaker mounting screws
mounting bracket.
Orient the front side of the Mounting bracket toward the rear side of the
speaker and Display Unit side.
Fix it same as the speaker at the other side.
There will be a gap between the Display Unit and the speaker.
Back of
Display Unit
Mounting bracket
[Top]
Mounting
Assembly
bracket
screws
[Lower right]
Connect Display Unit and speaker with speaker cable.
Fix it in the same way as the speaker on the other side.
Speaker Lower right
(Back of Display Unit)
Speaker
cable
To open the Clamper
Press the part and
Hook
remove the hook.
Note
Tighten the screws firmly.
Insert to the end of the speaker cable terminal firmly.
Loosen the screw shown in fig. above to adjust the gap between the speaker and the Display Unit.
A
Do not hold the speaker to transport the unit.
10
Accessories
Speaker (2)
to the speaker
SP-54Z1U
Mounting bracket
[Top] (2)
Place the temporarily inserted screws
TXFKR04DLUJ
into the counter sunk holes
Front
on the bracket
Back of
Display Unit
Speaker
[Lower right] (1)
TXFKR05DLUJ
Front
Assembly
screws
[Lower left] (1)
TXFKR06DLUJ
Front
Assembly screws
TXFXY01DLUJB
(8)
Speaker cable (2)
TXJ/SPDKUU-1
Connect the terminal
near the ferrite core to
the Display Unit.
(Continued)
■
Wired connection
Connect Display Unit to Tuner Box
Display Unit
Tuner
Box
■
Wireless connection
Connect Wireless Unit (Receiver) to Display Unit
Back
Back
ferrite core
Back
(8)
Assembly screws
Connecting Display Unit, Tuner Box and Wireless Unit
HDMI Cable
Hole for Cable
clamper
Exclusive cable for Wireless Receiver
Insert the metal tab on the
top of the Wireless Unit
(Receiver) into the groove of
the Display Unit.
Insert the tabs on the front of
the Wireless Unit (Receiver)
into the holes at the back of
the Display Unit.
Fix securely with assembly
screws (Total 2 screws).
Accessories
Assembly screws (2)
TXFXY01JSUJB
M4 × 10
HDMI cable
K1HY19YY0006
9.8 ft (3.0 m)
Exclusive cable for Wireless Unit
TXFMM01JSUU
Exclusive cable for Wireless
Receiver
1.6 ft (0.5 m)
Exclusive cable for Wireless
Transmitter
3.3 ft (1.0 m)
Cable clamper (2)
TMME364
Wireless Unit (Receiver)
TU-WHR1U
Wireless Unit (Transmitter)
TU-WHT1U
Caution
Do not disassemble or modify the
Wireless Unit.
Connect the Exclusive cable for
Wireless Receiver which has
ferrite core on Display Unit side.
11