epoc Host2 Quick Start Manual
  1. Manuals
  2. Brands
  3. epoc Manuals
  4. Handhelds
  5. Host2
  6. Quick start manual

epoc Host2 Quick Start Manual

Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

This quick start guide provides first time setup instructions and other useful
instructions for the
instructions, please refer to the
epoc
Host
Components
2
Barcode Scan LED
Barcode scanning active
 
Successful scan/capture (blinking)
Barcode Scanner
Scan Button(s)
Power Button
Epocal, Inc.
2060 Walkley Road
Ottawa, ON K1G 3P5
CANADA
epoc
Host
epoc
®
Host
2

Quick Start Guide

2
(Motorola MC55A0). For complete user
epoc
System Manual.
Emergo Europe
Molenstraat 15
2513 BH, The Hague
The Netherlands
Phone: +31.70.345.8570
Fax: +31.70.346.7299
Charging/Battery LED
Battery fully charged
 
Battery charging (blinking)
 
Charging error (fast blink)
Radio Status LED
(NOT USED!)
Scan Button
(on side)
Touch Screen
(with screen protector)
Keypad
Cradle Blade
51005527-04

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Host2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for epoc Host2

Summary of Contents for epoc Host2

  • Page 1: Quick Start Guide

    Host Quick Start Guide This quick start guide provides first time setup instructions and other useful epoc ® instructions for the Host (Motorola MC55A0). For complete user epoc instructions, please refer to the System Manual. epoc Host Components Charging/Battery LED...

  • Page 2: Numeric Keypad

    Host Numeric Keypad • Power button turns device on and off. Holding the Note: Shaded keys are not active Power button for 5 seconds will reset the device. Scan Toggle Key • Scan key (and Scan Buttons on sides of Host) activates the barcode scanner.

  • Page 3: Step 2: Connect To Your Wi-Fi Network

    For facilities not using an Data Management System, skip steps 2 and 3. Step 2: Connect to your Wi-Fi Network NOTE: Please read Step 2 in its entirety before starting. It may be necessary to contact your facility’s Information Technology department to obtain the proper Wireless connection and security settings.
  • Page 4 Configure the Wi-Fi Network Profile • Tap and hold the screen to bring up the menu; then tap on “Add” . • Enter correct Profile Name and Network Name (ESSID), and then tap “Next” . • Continue entering the correct network security settings on the screens that follow (Screenshots 2-8) by tapping “Next”...
  • Page 5 • If required, tap on the “Fusion” icon and select “Options” to configure the appropriate wireless network options. NOTE: On some networks, it may be required to disable 802.11d in “Regulatory” options. epoc 2. Reset the Host • Perform a warm reset by holding down the power button...
  • Page 6 Step 3: Connect to the Data Manager (EDM) 1. Configure EDM options epoc • Turn on the Host by pressing the power button. • At the login screen, scan or enter the word “administrator” into the User ID and Password fields.

  • Page 7: Installing The Cradle

    Resetting the Host There are two reset functions – warm reset and cold reset. In the rare event that the epoc Host stops responding or is not functioning properly, perform a warm reset. If epoc Host still does not respond, perform a cold reset. Data will not be lost with either procedure, which takes approximately one minute.
  • Page 8 How to install or replace the microSD Card on the Host epoc The SD card slot is located on the back of the Host under the battery compartment. NOTE: It is not necessary to remove the plastic cradle. Battery Release Latch 1.

Table of Contents