Lutron Electronics Maestro User Manual

English
®
Fan Speed P/N 033-214
Control
Quiet Fan Speed Control Multi-Location
System
Canopy Module
CM-FQ1: 120 V~ 60 Hz
1.0 A fan
Wall Control
MA-FQ4M: 120 V~ 60 Hz
4.0 A (up to 4 CM-FQ1)
Accessory Control
MA-AFQ4: 120 V~ 60 Hz
4.0 A
Warning: For use with one to four ceiling paddle fans only. Do not use with an
exhaust fan.
One to four ceiling fans only No exhaust fans
Important Notes
Please read before installing.
1. Caution: To avoid overheating and possible damage to other equipment, do not use to control
receptacles, lighting xtures, transformer-supplied appliances, solid state fan motors, or
exhaust fans. For exhaust fans use Lutron fully variable fan speed controls.
2. Install in accordance with all national and local electrical codes.
3. When no "grounding means" exist within the wallbox then the NEC 2002, Article 404-9 allows
®
a wall control without a grounding connection to be installed as a replacement, as long as a
plastic, noncombustible wallplate is used. For this type of installation, cap or remove the green
ground wire on the wall control and use an appropriate wallplate such as Lutron's Claro
Satin Colors series wallplates.
TM
4. The Maestro fan speed control system consists of a Wall Control, one to four Canopy
®
Modules, and up to two Accessory Controls. All must be installed correctly before attempting
to control the f a ns. Do not attempt to mix Lutron controls with those from other manufacturers,
or mix Lutron controls not labeled for use together.
5. This system is not compatible with fans having a control system built into the motor .
6. Do not paint Wall Control, Canopy Module, or Accessory Control.
7. Maestro Controls are not compatible with standard 3-way/4-way switches.
8. Accessory Controls (MA-AFQ4) cannot be used individually and must be used in conjunction
with a Maestro Wall Control (MA-FQ4M) in a 3-way/4-way application.
9. In any 3-way/4-way circuit use only one Wall Control (MA-FQ4M) with up to 2 Accessory
Controls (MA-AFQ4).
10. Operate between 32 °F (0 °C) and 104 °F (40 °C) room temperature. For indoor use only.
11. Wall Control and Accessory Controls may feel warm to the touch during normal operation.
12. Recommended wallbox depth is 2.5 in (64mm) minimum.
13. Clean controls with a soft damp cloth only. Do not use any chemical cleaners.
14. This system cannot be used to change the direction of the fan. To change the fan direction,
stop the fan, and then change the position of the switch located on the body of the fan.
15. Do not use pull chains to operate fan(s) after installing this system.
16. Each Canop y Module must be installed within a fan canopy enclosure.
17. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Multigang Installations
When installing more than one control in the same wallbox, it may be necessary to remove all inner
side sections prior to wiring (see below). Using pliers, bend side sections up and down until they
break off. Repeat for each side section to be removed. Note: Product does not require derating
when side sections are removed.
Breaking Side
Sections
Inside sections are
removed from each
control
Operation
Tap Button
• Tap once when fan is off -Fan
speed increases to preset level.
• Tap once when fan is on -Fan
Press to increase fan speed
speed slows to off.
Press to decrease fan speed
• Tap twice quickly -Fan speed
increases to full speed.
LEDs
Indicate exact fan speed
LEDs will change with each press
(LEDs not available on Accessory Controls)
or
®
Troubleshooting
Symptom Possible Cause
Fan does not turn ON or no LEDs turn ON. •Front Accessible Service Switch (FASS ) on
control is pulled out to the OFF position.
•Manual switch on f a n is off (ex: pull chain).
•Breaker is OFF or tripped (or fuse blown).
•Fan direction switch is between forward and
reverse.
•Wiring error, call Lutron Technical Support
Center at +1.800.523.9466.
LEDs on Wall Control cycle rapidly and •Unit is not activated properly. Activate system
bottom LED is ON. as described in Step 15.
•Wiring error, call Lutron Technical Support
Center at +1.800.523.9466.
LEDs on Wall Control cycle rapidly and •Communication error. Check wiring; if error
second lowest LED is ON. continues, call Lutron Technical Support
Center at +1.800.523.9466.
Fan vibrates or wobbles. •Fan blades not properly balanced. See fan
manufacturer's instructions.
Fan speeds too slow. • Fan pull chain not set to high.
Wall Control LEDs respond as expected but • Fan pull chain not set to high.
fan does not respond properly. • Wiring error, call Lutron Technical Support
Center at +1.800.523.9466.
Technical Assistance
?
If you have questions concerning the installation or operation of this product, call the
Lutron Technical Support Center. Please provide exact model number when calling.
U.S.A. and Canada (24 hrs/7 days):
Do not remove +1.800.523.9466
outside
Other countries 8am – 8pm ET:
sections.
+1.610.282.3800
México
+1.888.235.2910
Side sections are
Reference Wiring Diagram
removed from both
sides of middle control
Neutral
White
Canopy
Module
Yellow (Fan)
Live Switched Live Black
120 V~
60 Hz
First Fan / Canopy Module
Wall
Control
Brass
Brass
Black
FASS - Front
TM
Accessible
Wallbox
Service Switch
See Step 12 for two- and three-location control wiring.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interf e rence will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For
warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-
paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF
MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF
INSTALLATION, REMOVAL OR REINST ALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM
IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL
DAMAGES. LUTRON'S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE
MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE
OF THE UNIT.
This warranty gives you speci c legal rights, and you may have other rights which vary from state to state. Some states do not allow
the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the
above limitations may not apply to you.
Lutron, Claro, and Maestro are registered trademarks and FASS and Satin Colors are trademarks of Lutron Electronics Co., Inc.
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
© 2010 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Made and printed in the U.S.A. 11/10 P/N 033-214 Rev. A
Lutron Technical Support Center
1.800.523.9466
Canopy Module Installation
Fax +1.610.282.1243
1 Install fan(s).
http://www.lutron.com
• Install fan(s) according to manufacturer's instructions and check for proper operation.
2 Set fan speed.
• Set fan(s) to highest speed using pull chains.
3 Turn OFF power.
• Turn power OFF at circuit breaker (or remove fuse).
Up to 3
Additional
Fans / Canopy
Modules
(up to 4 total)
Note: Up to four ceiling fans can be controlled on one circuit.
Follow steps 4–7 for each fan.
4 Disconnect fan.
• Remove canopy enclosure from ceiling fan mounting bracket.
• Leave any green ground wires connected as directed in fan manufacturer's instructions.
• Disconnect fan from remaining wiring in the ceiling.
Green
Fan Black
Ground
Neutral White
To junction box
Down Rod Bracket
Important Wiring Information
When making wire connections, follow the recommended strip lengths and combinations for the supplied wire
connectors (see wire connector bag).Note: All wire connectors provided are suitable for copper wire only. For
aluminum wire, consult an electrician.
Wire Connectors:
Use to join 1.5 or 2.5 mm² (14 or 12 AWG) ground wire to 0.75 mm²
(18 AWG) Wall Control ground wire, and to join 0.75 mm² (18 AWG)
Canopy Module wire to 2.5, 1.5, 1.0 or 0.75 mm²
(12, 14, 16 or 18 AWG) wire.
5 Connect Canopy Module(s).
• If you have questions about wiring, call the Lutron Technical Support Center at +1.800.523.9466.
To junction box
Switched
Live
Black
Switched
Live to
Canopy
additional
Module
fans
Fan
To fixture
24 hrs / 7 days www.lutron.com
Typical Wire Colors
To junction box
Mounting
bracket
Canopy
enclosure
Flush Mount Bracket
Twist wire
connector
tight.
Wiring the Canopy Module (CM-FQ1):
Use wire connectors to join wires as indicated below
and in the wiring diagram, and to cap any unused
Neutral
wires.
Canopy Connects to:
Module Wire:
White Neutral wires in the junction
box and to fan
White
Black Switched Live wire(s) from
Wall Control and to
Yellow
additional fan(s)
Yellow Fan