Advertisement
Cleaning the Spray Arms
It is necessary
to clean the
spray
arms regularly
for
hard
water chemicals
will clog the spray
armjets
and
bearings.
To remove the
spray arm,
screw off the
nut
to
take out
the
washer on top of
the spray
arm and remove
the arm.
Wash
the arms
in
soapy
and warm
water and
use a
soft brush to clean the
jets. Replace
them after rinsing tbem
thoroughly.
------------------
A
WARNING!
Cleaning the Filters
Filter
assembly
For best
performance
and
results,
the filter assembly
must
be cleaned.
The
filter
efficiently
removes
food
particles
from the
wash
water, allowing
it to be
recirculated
during the
cycle.
For
this
reason,
it
is
a good idea to remove the
larger food
particles
trapped in
the
filter after each
wash cycle
by
rinsing tbe
semicircular
filter
and cup under
running
water.
To
remove
the filter
assembly,
pull on
the
cup
handle
in the upward
direction.
The entire filter
assembly
should be cleaned
at least once a
month.
To
clean
the coarse
filter and
tbe fine
filter,
use a cleaning
brush.
Then,
reassemble
the filter
parts as
shown
in the figures left and reinsert
the entire assembly
in the dishwasher,
positioning
in
its
seat and
pressing
downward.
The dishwasher
must
never be
used without
the filters.
Improper
replacement
of
the filter may
reduce the performance
level of the appliance
and
damage dishes
and
utensils.
. Tever run
the
dishwasher without the
filters
in
place.
(~------------~
1
Cleaning the Door
To clean the
edge
around
the
door,
you should use
only a
soft
warm,
damp
rag.
To
prevent
penetration
of
water into
the
door
lock
and electrical
components,
do
not use a spray
cleaner
of any kind.
Also,
never use abrasive
cleaners
or scouring
pads
on
the
outer
surfaces
because they
will
scratch
the finish. Some papers towels can also
scratch
or
leave
marks
on
the
surface.
A
WARNING!
ever
use
a
spray cleaner to clean the door panel
fgr
it could damage
the
door lock and electrical
components.
It
is not allowed to
use
the abrasive agent or some paper
towel
because of
the
risk of scratching or leaving spots on the
stainless
steel
surface.
Cleaning the Drain Pump
Something
will
occasionally
move
into
the filters
and
the
drain
pump. If this
occurs,
the
drain
pumps
employed
in our dishwashers
are
designed
to
automatically
reverse,
ejecting the
item
back into the
sump
area
or
down the
drain.
If you have to remove an obstacle
from
the
drain pump, before
you
remove the
filters,
you should turn
off
the
power;
Then
remove the
small
black
insert from
the
sump
area.
(You might want to remove
any standing
water
first).
Scoop
out the
item that
is
probably
in
the
sump
area
and
causes the
obstruction.
Remember
to replace the
black
insert
before you put
the filters
back in.
How to Keep Your Dishwasher
in Shape
After Every Wash
When You Go on
Holiday
After every
wash,
turn
offthe water
supply to the appliance
When you go on
holiday,
it is recommended
that you run
a
and
leave the door slightly
ajar
so
that
moisture
and odors
wash cycle with the
dishwasher
empty
and then
remove
are
not
trapped
inside.
the plug
from
the
socket,
turn
off the
water
supply
and
leave the door
of
the appliance
slightly
ajar.
This
will help
the seals last
longer and prevent
odors
from
forming
No Solvents or Abrasive Cleaning
within the
appliance.
Products
Seals
To
clean
the
exterior
and rubber
parts of
the
dishwasher,
do
not
use solvents
or
abrasive
cleaning
products.
Rather,
use
only
a cloth and warm
soapy
water.
To remove
spots
or
stains
from
the surface
of
the
interior,
use a cloth
dampened
with
water and
a
little white
vinegar,
or a
cleaning
product
made specifically
for
dishwashers.
One
of the
factors
that cause
odors
to form
in the
dishwasher
is
food that
remains trapped in
the seal
Periodic
cleaning
with
a
damp
sponge will prevent this
from
occurring.
Advertisement
