Summit DW2432 Installation Manual
Hide thumbs
Also See for DW2432:
- Dimensional drawing (1 page) ,
- Use and care manual (31 pages) ,
- Use & care manual (30 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
Advertisement
Table of Contents
Related Manuals for Summit DW2432
Summary of Contents for Summit DW2432
- Page 1 DISHWASHER Models DW2432 and DW2432SS Installation Manual Felix Storch, Inc. Write Serial Number (on inner door of unit) here: Summit Appliance Division 770 Garrison Avenue _______________________________________ Bronx, New York 10474 www.summitappliance.com...
-
Page 2: Table Of Contents
To prevent accidents which could cause serious injury or death, as well as machine damage, read these instructions before installation and / or use: Contents 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 INSPECT THE DISHWASHER 1.2 HOW TO CONTACT US 2. TOOLS THAT MAY BE NEEDED 3. -
Page 3: Important Safety Instructions
INTRODUCTION WARNING Please read this installation manual and When installing the dishwasher, follow basic precautions, including the particularly the safety instructions following: completely and carefully. They will save you The dishwasher installation must be time and effort and help to ensure optimum performed in accordance with this dishwasher performance. -
Page 4: Inspect The Dishwasher
dishwasher-dedicated, properly grounded 1.1 INSPECT THE DISHWASHER electrical circuit with a fuse or breakers After unpacking the dishwasher and prior to rated for 15 amperes. Electrical supply installation, thoroughly inspect the conductors shall be a minimum of #14 dishwasher for possible freight or cosmetic AWG copper wire rated at 75ºC (167ºF) damage. -
Page 5: Tools That May Be Needed
2. TOOLS THAT MAY BE NEEDED 3. MATERIALS THAT MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line – Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Electrical Supply Cable – Minimum #14AWG, 2 conductors, 1 ground, insulated copper conductors. -
Page 6: Materials Supplied
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts listed to the left. 4.2 MANUAL BAG The dishwasher comes with a manual bag containing: ... -
Page 7: Dishwasher Specifications
5. DISHWASHER SPECIFICATIONS 5.1 TECHNICAL FEATURES Load capacity 12 place settings Permissible water pressure 4.35 – 145 psi (0.3 – 10 bars) Electrical connection 120 V (volts), 12 A (amps), 60 Hz (hertz) Total power 1200 W (watts) Heater power 1000 W (watts) Notice: Because we continually strive to improve our products, we may change our specifications and... -
Page 8: Enclosure Preparation
6. ENCLOSURE PREPARATION Notice: For proper dishwasher operation and appearance, ensure that the enclosure has the minimum dimensions shown in the figure on the previous page. 6.1 ELECTRICAL PREPARATIONS WARNING To avoid electrical shock and/or a fire hazard, make sure electrical work is properly installed. Only qualified electricians should perform electrical work. -
Page 9: Preparation For Installing Mounting Brackets
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS 6.3 ADJUSTING HEIGHT Measure the height of the enclosure. - Page 10 6.3.1 INSTALLING THE FOOT SUPPORTS If the height of the enclosure is 33-7/16” to 34-1/4” (850mm – 870mm), use short supports as shown in the figure. If the height of the enclosure is above 34-1/4” (870mm), use long supports as shown in the figure.
-
Page 11: Installing The Side Trim Strips
Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. Notice: Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top. -
Page 12: Preparing The Water Connection (A)
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. Check with your plumbing supply sources for the proper hose and 90º... -
Page 13: Drain Preparation
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figures A, B, C). Notice: Use any one of these methods. Otherwise, the dishwasher will not operate properly. A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. -
Page 14: Steam Protection Foil
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil (u) to prevent any steam from collecting on the underside of the counter top. 6.7.1 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with a... -
Page 15: Placement Of Dishwasher Into The Opening
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses and electrical wire are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in this figure. -
Page 16: Electrical Connection
7.1.2 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: With braided metal hose With copper tubing 7.1.3 BRAIDED HOSE/COPPER TUBING After connections are made, turn on the water supply to check for leaks. CAUTION ... - Page 17 Install a strain relief (not supplied) into the opening on the kick plate. (Figure A) Pass the electrical supply cable through the strain relief; make sure the strain relief clamps the insulated outer casing of your electrical supply cord and not the wires themselves. Leave 2-15/16”...
-
Page 18: Readjusting Foot Levels
7.3 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet, you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, making sure it is level. - Page 19 Lock the toe kick brackets as shown with the plastic tab in Figure C by pushing the plastic tab on the dishwasher into the teeth of the bracket (C). 3. Now attach the toe kick to the bracket with the two (...
-
Page 20: Installer Checklist
Notice: Notice: The installer is responsible for the If the dishwasher does not operate properly, dishwasher installation. Incorrect installation refer to the self-help hints. is not covered by the warranty. 10. SELF-HELP HINTS: 8. INSTALLER CHECKLIST The power indicator light doesn’t come on: ...
Need help?
Do you have a question about the DW2432 and is the answer not in the manual?
Questions and answers