Fenix Imvico TK51 Series Operation Manual
  1. Manuals
  2. Brands
  3. Fenix Imvico Manuals
  4. Printer
  5. TK51 Series
  6. Operation manual

Fenix Imvico TK51 Series Operation Manual

Thermal printer series
Hide thumbs
Table of Contents

Advertisement

Quick Links

TK51 THERMAL PRINTER SERIES
IF9000 interface
Operation Manual – Version 3
November - 2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TK51 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Fenix Imvico TK51 Series

Summary of Contents for Fenix Imvico TK51 Series

  • Page 1 TK51 THERMAL PRINTER SERIES IF9000 interface Operation Manual – Version 3 November - 2010...
  • Page 2 FENIX IMVICO TK51/IF9000 OPERATION MANUAL Revision list for the TK51 thermal printer series operation manual. Version 3 Date: November 2010 Page Revision type Before change After change Firmware update through the communication port. 7,63 Firmware version transmission command. 2.2.1.a) Earth-GND connection New ticket completed flag DEL EOT n=1 (bit 6).
  • Page 3 FENIX IMVICO TK51/IF9000 OPERATION MANUAL I N D E X IMPORTANT NOTES ON TK51/IF9000 HANDLING ........... 5 0- INTRODUCTION....................7 1- GENERAL SPECIFICATIONS................. 8 1.1-PRINTING SPECIFICATIONS............. 8 1.2- CHARACTER SPECIFICATIONS............8 1.3- ELECTRICAL CHARACTERISTICS........... 9 1.4- PAPER REQUIREMENTS..............9 1.5- ENVIRONMENTAL CONDITIONS............. 10 1.6- INTERNAL BUFFER................
  • Page 4 FENIX IMVICO TK51/IF9000 OPERATION MANUAL 4 – CONTROL COMMANDS................40 4.1- COMMAND NOTATION..............40 4.2- TERMS EXPLANATION..............40 4.3- CONTROL COMMANDS DESCRIPTION.......... 41 APPENDIX A – CHARACTER CODE TABLES............. 68 APPENDIX B – WINDOWS CHARACTER FONT LOADER SOFTWARE..69 APPENDIX C – RECOVERY FROM AUTOCUTTER ERROR......70 APPENDIX D –...

  • Page 5: Safety Precautions

    Over voltage can permanently damage the printer. Under voltage can cause malfunctions. • NEVER wet TK51/IF9000 with water or any other liquid. If any liquid is spilled inside the equipment, unplug the power cable immediately and contact the technical service.

  • Page 6: Cleaning Procedure And Precautions

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL • CLEANING PROCEDURE AND PRECAUTIONS. In order to clean the thermal print head, proceed as indicated by the following steps: 1) Open up the paper cutter. 2) Go down the head lever until clicking. The thermal head is held in the up position .

  • Page 7: Introduction

    The TK51/IF9000 is intended to be integrated into the user’s final system. Its structure allows an easy access both to the interface or the critical parts of the mechanism.

  • Page 8: General Specifications

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 1 – GENERAL SPECIFICATIONS 1.1- PRINTING SPECIFICATIONS a) Printing method: Thermal line printing. b) Print Head: Printing mechanism model type Number of dots CAP9247 (60 mm paper-width model) 448 dots (= 56mm) CAP9347 (80 mm paper-width model)

  • Page 9: Electrical Characteristics

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 1.3- ELECTRICAL CHARACTERISTICS +24V DC ± 2.4V (± 10%) a) Supply voltage: b) Current consumption (at 24V): Number of simultaneously activated dots Maximum 29,4 A 26,7 A Rated Maximum 20,6 A 18,7 A Rated Maximum...

  • Page 10: Environmental Conditions

    Fig. 1.1-Operating Temperature and Humidity Range 1.6- INTERNAL BUFFER The TK51/IF9000 printer has a 512 Kbytes receiving buffer memory. This big receiving buffer allows the printer working in the following way: Firstly, all data is buffered, and afterwards the printing is performed at the maximum possible speed without being affected by the communications time processing.

  • Page 11: Installation

    The TK51 is intended to be used in combination with the SEIKO CAP9000 series printer mechanisms, and so, to result in a finished printer. This printer has been thought to be installed in a bigger case or structure, or another kind of appropriate chassis.

  • Page 12: Tk51 Tension Roller

    (over 0,98N) is needful, since the step motor has the smallest driving torque when it reaches the highest speed (250 mm/s). So, the backlash of paper feeding system can be avoided. The following picture shows the FENIX TK51 tension roller performed. Fig. 2.3- TK51 tension roller. 12/82...

  • Page 13: Tk51/If9000 User Interface Elements

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 2.2- TK51/IF9000 USER INTERFACE ELEMENTS In the TK51/IF9000 user can find the following connectors: • CN1: Power supply connector. • CNx: Serial RS-232, parallel CENTRONICS or USB connector. • CN2: Mechanism connector. • CN9: Led and Buttons connector.

  • Page 14: Power Supply Connector

    Fig. 2.5- Power supply connector as seen from outside the TK51/IF9000. " " " " Use a 3-pin DC jack KPP-3P model or equivalent. The TK51/IF9000 requires one power source: VCC (24V DC) for driving the thermal head and motor. The power supply must meet the following conditions:...

  • Page 15: How To Order

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL A very important point to be aware of is the necessity of keeping the supply wiring the shortest possible. When the printer is supplied with 24VDC, if the input voltage drops a significant quantity the printer could stop working normally. The longest (and thinnest) the wire the higher the impedance and therefore less voltage will have in the input, especially during the high peak currents.

  • Page 16: Programming Mode

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 2.2.1.a) EARTH–GND connection. The IF9000 arranges a terminal to connect the system EARTH to printer GND signal. Between both terminals, there is a filter circuit implemented: EARTH This RC filter avoids a current drift when the EARTH circuit is not good (there is not EARTH connection or is defective, other noisy device in the system is injecting spurious in the main power supply, etc).

  • Page 17: Serial Interface Connection Example

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL Signal direction (from Signal Function the printer side) name Input Data reception line. Output Data transmission line. This signal indicates whether an error occurs. /DTR Output Logic “0” indicates that the printer is connected and ready to receive data, and logic “1”...

  • Page 18: Centronics Parallel Connector

    If the input data is not printed correctly, the transmission conditions between the host device and the TK51/IF9000 do not probably match. If this happens, the character “?” is continuously printed and user must adjust the transmission conditions so that they match.
  • Page 19 FENIX IMVICO TK51/IF9000 OPERATION MANUAL • Switching between online and offline mode The printer does not provide any switch for online/offline mode. The printer is in offline mode in the following cases: a) When powering on or until the printer becomes ready for data transmission b) After it is initialized by the reset signal from the interface c) During the self-test.

  • Page 20: Parallel Interface Pins Assignment For Each Mode

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL Reverse mode (Data transmission from the printer to the host system) The transmission of the printer status to the host system is implemented according to the IEEE1284 standard (NIBBLE MODE). 2.2.3.2-Parallel interface pins assignment for each mode...

  • Page 21: Usb Connector

    2.2.4.1- Assignments of USB connector terminals Signal name Pin nº2 Pin nº1 Vbus D – Pin nº4 Pin nº3 Fig. 2.9- USB connector as seen from outside the TK51/IF9000. User has to use a standard “B” series USB connector. 21/82...

  • Page 22: Thermal Printer Connector

    User side connector type: Housing: LY10-DC40 (JAE) Contact: LY10-C1-1-10000 (JAE) 2.2.6- LEDS AND BUTTONS CONNECTOR Leds and buttons on the TK51/IF9000 can be installed through connector CN7. Just follow next connections (or see in APPENDIX F): User side POWER PAPER END LED...
  • Page 23 The ticket pick-up sensor (CON9) informs to the system if the last ticket printed has been picked-up, so that it can take the suitable action. The status of these sensors can be tested by the DEL EOT command. Next picture shows an example built in the TK51 printer (see in APPENDIX-F).
  • Page 24 FENIX IMVICO TK51/IF9000 OPERATION MANUAL The user can adjust the near-end paper sensor position to determine what quantity of paper (meters) wants to have from the detection. Next pictures show an approximate reference of remainder paper, and how a nib (like a rivet) can help you to locate the forto-sensor.

  • Page 25: Basic Operations

    Fig.3.1- Automatic paper load. 5) Put the paper end in the mechanism inlet. 6) Push the paper in until the TK51 detects it and starts the auto-load sequence. 7) Wait until the auto-load sequence extracts the paper from the printer outlet.

  • Page 26: 2- Manual Paper Load

    " HEXADECIMAL DUMP MODE: If pressed together with PFEED button on start-up, this mode is activated. " PROGRAMMING MODE: in this mode, pressing the button means “NO”. " If pressed when the printer is already started, the TK51/IF9000 feeds and cuts paper, cleaning the nozzle. PROG...

  • Page 27: Leds Indicators

    Besides the normal printing mode, in which all the received data are printed according to the settings or conditions fixed by the commands, the TK51/IF9000 allows three SPECIAL MODES which must be set at the moment of turning on the printer or via commands.
  • Page 28 FENIX IMVICO TK51/IF9000 OPERATION MANUAL Next figure shows an example of SELF-TEST MODE: Rolling Printer pattern status Fig. 3.4- SELF-TEST MODE sample. 28/82...

  • Page 29: Programming Mode

    TK51/IF9000 OPERATION MANUAL 3.4.2- PROGRAMMING MODE The TK51/IF9000 has a PROGRAMMING MODE in order to set up some parameters of the printer, without sending any command. In this mode, the printer makes some questions to the user. These questions must be answered by pressing one of the two push buttons.

  • Page 30: Hexadecimal Dump Mode

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL Next figure shows how the printer asks for the configurable parameters: Answers by means of the push-buttons pressed: " PFEED "PROG " PFEED " PROG " PFEED " PROG " PROG Fig. 3.6- PROGRAMMING MODE sample 3.4.3- HEXADECIMAL DUMP MODE...

  • Page 31: Error Processing

    Fig. 3.7- HEXADECIMAL DUMP MODE sample. 3.5- ERROR PROCESSING The TK51/IF9000 reports the error toward the host by both software and hardware, depending on the communication interface used. In the three communication interface, the status and all its possible errors, can be monitored via software through the DEL EOT command.

  • Page 32: Paper Near- End

    • USB PORT: There is not a special signal to indicate error. It must consult by means of command (DEL EOT). When an error happens, the TK51/IF9000 visually also notifies the error type through the error led located next to the buttons, with a different blinking timing sequence for each of them.

  • Page 33: No Paper / Head-Up Error

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 3.5.1- NO PAPER / HEAD-UP ERROR [Description] The out of paper sensor detects there is not paper on the printing line. When the head lever is turning down the printer will also detect it the same way.

  • Page 34: Thermal Head Voltage (Vp) Error

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 3.5.5- THERMAL HEAD VOLTAGE (Vp) ERROR [Description] The power supply voltage is out of range (24VDC + 10%). [Recover action] This is a recoverable error. Unplug the power supply from the printer and check if the output voltage of the power supply is within the specified range.

  • Page 35: Serial Port Error Detection Flow Chart

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 3.5.9- SERIAL PORT ERROR DETECTION FLOW CHART BEGINNING SEND COMMAND nDTR = 0 DEL EOT READS THE PRINTER STATUS AND IDENTIFIES THE ERROR nRTS = 0 SENDS 1 BYTE END OF TRANSMISSION Fig.3.9- Serial port error detection flow chart.

  • Page 36: Parallel Port Error Detection Flow Chart

    Fig.3.10- Phase transitions of the nibble mode. NOTES The host system can request the negotiation phase at any time, but the TK51/IF9000 will only return a status byte if the host system has send the DEL EOT command previously. The circles represent the IEEE1284 phases.

  • Page 37: Optical Mark

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 3.6- OPTICAL MARK The TK51/IF9000 has a specific sensor for optical (black) mark detection. To make use of this feature, the optical mark sensor must be programmed by buttons (See point 3.4.2- PROGRAMMING MODE). The black mark must be placed in the back right side (opposed to printing side), and must satisfy the minimum dimensions showed in the follow picture.
  • Page 38 FENIX IMVICO TK51/IF9000 OPERATION MANUAL 3.6.1- EXAMPLE USING PAPER WITH BLACK MARK Some points must be taken in account when using paper with black mark. There are three commands for handling marked paper: • GS ( F... " " " " Set offset values. This command allows setting the distances between the optical mark and the ticket cutting position (cut offset) and the start ticket printing position (print offset).
  • Page 39 FENIX IMVICO TK51/IF9000 OPERATION MANUAL Next pictures illustrate a sequence example handling the marked paper. Previously, GS ( F... command has been sent, setting the print and cut offsets. TICKET n+1 TICKET n Paper feed Fixed positions into the printer .- Ticket n is in the start...

  • Page 40: Control Commands

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 4 – CONTROL COMMANDS 4.1- COMMAND NOTATION [Name] The name of the command. [Format] The code sequence. [ ]k indicates the contents of [ ] should be repeated k times. [Range] Gives the allowable ranges for the arguments.

  • Page 41: Control Commands Description

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL 4.3- CONTROL COMMANDS DESCRIPTION [Name] Print and line feed [Format] ASCII Decimal [Description] Prints the data in the print buffer and feeds one line, based on the current line spacing. [Note] This command sets the print position to the beginning of the line.
  • Page 42 FENIX IMVICO TK51/IF9000 OPERATION MANUAL n = <01>H: Printer status OFF/ON Function Not used. Fixed to OFF Not used. Fixed to ON Not used. Fixed to OFF Online Offline Not used. Fixed to ON Does not wait for online error recovery...
  • Page 43 FENIX IMVICO TK51/IF9000 OPERATION MANUAL n = <04>H: Continuous paper sensor status OFF/ON Function Not used. Fixed to OFF Not used. Fixed to ON Undefined Paper near-end sensor: Paper present Paper near-end sensor: Paper not present Not used. Fixed to ON...
  • Page 44 FENIX IMVICO TK51/IF9000 OPERATION MANUAL ESC ! n [Name] Select print mode(s) [Format] ASCII ESC ! Decimal <00>H ≤ n ≤ <FF>H [Range] [Description] Selects print mode(s) using n as follows: OFF/ON Function Character font A (12 x 24). Character font B (8 x 16).
  • Page 45 FENIX IMVICO TK51/IF9000 OPERATION MANUAL ESC 3 n [Name] Set line spacing [Format] ASCII Decimal <00>H ≤ n ≤ <FF>H [Range] [Description] Sets the line spacing to [n x 0.125 mm]. [Default] n = <1E>H [Reference] ESC 2 ESC @...
  • Page 46 FENIX IMVICO TK51/IF9000 OPERATION MANUAL ESC M n [Name] Select character font [Format] ASCII ESC M Decimal [Range] n = <00>H, <01>H [Description] Selects the character font. Function <00>H Character Font A (12 x 24) selected <01>H Character Font B (8 x 16) selected [Notes] •...
  • Page 47 [Description] Cuts the paper fully in the current position. [Notes] • If this command is sent without cutter connection or the cut is not whole make, TK51/IF9000 enter cutter error status. • The interval between each cutting operation must be 2 seconds or more. •...
  • Page 48 [Notes] • If this command is sent without cutter connection or the cut is not whole make, TK51/IF9000 enter cutter error status. • The interval between each cutting operation must be two seconds or more. • This command performs the partial cut even when the black mark is enabled, but any action relative to black mark is performed.
  • Page 49 FENIX IMVICO TK51/IF9000 OPERATION MANUAL ESC G n [Name] Turn on/off double-strike mode [Format] ASCII ESC G Decimal 0 ≤ n ≤ 255 [Range] [Description] Turns double-strike mode on or off. When the LSB of n is 0, double-strike (emphasized) mode is turned off.
  • Page 50 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS FF [Name] Feed marked paper to print starting position [Format] ASCII Decimal [Description] Feeds paper until finding the black mark. Then moves the ticket, forward or backward, placing it at the printing position. [Notes] •...
  • Page 51 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS ( A pL pH n m [Name] Execute test print [Format] ASCII Decimal [Range] (pL + (pH x 256)) = 2 (where pL = <02>H, pH = <00>H) <30>H ≤ n ≤ <32>H <31>H ≤ m ≤ <33>H [Description] •...
  • Page 52 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS ( F pL pH a m nL nH [Name] Set print/cut offsets related to black mark F pL pH a m nL nH [Format] ASCII GS ( 1D 28 46 04 00 a m nL nH [Range] pL = <04>H, pH = <00>H (fixed)
  • Page 53 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS E n [Name] Select the printing speed. [Format] ASCII 45 n [Range] n = <00>H, <10>H, <20>H, <30>H [Description] Selects the printing speed. Printing speed <00>H 250 mm/s (max) <10>H 200 mm/s (max) <20>H 150 mm/s (max) <30>H...
  • Page 54 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS L nL nH [Name] Set left margin [Format] ASCII Decimal <00>H ≤ nL ≤ <FF>H [Range] <00>H ≤ nH ≤ <FF>H [Description] • Sets the left margin using nL and nH. • The left margin is set to [(nL + nH x 256) x 0.125 mm].
  • Page 55 • After cutting the ticket, the printer always feeds the paper back to the printing position. • If this command is sent without cutter connection or the cut is not whole make, TK51/IF9000 enter cutter error status. [Notes for •...
  • Page 56 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS f n [Name] Select font for Human Readable Interpretation (HRI) characters [Format] ASCII Decimal [Range] n = <00>H or <01>H [Description] Selects a font for the HRI characters used when printing a bar code.
  • Page 57 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS k m n d1...dn [Name] Print bar code [Format] ASCII d1...dn d1...dn d1...dn Decimal [Range] m = <43>H , m = <45>H, m = <46>H or m = <49>H (n and d depend on the bar code system used).
  • Page 58 FENIX IMVICO TK51/IF9000 OPERATION MANUAL Specific Transmit data character ASCII Decimal SHIFT 7B, 53 123, 83 CODE A 7B, 41 123, 65 CODE B 7B, 42 123, 66 CODE C 7B, 43 123,67 FNC1 7B, 31 123, 49 FNC2 7B,32...
  • Page 59 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS v 0 m xL xH yL yH d1 ... dk [Name] Print raster bit image xL xH yL yH d1...dk [Format] ASCII xL xH yL yH d1...dk xL xH yL yH d1...dk Decimal <00>H ≤ m ≤ <03>H [Range] <00>H ≤...
  • Page 60 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS w n [Name] Set bar code width [Format] ASCII Decimal <02>H ≤ n ≤ <06>H [Range] [Description] Sets the horizontal size of the bar code. n specifies the bar code width as follows: Module Width (mm)
  • Page 61 FENIX IMVICO TK51/IF9000 OPERATION MANUAL FS p n m [Name] Print NV bit image [Format] ASCII Decimal [Range] n = <01>H <30>H ≤ m ≤ <33>H [Description]Prints a NV bit image n using the mode specified by m. Vertical Horizontal...
  • Page 62 FENIX IMVICO TK51/IF9000 OPERATION MANUAL FS q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk] [Name] Define NV bit image [Format] ASCII FS [xL xH yL yH d1...dk]1...[ xL xH yL yH d1...dk] [xL xH yL yH d1...dk]1...[ xL xH yL yH d1...dk] [xL xH yL yH d1...dk]1...[ xL xH yL yH d1...dk]...
  • Page 63 Thus, the system could check whether the current version is less than the new provided (contact with FENIX IMVICO or distributor if necessary). • Returns one byte indicating numerically the current firmware version.
  • Page 64 FENIX IMVICO TK51/IF9000 OPERATION MANUAL ESC V n [Name] Character rotation [Format] ASCII 56 n 86 n Decimal <30>H ≤ n ≤ <32>H [Range] [Description] Rotes the characters using the mode specified by n. Function <30>H Normal <31>H Right 90º rotated <32>H Left 90º...
  • Page 65 FENIX IMVICO TK51/IF9000 OPERATION MANUAL ESC { n [Name] Inverse printing mode [Format] ASCII 123 n Decimal [Range] n = <30>H , n = <31>H [Description] Turns inverse printing mode on/off. Function <30>H Inverse printing mode off <31>H Inverse printing mode on...
  • Page 66 FENIX IMVICO TK51/IF9000 OPERATION MANUAL GS a n [Name] Automatic status report [Format] ASCII Decimal [Range] n = <30>H , n = <31>H [Description] Enable/disable automatic status report. Function <30>H Disabled automatic status report <31>H Enabled automatic status report • When enabling the automatic status report, the printer remains in this state indefinitely, until it becomes disabling, or until switch the power off.
  • Page 67 Taking advantage of high features in drawing and image handle software like Word, Paint, PhotoShop, etc. the user can load 1 logo, selecting in “Device operation” (TK51 Windows driver) the correct option. We suggest adjusting the logo selecting “Driver mode” option until get the size, the layout and the arrangement desired.

  • Page 68: Appendix A - Character Code Table

    TK51/IF9000 OPERATION MANUAL ______________________________________________________ APPENDIX A – CHARACTER CODE TABLE ______________________________________________________ The TK51/IF9000 has built in the following full character code table, in both font A(12x24) and font B(8x16) formats: PAGE 0: PC437 USA, Standard Europe (International Character Set: USA). 68/82...

  • Page 69: Appendix B - Windows Character Font Loader Software

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL ___________________________________________________________________ APPENDIX B – WINDOWS CHARACTER FONT LOADER SOFTWARE ___________________________________________________________________ The font loader program has the following features: Allows the user to load directly into the printer's non-volatile memory any TrueType font installed under Windows Operating System in order to be used by the printer in command mode (with no need of the driver).

  • Page 70: Appendix C - Recovery From Autocutter Error

    FENIX IMVICO TK51/IF9000 OPERATION MANUAL ____________________________________________________________________ APPENDIX C – RECOVERY FROM AUTOCUTTER ERROR ____________________________________________________________________ • If an object, such as a push pin or paper clip, drops in the autocutter and causes the autocutter to lock up, the printer will enter error state.

  • Page 72: Appendix D - External Appearance

    __________________________________________________________________ APPENDIX D – EXTERNAL APPEARANCE ____________________________________________________________________ • IF9000 INTERFACE Maximum height: 20 mm...
  • Page 73 FENIX IMVICO TK51 OPERATION MANUAL • TK51 PRINTER 73/82...

  • Page 74: Appendix E - Specifications

    APPENDIX E – SPECIFICATIONS Model TK51-60 TK51-80 TK51-112 Printing method Thermal dot line Printing mechanism SEIKO SEIKO SEIKO CAP9247A CAP9347A CAP9447A Data interface IEEE 1284 (Nibble mode) parallel, RS232 Serial or Dot composition/line Resolution 8 dots/mm Printing speed (mm/sec) Paper width (mm) Paper roll diameter 150mm MAX.

  • Page 75: Appendix F - How To Order- Accesories

    Standard 110 mm diameter paper roll for 60mm (xx=60), 80mm (xx=80), TxxX110X25 82mm (xx=82) or 112mm (xx=12) Standard 150 mm diameter paper roll for 60mm (xx=60), 80mm (xx=80), TxxX150X25 82mm (xx=82) or 112mm (xx=12) Fotocélula IF9000 paper near-end photo-sensor IFPULSA500 TK51 led and push buttons Fotocélula IFPULSA500 FAPOS-1 75/76...

  • Page 76: Appendix G - Code128 Bar Code

    FENIX IMVICO TK51 OPERATION MANUAL __________________________________________________________________ APPENDIX G – CODE128 BAR CODE ____________________________________________________________________ In Code128 bar code system, it is possible to represent 128 ASCII characters and 2- digit numerals using one bar code character that is defined by combining one the 103 bar code characters and 3 code sets.
  • Page 77 FENIX IMVICO TK51 OPERATION MANUAL G.2 Printable characters in CODE SET A Transmit Data Transmit Data Transmit Data Character Character Character Decimal Decimal Decimal FNC1 7B,31 123,49 FNC2 7B,32 123,50 FNC3 7B,33 123,51 FNC4 7B,34 123,52 < SHIFT 7B,53 123,83...
  • Page 78 FENIX IMVICO TK51 OPERATION MANUAL G.3 Printable characters in CODE SET B Transmit Data Transmit Data Transmit Data Character Character Character Decimal Decimal Decimal “ & ´ 7B,7B 123,123 FNC1 7B,31 123,49 FNC2 7B,32 123,50 FNC3 7B,33 123,51 FNC4 7B,34...
  • Page 79 FENIX IMVICO TK51 OPERATION MANUAL G.4 Printable characters in CODE SET C Transmit Data Transmit Data Transmit Data Character Character Character Decimal Decimal Decimal FNC1 7B,31 123,49 CODEA 7B,41 123,65 CODEB 7B,42 123,66 79/76...

  • Page 80: Appendix H - Testing Software

    FENIX IMVICO TK51 OPERATION MANUAL ___________________________________________________________________ APPENDIX H – TESTING SOFTWARE ____________________________________________________________________ The TK15/TS1600 printer is delivered together with a Windows-based, testing program. This program is an easy way to explore the TK15/TS1600’s main features. To install the program, run the “SETUP.EXE” file and follow the instructions on the screen.

  • Page 81: Printer Configuration

    FENIX IMVICO TK51 OPERATION MANUAL There are three main sections which are Printer Configuration, Sample Ticket and Printer Status. PRINTER CONFIGURATION In this section we can set all the configuration parameters related to the printer settings as communication setup and paper width.
  • Page 82 FENIX IMVICO TK51 OPERATION MANUAL c/ Pacífico, 53-55 – 08027 BARCELONA, SPAIN Phone Num: +34 – 93 353 92 22 Fax Num: +34 – 93 353 97 21 E-mail: bcn@feniximvico.com http://www.feniximvico.com 82/76...

This manual is also suitable for:

F9000Tk51-60Tk51-80Tk51-112

Table of Contents