Panasonic TC-P58V10 Operating Instructions Manual page 23

Network Setting
This is a setting for connecting to a broadband environment.
Display menu
Select "Setup"
Menu
Picture
Audio
Timer
Lock
VIERA Link
SD card
Closed caption
Setup
Select "Network setting"
Setup
VIERA Link settings
Network setting
VIERA CAST setting
Network Cameras list
ECO/energy saving
Advanced setup
About
Reset to defaults
■
Press to exit from
a menu screen
Select the item and adjust
Network setting
■
Connection test
Press to return
IP setting mode
IP address
to the previous
Subnet mask
screen
Default gateway
DNS setting mode
Primary DNS
Secondary DNS
Network setting
LAN speed setting
LAN speed
Software update
MAC address
44
Connection
test
select
set or next
IP setting
• IP setting
• IP address
• Subnet mask
• Default
select
2/2
DNS setting
• DNS setting
• Primary DNS
• Secondary
select
1/2
Succeeded
adjust
Automatic
192.168.0.5
255.255.255.0
192.168.0.254
Automatic OK Connection
192.168.0.20
speed
192.168.0.21
setting
2/2
Automatic
• LAN speed
10BASE half duplex
12-34-56-78-80-ab
• LAN speed
Software
update
Check that the network settings are as shown below, and then start "Connection test".
Select "Connection test" and press OK.
*Press OK again to cancel the test.
(It takes a while to cancel the test.)
Network setting
Connection test
IP setting mode
IP address
Subnet mask
Default gateway
Select "IP setting mode" and set to "Automatic".
(When IP automatic acquisition in DHCP can be used)
Network setting
Connection test
IP setting mode
mode
IP address
Subnet mask
Default gateway
The acquired address is displayed.
gateway
Each IP address is acquired automatically.
Select "DNS setting mode" and set to "Automatic".
(When DNS automatic acquisition in DHCP can be used)
Network setting
Connection test
Default gateway 192.168.0.254
IP setting mode
DNS setting mode
Primary DNS
Secondary DNS
mode
The acquired address is displayed.
Each IP address is acquired automatically.
DNS
If you are using a broadband router, IP automatic
acquisition in DHCP can be used under normal
circumstances. If you are not sure, check with the
person who installed the equipment, or check the
instructions for each device.
Select "LAN speed setting" (Default is "Automatic")
Network setting
LAN speed setting
LAN speed 10BASE half duplex
Software update
MAC address 12-34-56-78-80-ab
setting
Select "Software update"
Network setting
LAN speed setting
LAN speed 10BASE half duplex
Software update
MAC address 12-34-56-78-80-ab
The network settings become effective when you close the menu and run "Connection test".
Succeeded: "Connection test" succeeded
Only home network:
Home network is available.
Failed: Check the broadband environment connection
select
and settings and the network settings, and then
1/2
Succeeded perform the test again.
Manual
Test in progress
ok
192.168.0.5
---: Test not yet performed
255.255.255.0
192.168.0.254
■
Manual setting
Select "IP setting mode" and set to "Manual"
Select the item and press OK
1/2
select Check the specifications of the broadband router and
Succeeded
enter each IP address.
Automatic
192.168.0.5
ok
255.255.255.0
Subnet mask
192.168.0.254
■
Manual setting
Select "DNS setting mode" and set to "Manual"
Select the item and press OK
select
1/2
Enter each IP address as was specified by the
Succeeded
provider.
Automatic
Automatic OK
ok
192.168.0.20
192.168.0.21
Primary DNS
Normally, select "Automatic".
If "Connection test" failed, set the "LAN speed setting"
select
2/2
to "manual" and then select "10BASE half duplex",
Automatic
"10BASE duplex", "100BASE half duplex" or "100 BASE
adjust
duplex".
Cannot be selected when the "LAN speed setting" is
"Automatic".
Changing the settings may make it impossible to
connect some types of equipment.
Press OK to start the software update screen.
select Follow directions of the screen.
2/2
Automatic OK
* Set "Clock" first. (p. 18)
ok
10I 0 . 0 . OK 0 . 0
change
or
channel
ok
10I 0 . 0 . 0 . 0
select
or
ok
45