Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KTI Networks KF 310
Summary of Contents for KTI Networks KF 310
- Page 1 32-bit PCI-Bus 10/100Mbps ACPI Fast Ethernet Card User’s Guide...
-
Page 2: Fcc Statement
FCC Statement This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant... -
Page 3: System Requirements
1. Introduction Congratulations on the purchasing of your new 10/100 NWay Fast Ethernet PCI adapter. This document describes the Installation of network adapter. This adapter supports 10BASE-T/100BASE-TX Fast Ethernet and complies with the electrical and protocol requirements of the PCI Local Bus Specification, revision 2.2. -
Page 4: Installation
2. Installation This section describes how to install the adapter. For connecting to the network, you must have the following: 1. Network adapter card installed to your computer. 2. Cabling (compatible with network topology) 3. Connect the Wake-On-LAN cable to the motherboard (If the WOL function is supported on the adapter) 4. -
Page 5: Install The Adapter
2.2 Install the Adapter 1. Turn off the computer. 2. Remove the computer’s cover, in accordance with its manual. 3. Insert the contact edge of the adapter card into the connector of any available PCI Bus master expansion slot. Press the card firmly into the connector to PCI slot. Please make sure that the card’s contacts are fully seated in the PCI slot. - Page 6 2.3 Connect Fast Ethernet Category 5 UTP cable is required for Fast Ethernet operation. The maximum cable run between the adapter and the supporting hub is 300ft (100m). Make the network connection by plugging one end of the cable into the RJ-45 receptacle of the adapter, and the other end into one port in the hub.
-
Page 7: Drivers And Utilities Diskette
2.5 Drivers and Utilities Diskette The [Divers and Utilities] diskette contains all the popular operating system drivers. Ÿ Novell NetWare(client /server) Ÿ Windows NT 3.5, NT4.0/2000/XP Ÿ Windows 95/98/ME Ÿ Microsoft Client (NDIS 2.0 DOS/OS2) Ÿ Windows For Workgroup 3.11 Ÿ... - Page 8 After choosing the <Run Diagnostics on Board> item, the screen will display like, Node ID..: 00 e0 7d c0 00 01 Network Speed..: 100Mbps I/O Base ..: E000H Interrupt ..: 11 Full-Duplex ...: Disabled Pass Count Fail Count A. I/O Register B.
- Page 9 To wake up Target Machine with Magic Packet Step1: Target Machine: Target Machine is necessary to use the WOL cable link the Wake On LAN connector on adapter with your motherboard. Check BIOS <POWER MANGEMENT SETUP> ACPI, Wake On LAN function must be enable.
-
Page 10: Quick Installation Guide
Quick Installation Guide Please take the following steps for driver installation. Microsoft Windows 95/Windows 98/Windows ME 1. Turn off the computer. 2. Insert the adapter into the available PCI slot. 3. Restart the computer. 4. After Microsoft Windows reboot, the PCI Ethernet Controller will be found. - Page 11 Microsoft Windows 2000 1. Turn off the computer. 2. Insert the adapter into the available PCI slot. 3. Restart the computer. 4. After Microsoft Windows reboot, the 10/100Mbps Fast Ethernet Adapter will be found and the system will assign the default network driver to the adapter. 5.
- Page 12 Novell Netware System Please execute the following commands: For Netware Client RTSODI IPXODI NETX or VLM LOGIN <USERNAME> For Netware Server LOAD RTSSRV BIND IPX TO RTSSRV The help file in the diskette will describe the detail driver installation information for all popular operating systems. F-310...
Need help?
Do you have a question about the KF 310 and is the answer not in the manual?
Questions and answers