Subscribe to Our Youtube Channel
Related Manuals for Skope ELITE 3D
Summary of Contents for Skope ELITE 3D
- Page 1 SKOPE Airelec ELITE 3D Convection Panel Heaters Vertical, Horizontal and Plinth models...
- Page 2 SKOPE Airelec heating SKOPE Airelec Elite 3D convection panel heaters are available as vertical, horizontal and plinth models, providing you with the opportunity to choose a model that will optimise the valuable wall space available in your room. These designs have passed rigorous testing and quality assurance controls with both style and safety in mind.
-
Page 3: Safety Information
For your own safety and that of others, ensure this is done. • If the supply cord becomes damaged, it must be replaced by a SKOPE authorised service agent, or similarly qualified person, in order to avoid a hazard. • For service, contact your nearest authorised service agent. -
Page 4: Safety Cut-Out
Safety Cutout Your SKOPE Airelec convection heater is fitted with an auto-reset thermal cutout. This safety device will automatically switch off the elements should the heater reach an abnormal temperature. Should this occur: switch off the heater immediately, and disconnect from the power supply. -
Page 5: Control Settings
This setting is useful during extended periods of absence, or for unoccupied rooms. The thermostat knob does not need to be adjusted for Freeze Guard to operate. Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters... -
Page 6: Installation
NOTE: For pilot wire connection details, see separate ‘Ecobox2 Pilot Wire Transmitter’ Operating Instructions (P/No: MAN9762). Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters... -
Page 7: Mounting Instructions
Lift the heater up and away from the wall. Wall mounting bracket removed from heater Wall mounting bracket Lever OUT Bayonet fitting Push IN Heater body Heater body Figure 2: Wall Mounting Bracket Fitting Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters... - Page 8 755mm 200mm 90mm 235mm SKOPE Industries Limited reserve the right to alter specifications without notice. Table 2: Installation Dimensions Important! When operated for the first time, the heater may emit a small amount of smoke. This is normal, and should clear within a few minutes.
-
Page 9: Wall Mounting Bracket
Top fixing holes Bayonet fittings Heater outline Mounting bracket Side fixing hole (ETP10 models only) Bottom clips Bottom fixing holes 150 mm IMPORTANT Minimum Floor level Figure 3: Wall Mounting Bracket Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters... - Page 10 Fasten a screw (e.g. No.6 x 1/4” self tapper) into the hole. The screw should be large enough to impede movement of the knob. The thermostat knob should now be locked at the required setting. Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters...
-
Page 11: Specifications
Neutral = Blue Pilot wire = Black * * The black pilot wire MUST NOT be connected to Earth. See page 6 for connection details. Double Insulated Table 4: Electrical Specifications Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters... -
Page 12: Contact Addresses
Freefax: 1800 121 533 Email: enquiry@skope.com.au Website: www.skope.com.au Servicing If your heater is in need of servicing, contact your nearest authorised service agent (see separate enclosed list of service agents). Elite 3D ELITV, ELITH and ELITPL SKOPE Airelec Convection Panel Heaters...
Need help?
Do you have a question about the ELITE 3D and is the answer not in the manual?
Questions and answers