INTRODUCTION OVERVIEW This combo receiver is designed for using both free-to-air and encrypted channel reception. Enjoy the rich choice of more than 20,000 different channels, broadcasting a large range of culture, sports, cinema, news, events, etc. This receiver is a technical masterpiece, assembled with the highest qualified electronic parts.
EASY INSTALLATION GUIDE Part 1 Using the Preinstalled Satellite & Channel list This receiver is preinstalled with Satellites and default Channels and is fully configured. No settings need to be changed. After turning ON the receiver, select a language. Go to system setting and Factory Reset Menu. If you select Restore default channels, You can use preinstalled default channel list.
Page 4
How to Install a New Satellite(Fixed Non-Motorized System) Press the MENU button on the remote and press the OK button on Installation setup. Press OK on satellite to display a Satellite List. To add a satellite, press the YELLOW( ) button on the remote.
Page 5
Press the MENU button on the remote. Go to Factory Reset and insert PIN Code(default 0000) Then go to Restore default channels, press OK button on the remote. Select YES It will retrieve default channels. Active Transponders For Technomate Motorized Systems Satellite Name Degree Frequency...
Safety Instructions 1. Be sure to read this User's Manual before starting the operation of the receiver. 2. Do not touch a power cord with wet hands as it may cause electric shock. 3. Never open the cover. It is very dangerous to touch the inside of the unit due to the possibility of an electric shock.
CHECK POINTS BEFORE USE ACCESSORIES If any accessories listed above are missing, contact the sales representative where you purchased this unit. SATELLITE DISH You dish should be properly installed and azimuth and elevation must be precisely set up. This unit is working with DiSEqC 1.2 on a compatible antenna positioner. Ask your dealer for more information.
CONTROLS/FUNCTIONS FRONT/REAR PANEL Watching TV status (Live mode) OSD operating status (OSD mode) Turns the receiver on/off. 1. Power To enter or exit the Main Menu. 2. Menu To change a previous menu or live mode. Current channel displays in VFD display screen. 3.
Page 9
REMOTE CONTROL 1. POWER : To turn the receiver On/Off. 2. MUTE : To turn the Sound On/Off. 3.TV/SAT : To switch the TV output source between the satellite input and the UHF/VHF antenna input. 4. ZOOM : To zoom In/Out. 5.
FRONT DISPLAY Power On/Off mode It is displayed when a Satellite channel is viewing It is displayed when a Terrestrial channel is viewing It is displayed when a USB device is connected. It is displayed when a channel is recording It is displayed when the channel is HD Displays the video output’s resolution Displays the video output’s resolution...
EQUIPMENT CONNECTION CONNECTION WITH ANTENNA / TV SET / A/V SYSTEM 1. Connect the TV antenna to TV ANT IN. 2. Connect the Video and Audio of TV to the Video and Audio. Connect Red and White connector to Audio R and Audio L and Yellow into video port respectively.
OPERATION GETTING STARTED Turn your receiver power on and proceed with system setup as follows: Menu Language Setting 1. Turn on your TV and receiver. 2. The language selection menu will be displayed, select a language and press the OK button on. Installation Setup 1.
Page 13
Motorized Setup 1. Press the MENU button on the remote to display the main menu. ▲/▼ 2. Use ◀/▶ and buttons on the remote to move in the menu. 3. Select Motorized Setup, the Motorized Setup menu will appear. 4. Select each menu you want to edit /change - Satellite : Select any satellite by pressing ◀/▶...
Page 14
USALS System Setup 1. Select USALS on DiSEqC Motor, the USALS menu will appear. - Satellite : Select any satellite by pressing ◀/▶ buttons. - Transponder : Displays the current TP value of the selected satellite. - DiSEqC Motor : Select DiSEqC Motor USALS. - Position setting : set the current degree of the selected satellite by press OK button •...
Page 15
Auto Navigation All the available channels/satellites can be searched in this menu. Select the satellite and save before Auto Search. 1. Press the MENU button on the remote to display the main menu. ▲/▼ 2. Use ◀/▶ and button on the remote to move in the menu.
Page 16
Advanced Search To edit and search channels on newly launched satellites or not preprogrammed satellites in the list. 1. Press the MENU button to display the main menu. ▲/▼ 2. Use ◀/▶ and buttons to move in the menu. 3. Select Advanced Search, the Advanced Search menu will appear.
Page 17
- Channel : Select Channel Number for scanning. - Transponder : Display Frequency of selected Channel. - Bandwidth : Display Bandwidth of selected Channel. - Scan Mode : Select search type (Free+CA, Free Only, CA Only) - Network Scan : Select Network Search On/Off. - Radio CH : Search TV channels only or All(TV+Radio) channels.
Page 18
■ AUDIO You can press AUDIO button to select audio language provided by service provider. ■ TEXT The Teletext service is a text data service sometimes available from the Service Provider. ■ SAT Press the SAT button to select a satellite in the Satellite List. ■...
■ WIDE Press the WIDE button to change the TV’s Aspect Ratio directly. 4:3 : Pan-Scan or Letter Box or Full-Frame 16:9 : Center-Cut-Off or Pillar Box or Full-Frame ■ COLOR Adjustment Press the COLOR button on the remote to select Color Adjustment menu.
Page 20
TIME SETUP This submenu arrows you to set your local time - Time : Display current date and time. - GMT-Time: Sat : Display GMT date and time using satellite stream information. - GMT-Time: Terrestrial : Display GMT date and time using terrestrial stream information.
Page 21
- Lock Level : If you select INSTALL, you will be asked to enter PIN when you go to installation/edit channels/EDIT button. If you select MENU, you will be asked to enter PIN when you go to menu. - Age Limit : Prevents children or unauthorized people from watching the specific programs.
IP Settings If the Network supports DHCP, IP settings can be allocated automatically, If the Network does not support DHCP, the Addresses must enter manually.(Static IP). - DHCP Usage : On/Off to receive IP settings automatically. - IP Address : Here enter the IP address. - Subnet Mask : Here enter Subnet Mask Number from your Network.
Page 23
2. Select Edit Favorites, Favorite Edit menu will appear. - EDIT( ) : If you want to edit the favorite name, press Red button on the remote. At favorite name menu, press OK button for virtual keyboard. - NEXT LIST( ) : Press Green button to toggle Favorite 1~8 / Favorite 9~16 List - CH CHANGE(...
Page 24
Front Display Settings This sub-menu allows you to control front display. 1. Press the MENU button on the remote to display the main menu. 2. Select Front display settings, Front display settings menu will appear. - Text Moving : Turn the text moving On/Off. - Channel Number : Turn the channel number On/Off - LED : Turn the blue light On/Off - VFD : Control VFD Display light 0 / 1 / 2 / 3...
CAM(COMMON INTERFACE MODULE) Only CAM Initializing To watch scrambled channels, you will need a Conditional Access Module(CAM) and Smart card which is specific to that CAM from the service provider (broadcaster). *Note : Without a CAM and a smart card, you can watch only Free-to-Air programs.
System Information You can check the current information about your receiver, such as the receiver Model name, Hardware version, Software version, hardware version, Last update, etc. *Note : This information is necessary when you want to download a new software or you need to repair the receiver.
MP3 Menu ▲/▼ 1. Use , OK button to select the MP3 file that you want to listen 2. Use button to select Icon in the MP3 Player box. ◀ ▶ 3. Press the OK button to select a file. ◀◀...
Page 28
- DIR MODE/FILE MODE : You can view Dir/File view mode using this button. - TIME SORT/NAME SORT : You can sort files with Time or Name using this button. - LOOP PLAY/NORMAL PLAY : Use this button to view all file list one by one.
Page 29
▶ RWD(Rewind) When playing the file, press the RWD button to rewind the program (adjust the playing speed). - Choose from : x2, x4 and x8 ▶ SLOW(1/2x, 1/4x) When playing the file, press the SLOW button to slow the speed of the playback. (adjust the playing speed) ▶...
Page 30
Timer Recording This function is available when HDD or USB device is connected. You can choose a channel to record from the EPG Guide by using the INFO button. Time Shift 1. To pause and resume live TV channel, press the PAUSE button, The default time for Time-Shift is 30 minutes.
Explain how to download S/W by USB and how to upload and download channels by USB How to download S/W or Channel data by USB. . Insert USB Memory Stick to USB Port after opening Front Cover.(See below drawing) . Press MENU Key to go Main menu 3.
4. Click on Browse in the TM Loader. 5. Select the file from where you saved it when you downloaded it from the Technomate web site. 6. Click on Connect on TM Loader. 7. Turn ON the satellite receiver.
Page 33
Note. How to download/upload Channels If you want to download /upload Channels, Click on Channels in the TM Loader, then select Download/upload * Downloading Channels from PC to TM-8000 Series. 1. Click on Download, and then Click on Browse in the TM Loader. 2.
Trouble Shooting There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact the dealer. Don't open the receiver cover. It may cause a dangerous situation. Symptom Cause Remedy...
Specifications Fully DVB compliant System capabilities Connector IEC 169-24, female Satellite Frequency range 950MHz~2150MHz LNB/Tuner input Signal level -65dBm~-25 dBm LNB supply DC 13/18, max 400mA LNB switch control 22KHz DiSEqC Ver 1.0/1.1/1.2/USALS Compatible Front end DVB-S/S2 QPSK, 8PSK Demodulator Symbol rate DVB-S : 1~45Msps DVB-S2 : 10~30Msps(QPSK)
Page 36
RF Modulator RF-Connector 75ohm IEC169-2, Male/Female Frequency 470MHz to 860MHz Output Channel CH 21-69 for the Demodulator TV Standard PAL B/G/I/D/K Selectable by Menu Setting Audio Output Mono with Volume Control Preset Channel CH 40, Software changeable by Menu screen Power Supply Input Voltage AC90 to 240V, 50Hz/60Hz...
Glossary of Terms C band 3.7 ~ 4.2 GHz Frequency. Ku band 11 ~ 18GHz Frequency. DiSEqC Digital Satellite Equipment Control. LNB (Low-Noise Block converter) The LNB is an electronic unit mounted on the satellite dish. It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver.