1. Manuals
  2. Brands
  3. Creative Playthings Manuals
  4. Swing Set
  5. Playtime PS10LIN
  6. Assembly manual

Creative Playthings Playtime PS10LIN Assembly Manual

Playtime swing sets
Hide thumbs
Table of Contents

Advertisement

Quick Links

MODEL PS10LIN
ASSEMBLY MANUAL
Model PS10LIN with
Top Ladder
Model PS10LIN with
Swing Beam
If you have problems or questions about your Creative Playthings Playset,
Contact Creative Playthings Customer Service at 1-800-833-4001 or
All hardware on this set is specially coated
for corrosion resistance.
If non-Creative Playthings hardware is used,
it must be galvanized or stainless steel.
This product is intended for single
family home/residential use only and
not intended for use in any public
setting. Placement in any public
setting constitutes a misuse of this
product.
DO NOT CALL THE RETAILER.
customerservice@creativeplaythings.com
™
Please
read
the
assembling
your
additional information on the care and use of
your Playset.
You must carefully read the entire instruction
manual before proceeding with the assembly
or use of your new Playset.
Creative Playthings takes great care to design
its products with your child's safety in mind.
However, only with careful supervision
and proper safety instructions, can you be
assured of safe play time on any product
designed for children.
By
owner's
manual
Playset,
it
provides
before

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Playtime PS10LIN and is the answer not in the manual?

Questions and answers

Related Manuals for Creative Playthings Playtime PS10LIN

Summary of Contents for Creative Playthings Playtime PS10LIN

  • Page 1 MODEL PS10LIN ASSEMBLY MANUAL Model PS10LIN with Top Ladder Model PS10LIN with Swing Beam If you have problems or questions about your Creative Playthings Playset, DO NOT CALL THE RETAILER. Contact Creative Playthings Customer Service at 1-800-833-4001 or customerservice@creativeplaythings.com Please read owner’s...
  • Page 2 Hanging accessories MUST be removed prior to using overhead monkey bars. Do not allow children under age 7 to use monkey bars unless supported by an adult. by Creative Playthings include; Dog runs, clothes lines, electrical devices, or bird feeders etc. and Wooden Lawn Swing Glider.
  • Page 3 (2 M) (2 M) Whichever is greater (4.27 M) Landscape Timbers 6' from (2 M) play structure. A FALL ONTO A HARD SURFACE COULD RESULT IN SERIOUS INJURY. MODEL PS10LIN © Copyright 2010, Creative Playthings Page 3 19764-100 Rev D (05-10)
  • Page 4 Truss Head Bolt 1/4 x 1" 17001-104 Weld Nut 1/4" 12017-205 Lock Washer 1/4" 12002-205 Flat Washer 1/4" 12002-206 Flat Washer 5/16" We have packaged more hardware than is required for assembly. MODEL PS10LIN Page 4 © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 5 It is very important to make certain a socket to tighten. with the surface of the wood and there are no protruding sharp edg- MODEL PS10LIN © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 6 2 40304-400 Glider Handle, Green w/Chain 1 40381-100 Plastic Ring Trap Combo, Yellow 1 40311-402 Ring Trapeze Assembly w/Chain Telescope 1 15086-400 Glider Seat, Green 1 15086-400 Glider Seat, Green MODEL PS10LIN © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 7 Assembly Take inventory of all parts, making sure nothing is missing or the Creative Playthings Customer Service Department at 1-800-833-4001. * Not visible in illustration 9 on Page 6 AC 3 33250-102 Right Rock Board 5/4 x 6 x 23-1/2"...
  • Page 8 Maintenance: depending on weather climate. rusted or structural pieces have signs of premature failure; replace them through Creative Playthings Customer Service. indoors when outside temperatures drop below 32° F (0° C). are a natural characteristic of all wood and will not affect the strength or durability of the wooden components.
  • Page 9 Fasten the Right Platform Side (AT) to the Corner Posts op- posite the Left Platform Side using four 1/4 x 4-1/2" Hex Bolt Assemblies. 4-1/2" Hex Bolt MODEL PS10LIN © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 10 Platform Side. Attach the Platform Stringer using two 5/16 x 4" Lag Screws and Flat Washers as shown. Make sure the Platform Sides and Platform Stringer align across the Bot- tom edge. MODEL PS10LIN Page 10 © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 11 Narrow Platform Boards to the Stringers with three #10 x 1-1/2" Screws for each board. Do not fasten Narrow Platform Boards until after Step 32 MODEL PS10LIN © Copyright 2010, Creative Playthings Page 11 19764-100 Rev D (05-10)
  • Page 12 Fasten the Long Tent Supports (I) to the Corner Posts, as shown, using two 1/4 x 4-1/2" Hex Bolt Assemblies each. The two holes at the center should be offset nearer the top of the support. MODEL PS10LIN Page 12 © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 13 Fasten the other Tent Post (H) to the back End Tent Support using two 1/4 x 2-1/2" Hex Bolt Assemblies. Fasten the Tent Beam (J) to the top of the Tent Posts using four #10 x 3" Screws. MODEL PS10LIN © Copyright 2010, Creative Playthings Page 13 19764-100 Rev D (05-10)
  • Page 14 Position the Access Ladder Assembly against the Platform Front. Fasten the Access Ladder Brackets to the Platform Front using 5/16 x 1" Hex Bolt Assemblies, as shown. Tighten all hardware. MODEL PS10LIN Page 14 © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 15 Use four #8 x 2-1/2" Screws for each Sand- box Seat. Be careful not to split the Sandbox Sides or Ends. A 1/8" diameter pilot hole 1" deep is recommended. MODEL PS10LIN © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 16 Fasten the Left Rock Board using four #10 x 2" Wood Screws. Continue fastening Spacer Boards (AE) alternating with Right Rock Boards (AC) or Left Rock Boards as shown at right. rights for each #10 x 2" Wood Screw. MODEL PS10LIN © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 17 Mullion with one #10 x -1/2" Screw. Make sure that the Transom is level and fasten it to the Wall Slats using two # 10 x 1-1/2" Screws. MODEL PS10LIN © Copyright 2010, Creative Playthings Page 17 19764-100 Rev D (05-10)
  • Page 18 Top Ladder Rails should be closed off using two Wall Slats, unless the Top Ladder is to be used as Monkey Bars. If this space is left open, the swings should be removed to MODEL PS10LIN Page 18 © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)
  • Page 19 Screws. Stretch the Tent smoothly and evenly across the Tent Beam. Secure the other End of the Tent to the left End Tent Support in the same manner. MODEL PS10LIN © Copyright 2010, Creative Playthings 19764-100 Rev D (05-10)

  • Page 20: Thank You

    Save all instruction sheets and receipts in case it becomes necessary to contact Creative Playthings for warranty service and/or part replacement. The warranty can be found in your Owner’s Manual.

Table of Contents