Page 1
SPEED TOUCH PC ADSL PC Network Interface Card Installation Guide Microsoft Windows 95A, 98 and NT4.0 VERSION 2.1.1 – for CD-ROM Installation November 9, 1999...
Page 2
SPEED TOUCH PC ADSL PC Network Interface Card Installation Guide Microsoft Windows 95A, 98 and NT4.0 VERSION 2.1.1– for CD-ROM Installation November 9, 1999...
Diagnostic Tools ....................36 Appendix A – Upgrade Microsoft DUN Version 1.3 ........37 Appendix B – Verifying Dial-Up Networking (DUN) Status ......38 Appendix C – Removing Speed Touch PC NIC Drivers........39 Windows 95, 98..................39 Windows NT4.0 ..................39 Appendix D –...
INTRODUCTION Congratulations! You’ll soon have the fastest connection available to the Internet – thanks to Alcatel’s Speed Touch PC. The Alcatel Speed Touch PC is an internal Asymmetric Digital Subscriber Line (ADSL) PC Network Interface Card (NIC), which conveniently plugs into your computer system. Alcatel’s Speed Touch PC connects directly to your telephone line via a standard RJ-11 connector and is fully plug-and-play compatible.
Page 5
Alcatel Speed Touch™ PC Installation Guide On the desktop, right click My Computer. Then select Properties. The version number of the Microsoft Windows Operating System installed in your computer will be displayed. Refer to the following table for more detailed information.
Windows Operating System, please contact your original PC manufacturer or Microsoft for assistance. • If you have questions regarding Speed Touch PC, please refer to the Speed Touch PC User Manual contained on the Alcatel CD supplied, or visit the Web site: www.alcateldsl.com...
1.3 or above. Please refer to Appendix A on how to upgrade your system’s DUN. HARDWARE INSTALLATION To install the Alcatel Speed Touch PC in your PC, proceed through the following steps: WARNING! To avoid possible damage to your Speed Touch PC card you need to use an anti-static grounding device or hold onto the metal chassis of the PC to provide anti-static grounding.
27 NT 4.0 go to page 31 POINT TO POINT SERVICE FOR WINDOWS 95A 1. After installing the Alcatel Speed Touch PC card, power on the PC system. The Hardware Wizard will detect the card as a PCI Network Controller.
Page 9
Diagnostic Tools with Red lights indicate a connection error or driver load error. Verify that the cable is properly connected to the data port of the service and the Speed Touch PC card. 6. You must now make a network connection, go to page 21.
POINT TO POINT SERVICE FOR WINDOWS 95B 1. After installing the Alcatel Speed Touch PC card, power-up the PC system. The Hardware wizard will detect the Alcatel Speed Touch PC as a PCI Network Controller, click Next 2. Insert the Alcatel Speed Touch PC Device Driver CD into the CD drive.
Page 11
:\WIN95 (e.g. D:\WIN95) and click OK. 8. At the conclusion of the Speed Touch PC driver installation, the Diagnostic Tool icon is active and monitoring connectivity. Diagnostic Tool with blinking or solid Black or Green lights indicates a good connection.
Installation Guide POINT TO POINT SERVICE FOR WINDOWS 98, 98A 1. After installing the Speed Touch PC card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next.
Page 13
Address, click OK. The previous Service Option window will appear, click Next. 7. Additional files are copied from the Speed Touch PC disk to the hard drive. In addition, files are now copied from the Windows CD (system CAB files) to the hard drive.
Page 14
Diagnostic Tools with Red lights indicate a connection error or driver load error. Verify that the cable is properly connected to the data port of the service and Speed Touch PC card. 12. You must now make a dial-up network connection. At the task...
Page 15
Alcatel Speed Touch™ PC Installation Guide 15. Make New Connection is complete. Click Finish. 16. The new connection will appear in the Dial-Up Networking window. 17. Double-click the My Connection icon to begin a Dial-Up session. 18. Enter the User Name and Password supplied by the Internet service provider.
Page 16
Alcatel Speed Touch™ PC Installation Guide 20. The PPPoA service connection is now established. Click Close and the PPPoA icon appears on the task bar. Congratulations, you are done. Your Speed Touch to the Internet is established! page 13...
Adapters tab. 3. Click Add (to add new adapters). 4. In the Select Network Adapter window click Have Disk. 5. Insert the Alcatel Speed Touch PC Device Driver CD into the CD-ROM drive, enter the < CD drive letter> :\PPPoANT4 (e.g.
Page 18
<CD drive letter>:\i386 (e.g. D:\i386) then click Continue. 10. The Add RAS Device window appears. Click OK 11. The Remote Access Setup will appear showing the Alcatel Speed Touch PC card. Click Network to display the network page 15...
Page 19
Click OK. 13. The Network window will appear at the conclusion of the installation to confirm installation of the Alcatel SPEED TOUCH 14. Click on Protocols tab and verify that the ADSL Management and Monitor Interface is present. page 16...
Page 20
Alcatel Speed Touch™ PC Installation Guide 15. Still in the Network window, click on the Services tab to verify that the Remote Access Service is present. Click Close. Note: To review the Network window properties at any time, right-click the Network Neighborhood icon and select Properties.
Page 21
Alcatel Speed Touch™ PC Installation Guide 17. After the system restarts the Diagnostic Tools icon will appear on the task bar. When the Speed Touch PC card is connected to the ADSL data port, both panels of the icon will appear black signifying an ADSL connection.
Page 22
Alcatel Speed Touch™ PC Installation Guide 22. When the Server window appears click Next. 23. The Dial-Up Networking window prompts for the phone number of the dial-up server. Unless instructed to enter a phone number by the ISP, enter zero “0” Still at the Dial-Up Networking window, click More.
Page 23
Alcatel Speed Touch™ PC Installation Guide Note: The text “Verifying username and password…” will be displayed while logon authentication takes place. Note: If this screen persists and a connection logon error is reported, confirm that the correct Username and Password are entered and try the connection again.
My Connection) and set the connection device to Alcatel SPEED TOUCH PC. NOTE: use the scroll down menu to locate the Alcatel Speed Touch PC card; then click Next. 4. Enter the Host Name or IP Address, if provided by your ISP, otherwise enter (0) zero, and then click Finish.
Page 25
Alcatel Speed Touch™ PC Installation Guide 5. The new connection will appear in the Dial-Up Networking window. Double-click the My Connection icon to begin a Dial- Up session. 6. Enter the User Name and Password supplied by the Internet service provider. Then click Connect.
BRIDGED ETHERNET SERVICE FOR WINDOWS 95A 1. After installing the Speed Touch PC card, power on the PC system. The Hardware Wizard will detect the Speed Touch PC as a PCI Network Controller. Select the Driver from disk provided by hardware manufacturer option.
Page 27
NOTE: If during the file copying process a file is reported as “not found” enter the path <CD drive letter> :\Win95 (e.g. D:\Win95) 5. At the conclusion of the Speed Touch PC driver installation, the Diagnostic Tool icon will appear disabled on the task bar.
Alcatel Speed Touch™ PC Installation Guide BRIDGED ETHERNET SERVICE FOR WINDOWS 95B 1. After installing the Speed Touch PC card, power-up the PC System. 2. The Hardware wizard will detect the Alcatel Speed Touch PC as a PCI Network Controller, click Next.
Page 29
Alcatel Speed Touch™ PC Installation Guide 6. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. NOTE: If you clicked Advanced, the Service Options window shows the Connection Address.
Click Next. 2. Then select Search for the best driver for your device. Click Next. 3. Insert the CD labeled Alcatel Speed Touch PC Driver into your CD-ROM drive. 4. Then select Specify a location, enter <CD drive letter>...
Page 31
Alcatel Speed Touch™ PC Installation Guide 6. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. NOTE: If you click Advanced, the Connection Address window appears.
TOUCH PC and click Properties. NOTE: In Win95/95A/95B, you may not find TCP/IP->Alcatel Speed Touch PC card. If this is the case, find and select the TCP/IP and click Properties. 4. The TCP/IP Properties window appears. Select IP Address tab.
Page 33
Click Ok to restart the system. After the system restarts, configure the Internet browser. Once the Internet browser is configured properly, you will enjoy high-speed access to Internet with your Alcatel Speed Touch PC. page 30...
Network window. 2. Click Add (to add new adapters). 3. In the Select Network Adapter window click Have Disk. 4. Insert the Alcatel Speed Touch PC driver CD into the drive, enter the < CD drive letter> :\1483NT4 (e.g.D:\1483NT4) and click OK.
Page 35
Alcatel Speed Touch™ PC Installation Guide 5. The Select OEM Option window will find the Alcatel SPEED TOUCH PC card. Click OK. The system will copy the drivers to the hard drive. 6. When the Service Option window appears, click Next for the default installation.
Alcatel Speed Touch™ PC Installation Guide information. When not connecting to a DHCP server, enter the IP address (e.g. 192.168.4.39). 8. Enter the Subnet Mask (e.g. 255.255.255.0). 9. Enter the Default Gateway address. Note: Consult your ISP for the TCP/IP Properties.
Page 37
Alcatel Speed Touch™ PC Installation Guide illustrative differences, the process for editing the IP address settings is the same for Windows NT 4.0 and Windows 95/98. 2. At the desktop, double click My Computer, then double click Control Panel to view the contents of the control panel.
Page 38
Alcatel Speed Touch™ PC Installation Guide 8. Enter the Host Name (e.g. speed_touch) and Domain (e.g. pacbell.net). Note: To enter the Domain search (DNS) entries, click Add then enter the address. Click Add to save the address. Repeat the process for additional DNS entries.
Alcatel Speed Touch™ PC Installation Guide DIAGNOSTIC TOOLS The diagnostic tools allow the user to monitor the ADSL connectivity, setup the service connection address, and run diagnostic tests. The Diagnostic Tools icon is displayed on the task bar as shown.
Alcatel Speed Touch™ PC Installation Guide APPENDIX A - UPGRADE MICROSOFT DUN VERSION 1.3 This section explains how to upgrade Microsoft’s Dial-Up Networking (DUN) application. You can download the DUN application from Microsoft’s Web page and install it into your system. Please follow the instruction below.
Alcatel Speed Touch™ PC Installation Guide APPENDIX B – VERIFYING DIAL-UP NETWORKING (DUN) STATUS 1. It is possible to have Dial-Up Networking (DUN) version 1.2B or above, but not have the Dial-Up Networking components loaded in the Windows environment. This procedure is for determining the status of DUN on the PC system.
Alcatel Speed Touch™ PC Installation Guide APPENDIX C – REMOVING SPEED TOUCH PC DRIVERS WINDOWS 95, 98 1. To Delete Alcatel Speed Touch PC drivers; on the desktop, right- click on My Computer, then click Properties, then click on the Device Manager tab, then double click Network adapters.
Page 43
Installation Guide 3. A warning message will inform you that a component is about to be removed. Click Yes. 4. Once the Alcatel SPEED TOUCH PC is removed from the adapter list, click Close. 5. The PC system must be restarted for the changes to take effect.
Alcatel Speed Touch™ PC Installation Guide APPENDIX D: Power Requirements • .75A Max @ +5V ± 5%, 0.1A max @ ± 12V, ± 5% Environmental Requirements • Operating Temperature: 0 °C to 70°C with airflow • Non-operating Temperature: -10 °C to 85 °C •...
Integrated Telecom Express, Inc. Speed Touch PC is a trademark of Alcatel. All other product names are trademarks and or registered trademarks of their respective companies.